*New 11.3 series Release:
2019-10-05: XigmaNAS 11.3.0.4.6928 - released, 11.2 series are soon unsupported!

*New 12.0 series Release:
2019-10-05: XigmaNAS 12.0.0.4.6928 - released!

*New 11.2 series Release:
2019-09-23: XigmaNAS 11.2.0.4.6881 - released!

We really need "Your" help on XigmaNAS https://translations.launchpad.net/xigmanas translations. Please help today!

Producing and hosting XigmaNAS costs money. Please consider donating for our project so that we can continue to offer you the best.
We need your support! eg: PAYPAL

SAS2308 probs with ST10000VN0004-2GS11L - Seagate IronWolf 10TB

Hard disks, HDD, RAID Hardware, disk controllers, SATA, PATA, SCSI, IDE, On Board, USB, Firewire, CF (Compact Flash)
Forum rules
Set-Up GuideFAQsForum Rules
Post Reply
nasser
Starter
Starter
Posts: 43
Joined: 01 May 2017 21:00
Status: Offline

SAS2308 probs with ST10000VN0004-2GS11L - Seagate IronWolf 10TB

#1

Post by nasser » 15 Jun 2019 19:03

Hello,

since month I have the problem of disconnecting HDDs (two).
Supermicro SC836 Backplane, ASRock C2750D4I board
A fan cools the controller very voll

what I tried:
- cables
- slots
- SAS HDD, even with CCF_STOPP=2
- EPC disabled with SeaChest
- smart ok
- connected directly to mainboard controller and the LSI (without backplane)

Does anyone have another approach for that?
Many thanks in advance!

Code: Select all

ahcich3: Timeout on slot 11 port 0
ahcich3: is 00000000 cs 00000800 ss 00000800 rs 00000800 tfd 40 serr 00000000 cmd 10008a17
(ada2:ahcich3:0:0:0): WRITE_FPDMA_QUEUED. ACB: 61 08 68 e7 79 40 52 00 00 00 00 00
(ada2:ahcich3:0:0:0): CAM status: Command timeout
(ada2:ahcich3:0:0:0): Retrying command
(aprobe0:ahcich3:0:0:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00 00 00 00
(aprobe0:ahcich3:0:0:0): CAM status: ATA Status Error
(aprobe0:ahcich3:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT )
(aprobe0:ahcich3:0:0:0): RES: 51 04 00 00 00 00 00 00 00 00 00
(aprobe0:ahcich3:0:0:0): Retrying command
(aprobe0:ahcich3:0:0:0): ATA_IDENTIFY. ACB: ec 00 00 00 00 40 00 00 00 00 00 00
(aprobe0:ahcich3:0:0:0): CAM status: ATA Status Error
(aprobe0:ahcich3:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT )
(aprobe0:ahcich3:0:0:0): RES: 51 04 00 00 00 00 00 00 00 00 00
(aprobe0:ahcich3:0:0:0): Error 5, Retries exhausted
ada2 at ahcich3 bus 0 scbus4 target 0 lun 0
ada2: <ST10000VN0004-1ZD101 SC60> s/n ZA27MK8W detached
(ada2:ahcich3:0:0:0): SETFEATURES ENABLE RCACHE. ACB: ef aa 00 00 00 40 00 00 00 00 00 00
(ada2:ahcich3:0:0:0): CAM status: ATA Status Error
(ada2:ahcich3:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT )
(ada2:ahcich3:0:0:0): RES: 51 04 00 00 00 00 00 00 00 00 00
(ada2:ahcich3:0:0:0): Error 5, Periph was invalidated
(ada2:ahcich3:0:0:0): SETFEATURES ENABLE WCACHE. ACB: ef 02 00 00 00 40 00 00 00 00 00 00
(ada2:ahcich3:0:0:0): CAM status: ATA Status Error
(ada2:ahcich3:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 04 (ABRT )
(ada2:ahcich3:0:0:0): RES: 51 04 00 00 00 00 00 00 00 00 00
(ada2:ahcich3:0:0:0): Error 5, Periph was invalidated
....
(da2:mps0:0:13:0): Retrying command (per sense data)
(da2:mps0:0:13:0): READ(10). CDB: 28 00 02 00 00 28 00 00 08 00
(da2:mps0:0:13:0): CAM status: SCSI Status Error
(da2:mps0:0:13:0): SCSI status: Check Condition
(da2:mps0:0:13:0): SCSI sense: NOT READY asc:4,0 (Logical unit not ready, cause not reportable)
(da2:mps0:0:13:0): Error 5, Retries exhausted
...
        (da4:mps0:0:18:0): READ(10). CDB: 28 00 02 00 00 28 00 00 08 00 length 4096 SMID 765 terminated ioc 804b loginfo 31120100 scsi 0 state c xfer 0
(da4:mps0:0:18:0): READ(10). CDB: 28 00 02 00 00 28 00 00 08 00
(da4:mps0:0:18:0): CAM status: CCB request completed with an error
(da4:mps0:0:18:0): Retrying command
        (da4:mps0:0:18:0): READ(10). CDB: 28 00 02 00 00 28 00 00 08 00 length 4096 SMID 723 terminated ioc 804b loginfo 31120100 scsi 0 state c xfer 0
(da4:mps0:0:18:0): READ(10). CDB: 28 00 02 00 00 28 00 00 08 00
(da4:mps0:0:18:0): CAM status: CCB request completed with an error
(da4:mps0:0:18:0): Error 5, Retries exhausted


Code: Select all

device model          ST10000VN0004-2GS11L ( Seagate IronWolf 10TB )
firmware revision     SC60

board: asrock C2750D4I

mps0: <Avago Technologies (LSI) SAS2308> port 0xd000-0xd0ff mem 0xdf740000-0xdf74ffff,0xdf700000-0xdf73ffff irq 16 at device 0.0 on pci1
mps0: Firmware: 20.00.07.00, Driver: 21.02.00.00-fbsd
mps0: IOCCapabilities: 5a85c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,MSIXIndex,HostDisc>

nas4free: ~# ./sas2ircu 0 display
LSI Corporation SAS2 IR Configuration Utility.
Version 20.00.00.00 (2014.09.18)
Copyright (c) 2008-2014 LSI Corporation. All rights reserved.

Read configuration has been initiated for controller 0
------------------------------------------------------------------------
Controller information
------------------------------------------------------------------------
  Controller type                         : SAS2308_2
  BIOS version                            : 7.37.00.00
  Firmware version                        : 20.00.07.00
  Channel description                     : 1 Serial Attached SCSI
  Initiator ID                            : 0
  Maximum physical devices                : 1023
  Concurrent commands supported           : 10240
  Slot                                    : 17
  Segment                                 : 0
  Bus                                     : 1
  Device                                  : 0
  Function                                : 0
  RAID Support                            : No
------------------------------------------------------------------------

Post Reply

Return to “Hard disk & controller”