XigmaNAS

Welcome to the XigmaNAS community forum!
https://www.xigmanas.com/oldforums/

No USB after NAS4Free boot

https://www.xigmanas.com/oldforums/viewtopic.php?f=15&t=5879

Page 1 of 1

No USB after NAS4Free boot

Posted: 18 Jan 2014 20:32
by martl
I boot Nas4Free 9.2.0.1.925 from CD.
Until the prompt
'Welcome to NAS4Free
1. Boot NAS4Free in Normal Mode
2.
'
my USB Keyboard (attached to a rear USB 2.0 port) works fine, i can type 1 or 2 to start booting or space and go to loader prompt.

After that USB is dead.

In
'Console Setup

1)
..
9)

Enter a number'
the USB Keyboard is not working any more

The same happens when I boot from img USB-Stick.
Boot starts OK, but then it stops with the message that config.xml cannot be written.

When I'm at Console Setup i can insert a USB Stick, but then message
'uhub_reattach_port: could not allocate new device' appears.
Same as witten here: http://www.bsdforen.de/threads/freebsd- ... ost-255199
Should i modify a conf file?

When I try FreeNAS 9.2 USB works.

Hardware:

Intel DH87RL Board.
UEFI Bios
USB Legacy Mode enabled (if I disable no USB is visible)

Any Suggestions?

Re: No USB after NAS4Free boot

Posted: 19 Jan 2014 04:23
by armandh
booting from a CD let the first prompt time out and the cd will complete the boot
the USB flash in conjunction with the CD is for the config file only not the OS.
if MOBO hardware will boot from the USB port use step 9 [second prompt] to install the embedded OS on the usb flash then remove the CD
one can also install to a small Hdd, SATA or PATA connected IDE flash
assuming the above
however un likely you may have a KB compatibility issue or usb chip compatibility issue
at first it is the bios connecting the KB check for any bios settings for USB compatability
is there a round KB plug available for a conventional KB.
worst case it might be a bad OS down load in the usb driver area

Re: No USB after NAS4Free boot

Posted: 19 Jan 2014 20:37
by martl
armandh wrote:booting from a CD let the first prompt time out and the cd will complete the boot
the USB flash in conjunction with the CD is for the config file only not the OS.
if MOBO hardware will boot from the USB port use step 9 [second prompt] to install the embedded OS on the usb flash then remove the CD
one can also install to a small Hdd, SATA or PATA connected IDE flash
Can't hit #9 because USB KB is not working, I guess there's no USB-Flash available anymore at that stage anyway...
I can access the GUI via 192.168.1.250, is there a way to trigger the install (to SATA) from there?
armandh wrote: assuming the above
however un likely you may have a KB compatibility issue or usb chip compatibility issue
at first it is the bios connecting the KB check for any bios settings for USB compatability
is there a round KB plug available for a conventional KB.
No PS/2 KB plug available on the DH87RL Board :cry:

Re: No USB after NAS4Free boot

Posted: 19 Jan 2014 21:24
by alexey123
martl wrote: I can access the GUI via 192.168.1.250, is there a way to trigger the install (to SATA) from there?
Yes, You can install now.
1. Enable ssh and Permit Root Login
2. Connect over ssh and type command

Code: Select all

/etc/rc.initial
3. Do install.

Re: No USB after NAS4Free boot

Posted: 20 Jan 2014 19:09
by filius27
Unable to open configuration file /etc/hast.conf
No such file or directory
link /var/etc/hast.conf empty (no hast.conf)

filius27

Re: No USB after NAS4Free boot

Posted: 20 Jan 2014 19:32
by filius27
Hallo,

meine boot log

Code: Select all

Jan 20 10:56:33 nas4free syslogd: kernel boot file is /boot/kernel/kernel
Jan 20 10:56:33 nas4free kernel: Copyright (c) 1992-2013 The FreeBSD Project.
Jan 20 10:56:33 nas4free kernel: Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
Jan 20 10:56:33 nas4free kernel: The Regents of the University of California. All rights reserved.
Jan 20 10:56:33 nas4free kernel: FreeBSD is a registered trademark of The FreeBSD Foundation.
Jan 20 10:56:33 nas4free kernel: FreeBSD 9.2-RELEASE-p3 #0 r260900M: Mon Jan 20 07:22:46 CET 2014
Jan 20 10:56:33 nas4free kernel: root@dev.nas4free.org:/usr/obj/nas4free/usr/src/sys/NAS4FREE-amd64 amd64
Jan 20 10:56:33 nas4free kernel: gcc version 4.2.1 20070831 patched [FreeBSD]
Jan 20 10:56:33 nas4free kernel: CPU: Intel(R) Core(TM) i3-4130 CPU @ 3.40GHz (3399.08-MHz K8-class CPU)
Jan 20 10:56:33 nas4free kernel: Origin = "GenuineIntel"  Id = 0x306c3  Family = 0x6  Model = 0x3c  Stepping = 3
Jan 20 10:56:33 nas4free kernel: Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Jan 20 10:56:33 nas4free kernel: Features2=0x7fdafbbf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,<b11>,FMA,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,MOVBE,POPCNT,TSCDLT,AESNI,XSAVE,OSXSAVE,AVX,F16C,RDRAND>
Jan 20 10:56:33 nas4free kernel: AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM>
Jan 20 10:56:33 nas4free kernel: AMD Features2=0x21<LAHF,ABM>
Jan 20 10:56:33 nas4free kernel: Standard Extended Features=0x27ab<GSFSBASE,TSCADJ,SMEP,ENHMOVSB,INVPCID>
Jan 20 10:56:33 nas4free kernel: TSC: P-state invariant, performance statistics
Jan 20 10:56:33 nas4free kernel: real memory  = 17179869184 (16384 MB)
Jan 20 10:56:33 nas4free kernel: avail memory = 15934369792 (15196 MB)
Jan 20 10:56:33 nas4free kernel: Event timer "LAPIC" quality 600
Jan 20 10:56:33 nas4free kernel: ACPI APIC Table: <ALASKA A M I>
Jan 20 10:56:33 nas4free kernel: FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
Jan 20 10:56:33 nas4free kernel: FreeBSD/SMP: 1 package(s) x 2 core(s) x 2 SMT threads
Jan 20 10:56:33 nas4free kernel: cpu0 (BSP): APIC ID:  0
Jan 20 10:56:33 nas4free kernel: cpu1 (AP): APIC ID:  1
Jan 20 10:56:33 nas4free kernel: cpu2 (AP): APIC ID:  2
Jan 20 10:56:33 nas4free kernel: cpu3 (AP): APIC ID:  3
Jan 20 10:56:33 nas4free kernel: ACPI Warning: FADT (revision 5) is longer than ACPI 2.0 version, truncating length 268 to 244 (20110527/tbfadt-320)
Jan 20 10:56:33 nas4free kernel: ioapic0 <Version 2.0> irqs 0-23 on motherboard
Jan 20 10:56:33 nas4free kernel: kbd1 at kbdmux0
Jan 20 10:56:33 nas4free kernel: cryptosoft0: <software crypto> on motherboard
Jan 20 10:56:33 nas4free kernel: acpi0: <ALASKA A M I> on motherboard
Jan 20 10:56:33 nas4free kernel: acpi0: Power Button (fixed)
Jan 20 10:56:33 nas4free kernel: acpi0: reservation of 67, 1 (4) failed
Jan 20 10:56:33 nas4free kernel: cpu0: <ACPI CPU> on acpi0
Jan 20 10:56:33 nas4free kernel: cpu1: <ACPI CPU> on acpi0
Jan 20 10:56:33 nas4free kernel: cpu2: <ACPI CPU> on acpi0
Jan 20 10:56:33 nas4free kernel: cpu3: <ACPI CPU> on acpi0
Jan 20 10:56:33 nas4free kernel: hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Jan 20 10:56:33 nas4free kernel: Timecounter "HPET" frequency 14318180 Hz quality 950
Jan 20 10:56:33 nas4free kernel: Event timer "HPET" frequency 14318180 Hz quality 550
Jan 20 10:56:33 nas4free kernel: Event timer "HPET1" frequency 14318180 Hz quality 440
Jan 20 10:56:33 nas4free kernel: Event timer "HPET2" frequency 14318180 Hz quality 440
Jan 20 10:56:33 nas4free kernel: Event timer "HPET3" frequency 14318180 Hz quality 440
Jan 20 10:56:33 nas4free kernel: Event timer "HPET4" frequency 14318180 Hz quality 440
Jan 20 10:56:33 nas4free kernel: atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
Jan 20 10:56:33 nas4free kernel: atrtc0: Warning: Couldn't map I/O.
Jan 20 10:56:33 nas4free kernel: Event timer "RTC" frequency 32768 Hz quality 0
Jan 20 10:56:33 nas4free kernel: attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Jan 20 10:56:33 nas4free kernel: Timecounter "i8254" frequency 1193182 Hz quality 0
Jan 20 10:56:33 nas4free kernel: Event timer "i8254" frequency 1193182 Hz quality 100
Jan 20 10:56:33 nas4free kernel: Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
Jan 20 10:56:33 nas4free kernel: acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1808-0x180b on acpi0
Jan 20 10:56:33 nas4free kernel: pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
Jan 20 10:56:33 nas4free kernel: pci0: <ACPI PCI bus> on pcib0
Jan 20 10:56:33 nas4free kernel: vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem 0xf0000000-0xf03fffff,0xe0000000-0xefffffff irq 16 at device 2.0 on pci0
Jan 20 10:56:33 nas4free kernel: hdac0: <Intel (0x0c0c) HDA Controller> mem 0xf0734000-0xf0737fff irq 16 at device 3.0 on pci0
Jan 20 10:56:33 nas4free kernel: xhci0: <Intel Lynx Point USB 3.0 controller> mem 0xf0720000-0xf072ffff irq 16 at device 20.0 on pci0
Jan 20 10:56:33 nas4free kernel: xhci0: 32 byte context size.
Jan 20 10:56:33 nas4free kernel: usbus0 on xhci0
Jan 20 10:56:33 nas4free kernel: pci0: <simple comms> at device 22.0 (no driver attached)
Jan 20 10:56:33 nas4free kernel: em0: <Intel(R) PRO/1000 Network Connection 7.3.8> port 0xf080-0xf09f mem 0xf0700000-0xf071ffff,0xf073d000-0xf073dfff irq 20 at device 25.0 on pci0
Jan 20 10:56:33 nas4free kernel: em0: Using an MSI interrupt
Jan 20 10:56:33 nas4free kernel: em0: Ethernet address: bc:5f:f4:e8:6d:af
Jan 20 10:56:33 nas4free kernel: ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf073c000-0xf073c3ff irq 16 at device 26.0 on pci0
Jan 20 10:56:33 nas4free kernel: usbus1: EHCI version 1.0
Jan 20 10:56:33 nas4free kernel: usbus1 on ehci0
Jan 20 10:56:33 nas4free kernel: hdac1: <Intel Lynx Point HDA Controller> mem 0xf0730000-0xf0733fff irq 22 at device 27.0 on pci0
Jan 20 10:56:33 nas4free kernel: pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
Jan 20 10:56:33 nas4free kernel: pci1: <ACPI PCI bus> on pcib1
Jan 20 10:56:33 nas4free kernel: pcib2: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
Jan 20 10:56:33 nas4free kernel: pci2: <ACPI PCI bus> on pcib2
Jan 20 10:56:33 nas4free kernel: pci2: <network> at device 0.0 (no driver attached)
Jan 20 10:56:33 nas4free kernel: ehci1: <EHCI (generic) USB 2.0 controller> mem 0xf073b000-0xf073b3ff irq 23 at device 29.0 on pci0
Jan 20 10:56:33 nas4free kernel: usbus2: EHCI version 1.0
Jan 20 10:56:33 nas4free kernel: usbus2 on ehci1
Jan 20 10:56:33 nas4free kernel: isab0: <PCI-ISA bridge> at device 31.0 on pci0
Jan 20 10:56:33 nas4free kernel: isa0: <ISA bus> on isab0
Jan 20 10:56:33 nas4free kernel: ahci0: <Intel Lynx Point AHCI SATA controller> port 0xf0d0-0xf0d7,0xf0c0-0xf0c3,0xf0b0-0xf0b7,0xf0a0-0xf0a3,0xf060-0xf07f mem 0xf073a000-0xf073a7ff irq 19 at device 31.2 on pci0
Jan 20 10:56:33 nas4free kernel: ahci0: AHCI v1.30 with 6 6Gbps ports, Port Multiplier not supported
Jan 20 10:56:33 nas4free kernel: ahcich2: <AHCI channel> at channel 2 on ahci0
Jan 20 10:56:33 nas4free kernel: ahcich3: <AHCI channel> at channel 3 on ahci0
Jan 20 10:56:33 nas4free kernel: ahcich4: <AHCI channel> at channel 4 on ahci0
Jan 20 10:56:33 nas4free kernel: ahcich5: <AHCI channel> at channel 5 on ahci0
Jan 20 10:56:33 nas4free kernel: pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
Jan 20 10:56:33 nas4free kernel: acpi_button0: <Power Button> on acpi0
Jan 20 10:56:33 nas4free kernel: sc0: <System console> at flags 0x100 on isa0
Jan 20 10:56:33 nas4free kernel: sc0: VGA <16 virtual consoles, flags=0x300>
Jan 20 10:56:33 nas4free kernel: vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Jan 20 10:56:33 nas4free kernel: atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
Jan 20 10:56:33 nas4free kernel: atkbd0: <AT Keyboard> irq 1 on atkbdc0
Jan 20 10:56:33 nas4free kernel: kbd0 at atkbd0
Jan 20 10:56:33 nas4free kernel: atkbd0: [GIANT-LOCKED]
Jan 20 10:56:33 nas4free kernel: ppc0: cannot reserve I/O port range
Jan 20 10:56:33 nas4free kernel: ctl: CAM Target Layer loaded
Jan 20 10:56:33 nas4free kernel: coretemp0: <CPU On-Die Thermal Sensors> on cpu0
Jan 20 10:56:33 nas4free kernel: est0: <Enhanced SpeedStep Frequency Control> on cpu0
Jan 20 10:56:33 nas4free kernel: p4tcc0: <CPU Frequency Thermal Control> on cpu0
Jan 20 10:56:33 nas4free kernel: coretemp1: <CPU On-Die Thermal Sensors> on cpu1
Jan 20 10:56:33 nas4free kernel: est1: <Enhanced SpeedStep Frequency Control> on cpu1
Jan 20 10:56:33 nas4free kernel: p4tcc1: <CPU Frequency Thermal Control> on cpu1
Jan 20 10:56:33 nas4free kernel: coretemp2: <CPU On-Die Thermal Sensors> on cpu2
Jan 20 10:56:33 nas4free kernel: est2: <Enhanced SpeedStep Frequency Control> on cpu2
Jan 20 10:56:33 nas4free kernel: p4tcc2: <CPU Frequency Thermal Control> on cpu2
Jan 20 10:56:33 nas4free kernel: coretemp3: <CPU On-Die Thermal Sensors> on cpu3
Jan 20 10:56:33 nas4free kernel: est3: <Enhanced SpeedStep Frequency Control> on cpu3
Jan 20 10:56:33 nas4free kernel: p4tcc3: <CPU Frequency Thermal Control> on cpu3
Jan 20 10:56:33 nas4free kernel: ZFS filesystem version: 5
Jan 20 10:56:33 nas4free kernel: ZFS storage pool version: features support (5000)
Jan 20 10:56:33 nas4free kernel: Timecounters tick every 1.000 msec
Jan 20 10:56:33 nas4free kernel: ipfw2 (+ipv6) initialized, divert loadable, nat loadable, default to accept, logging disabled
Jan 20 10:56:33 nas4free kernel: iSCSI boot driver version 0.2.6
Jan 20 10:56:33 nas4free kernel: hdacc0: <Intel (0x2807) HDA CODEC> at cad 0 on hdac0
Jan 20 10:56:33 nas4free kernel: hdaa0: <Intel (0x2807) Audio Function Group> at nid 1 on hdacc0
Jan 20 10:56:33 nas4free kernel: pcm0: <Intel (0x2807) (HDMI/DP 8ch)> at nid 3 on hdaa0
Jan 20 10:56:33 nas4free kernel: hdacc1: <Realtek (0x0900) HDA CODEC> at cad 0 on hdac1
Jan 20 10:56:33 nas4free kernel: hdaa1: <Realtek (0x0900) Audio Function Group> at nid 1 on hdacc1
Jan 20 10:56:33 nas4free kernel: pcm1: <Realtek (0x0900) (Rear Analog 5.1/2.0)> at nid 20,22,21 and 24,26 on hdaa1
Jan 20 10:56:33 nas4free kernel: pcm2: <Realtek (0x0900) (Front Analog)> at nid 27 and 25 on hdaa1
Jan 20 10:56:33 nas4free kernel: pcm3: <Realtek (0x0900) (Rear Digital)> at nid 30 on hdaa1
Jan 20 10:56:33 nas4free kernel: md0: Preloaded image </mfsroot> 250609664 bytes at 0xffffffff81d894d0
Jan 20 10:56:33 nas4free kernel: usbus0: 5.0Gbps Super Speed USB v3.0
Jan 20 10:56:33 nas4free kernel: usbus1: 480Mbps High Speed USB v2.0
Jan 20 10:56:33 nas4free kernel: usbus2: 480Mbps High Speed USB v2.0
Jan 20 10:56:33 nas4free kernel: ugen0.1: <0x8086> at usbus0
Jan 20 10:56:33 nas4free kernel: uhub0: <0x8086 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
Jan 20 10:56:33 nas4free kernel: ugen1.1: <Intel> at usbus1
Jan 20 10:56:33 nas4free kernel: uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
Jan 20 10:56:33 nas4free kernel: ugen2.1: <Intel> at usbus2
Jan 20 10:56:33 nas4free kernel: uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
Jan 20 10:56:33 nas4free kernel: uhub1: 2 ports with 2 removable, self powered
Jan 20 10:56:33 nas4free kernel: uhub2: 2 ports with 2 removable, self powered
Jan 20 10:56:33 nas4free kernel: uhub0: 21 ports with 21 removable, self powered
Jan 20 10:56:33 nas4free kernel: usb_alloc_device: device init 2 failed (USB_ERR_IOERROR, ignored)
Jan 20 10:56:33 nas4free kernel: ugen0.2: <Unknown> at usbus0 (disconnected)
Jan 20 10:56:33 nas4free kernel: uhub_reattach_port: could not allocate new device
Jan 20 10:56:33 nas4free kernel: ugen1.2: <vendor 0x8087> at usbus1
Jan 20 10:56:33 nas4free kernel: uhub3: <vendor 0x8087 product 0x8008, class 9/0, rev 2.00/0.05, addr 2> on usbus1
Jan 20 10:56:33 nas4free kernel: ugen2.2: <vendor 0x8087> at usbus2
Jan 20 10:56:33 nas4free kernel: uhub4: <vendor 0x8087 product 0x8000, class 9/0, rev 2.00/0.05, addr 2> on usbus2
Jan 20 10:56:33 nas4free kernel: uhub3: 6 ports with 6 removable, self powered
Jan 20 10:56:33 nas4free kernel: uhub4: 8 ports with 8 removable, self powered
Jan 20 10:56:33 nas4free kernel: usb_alloc_device: device init 2 failed (USB_ERR_IOERROR, ignored)
Jan 20 10:56:33 nas4free kernel: ugen0.2: <Unknown> at usbus0 (disconnected)
Jan 20 10:56:33 nas4free kernel: uhub_reattach_port: could not allocate new device
Jan 20 10:56:33 nas4free kernel: usb_alloc_device: device init 2 failed (USB_ERR_IOERROR, ignored)
Jan 20 10:56:33 nas4free kernel: ugen0.2: <Unknown> at usbus0 (disconnected)
Jan 20 10:56:33 nas4free kernel: uhub_reattach_port: could not allocate new device
Jan 20 10:56:33 nas4free kernel: usb_alloc_device: device init 2 failed (USB_ERR_IOERROR, ignored)
Jan 20 10:56:33 nas4free kernel: ugen0.2: <Unknown> at usbus0 (disconnected)
Jan 20 10:56:33 nas4free kernel: uhub_reattach_port: could not allocate new device
Jan 20 10:56:33 nas4free kernel: ada0 at ahcich2 bus 0 scbus0 target 0 lun 0
Jan 20 10:56:33 nas4free kernel: ada0: <ST4000VN000-1H4168 SC43> ATA-9 SATA 3.x device
Jan 20 10:56:33 nas4free kernel: ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
Jan 20 10:56:33 nas4free kernel: ada0: Command Queueing enabled
Jan 20 10:56:33 nas4free kernel: ada0: 3815447MB (7814037168 512 byte sectors: 16H 63S/T 16383C)
Jan 20 10:56:33 nas4free kernel: ada0: Previously was known as ad4
Jan 20 10:56:33 nas4free kernel: ada1 at ahcich3 bus 0 scbus1 target 0 lun 0
Jan 20 10:56:33 nas4free kernel: ada1: <ST4000VN000-1H4168 SC43> ATA-9 SATA 3.x device
Jan 20 10:56:33 nas4free kernel: ada1: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
Jan 20 10:56:33 nas4free kernel: ada1: Command Queueing enabled
Jan 20 10:56:33 nas4free kernel: ada1: 3815447MB (7814037168 512 byte sectors: 16H 63S/T 16383C)
Jan 20 10:56:33 nas4free kernel: ada1: Previously was known as ad6
Jan 20 10:56:33 nas4free kernel: ada2 at ahcich4 bus 0 scbus2 target 0 lun 0
Jan 20 10:56:33 nas4free kernel: ada2: <ST4000VN000-1H4168 SC43> ATA-9 SATA 3.x device
Jan 20 10:56:33 nas4free kernel: ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
Jan 20 10:56:33 nas4free kernel: ada2: Command Queueing enabled
Jan 20 10:56:33 nas4free kernel: ada2: 3815447MB (7814037168 512 byte sectors: 16H 63S/T 16383C)
Jan 20 10:56:33 nas4free kernel: ada2: Previously was known as ad8
Jan 20 10:56:33 nas4free kernel: ada3 at ahcich5 bus 0 scbus3 target 0 lun 0
Jan 20 10:56:33 nas4free kernel: ada3: <WDC WD10EADS-00L5B1 01.01A01> ATA-8 SATA 2.x device
Jan 20 10:56:33 nas4free kernel: ada3: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
Jan 20 10:56:33 nas4free kernel: ada3: Command Queueing enabled
Jan 20 10:56:33 nas4free kernel: ada3: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
Jan 20 10:56:33 nas4free kernel: ada3: Previously was known as ad10
Jan 20 10:56:33 nas4free kernel: SMP: AP CPU #1 Launched!
Jan 20 10:56:33 nas4free kernel: SMP: AP CPU #3 Launched!
Jan 20 10:56:33 nas4free kernel: SMP: AP CPU #2 Launched!
Jan 20 10:56:33 nas4free kernel: Timecounter "TSC-low" frequency 1699542236 Hz quality 1000
Jan 20 10:56:33 nas4free kernel: Trying to mount root from ufs:/dev/md0 []...
Jan 20 10:56:33 nas4free lighttpd[1966]: (log.c.166) server started 
Jan 20 10:56:34 nas4free login: login on ttyv0 as root
Jan 20 10:56:37 nas4free kernel: em0: link state changed to UP
Jan 20 11:01:11 nas4free login: login on ttyv0 as root
Jan 20 11:01:33 nas4free kernel: usb_alloc_device: device init 2 failed (USB_ERR_IOERROR, ignored)
Jan 20 11:01:33 nas4free kernel: ugen0.2: <Unknown> at usbus0 (disconnected)
Jan 20 11:01:33 nas4free kernel: uhub_reattach_port: could not allocate new device
Jan 20 11:01:49 nas4free kernel: usb_alloc_device: device init 2 failed (USB_ERR_IOERROR, ignored)
Jan 20 11:01:49 nas4free kernel: ugen0.2: <Unknown> at usbus0 (disconnected)
Jan 20 11:01:49 nas4free kernel: uhub_reattach_port: could not allocate new device
Jan 20 11:01:58 nas4free kernel: usb_alloc_device: device init 2 failed (USB_ERR_IOERROR, ignored)
Jan 20 11:01:58 nas4free kernel: ugen0.2: <Unknown> at usbus0 (disconnected)
Jan 20 11:01:58 nas4free kernel: uhub_reattach_port: could not allocate new device
Jan 20 11:02:25 nas4free kernel: usb_alloc_device: device init 2 failed (USB_ERR_IOERROR, ignored)
Jan 20 11:02:25 nas4free kernel: ugen0.2: <Unknown> at usbus0 (disconnected)
Jan 20 11:02:25 nas4free kernel: uhub_reattach_port: could not allocate new device
Jan 20 11:02:39 nas4free kernel: usb_alloc_device: device init 2 failed (USB_ERR_IOERROR, ignored)
Jan 20 11:02:39 nas4free kernel: ugen0.2: <Unknown> at usbus0 (disconnected)
Jan 20 11:02:39 nas4free kernel: uhub_reattach_port: could not allocate new device
Jan 20 11:05:34 nas4free login: login on ttyv0 as root
Jan 20 11:05:43 nas4free root: rcconf service executed
Jan 20 11:05:43 nas4free root: netif service started
Jan 20 11:06:27 nas4free root: rcconf service executed
Jan 20 11:06:27 nas4free root: netif service restarted
Jan 20 11:06:27 nas4free kernel: em0: link state changed to DOWN
Jan 20 11:06:27 nas4free root: routing service restarted
Jan 20 11:06:27 nas4free root: resolv service restarted
Jan 20 11:06:27 nas4free lighttpd[1966]: (server.c.1546) server stopped by UID = 0 PID = 4568 
Jan 20 11:06:28 nas4free lighttpd[4621]: (log.c.166) server started 
Jan 20 11:06:28 nas4free root: lighttpd service restarted
Jan 20 11:06:31 nas4free kernel: em0: link state changed to UP
Jan 20 11:10:19 nas4free lighttpd[4621]: (connections.c.137) (warning) close: 7 Connection reset by peer 
Jan 20 11:10:41 nas4free root: sshd service started
Jan 20 11:10:41 nas4free root: mdnsresponder service restarted

filius27

Re: No USB after NAS4Free boot

Posted: 24 Jan 2014 00:17
by mosiac
I too experiencing the same issue. I'm using a MSI B85i board and none of my USB devices work when Free4NAS loads up. I am using a PS/2 keyboard and that works. I get this error message when I insert a usb device : usb_alloc_device: device init 2 failed (USB_ERR_IOERROR, ignored)

Update : Okay for some reason it works fine if I plug usb devices into the USB 3.0 ports. Go figure...lol :lol:

Re: No USB after NAS4Free boot

Posted: 24 Jan 2014 07:39
by alexey123
If you have USB2 and USB3 devices mutually please disable on bios XHCI mode and use USB2
Image

Re: No USB after NAS4Free boot

Posted: 24 Jan 2014 12:03
by martl
in my DH87RL Bios there is no XHCI Option.
Only 'USB legacy'

Re: No USB after NAS4Free boot

Posted: 24 Jan 2014 12:06
by alexey123
Please post result

Code: Select all

dmesg

Re: No USB after NAS4Free boot

Posted: 25 Jan 2014 10:08
by dimko
Hello.
I've a similar problem with filius27
Unable to open configuration file /etc/hast.conf
No such file or directory
link /var/etc/hast.conf empty (no hast.conf)
My hardware:
Motherboard - Intel® Desktop Board D2700DC
Memory - Samsung 2x2048 DDR3
HDD - WDred 2x3Tb
USB Flash - SanDisk 16Gb for system.

I boot Nas4free 9.2.0.1.943 from usb
Until the prompt
'Welcome to NAS4Free
1. Boot NAS4Free in Normal Mode
2.
..
9. Install/Upgrade (Enter Number)

In the next window I select any position
1. Install Embedded...
2. Install Embedded...
3. Install Full...
4. ...
and get answer:
Unable to open configuration file /etc/hast.conf
Try ...
No detected CDROM or USB

What's the problem?

When I installed and used NAS4Free-9.1.0.1.847
I didn't have any problems.

Re: No USB after NAS4Free boot

Posted: 25 Jan 2014 11:28
by lux
@ dimko

did you get explicit USB version?? - other than LiveUSB Version will not install from USB-Stick...! ;)

http://sourceforge.net/projects/nas4fre ... g/download

the above LiveUSB.img Version works for me

write to USB Stick with cmdline-tool physdiskwrite ( http://m0n0.ch/wall/physdiskwrite.php ) under Win7

*warning* such tools as YUMI to write the whole .iso into Multi-Boot (for booting different .iso) on USB will not work - i have tried with no success

**/EDIT**

seems to be USB3 problem?? could it be? in german thread i found this:

viewtopic.php?f=29&t=5893
filius27 wrote: ...
Einfach in die /boot/loader.conf folgende Zeile eintragen:

Code: Select all

hw.usb.xhci.xhci_port_route=-1
...
Filius27 ;)
add the above code into /boot/loader.conf

Re: No USB after NAS4Free boot

Posted: 25 Jan 2014 17:50
by dimko
Thanks @ lux
I found the problem.
I had a bad flash drive ))
All times are UTC+01:00
Page 1 of 1

Powered by phpBB® Forum Software © phpBB Limited