My disks are listed in the DISK-MANAGEMENT section, but I am NOT able to select them in DISK-MANAGEMENT-DISKS-ADD.
They just don't show up in the pull-down menu. Only the CD-ROM shows up.
Any ideas.
BTW: The disks are WD Green 500 GB.
This is the old XigmaNAS forum in read only mode,
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
Cannot select disks
-
armandh
- Advanced User
- Posts: 398
- Joined: 23 Jun 2012 04:15
- Location: St Louis County Missouri USA
- Status: Offline
Re: Cannot select disks
disks that have been added previously and not been cleaned of their flags wont show
try partition and formatting ext3 then delete partition for a clean drive
but if you wish to save data .... import
try partition and formatting ext3 then delete partition for a clean drive
but if you wish to save data .... import
4 thread 3300 Mhz Intel i3, 1 TB ZFS mirror, available RAM 7.823 Gb, 64 bit NAS4Free 9.1.0.1 rev 573 [88 watts, 48 Mbps]
2 thread 1600 Mhz atom/ion, 1 TB ZFS mirror, available RAM 3.083 Gb, 64 bit NAS4Free-9.1.0.1 rev 573 [27 watts, 35 Mbps]
2 thread 3900 Mhz AMD A6-6400K, 2 TB ZFS Mirror, available RAM 7.557 Gb, 64 bit Nas4Free 9.3.0.2.1771 [89 watts, 68 Mbps]
2 thread 1600 Mhz atom/ion, 1 TB ZFS mirror, available RAM 3.083 Gb, 64 bit NAS4Free-9.1.0.1 rev 573 [27 watts, 35 Mbps]
2 thread 3900 Mhz AMD A6-6400K, 2 TB ZFS Mirror, available RAM 7.557 Gb, 64 bit Nas4Free 9.3.0.2.1771 [89 watts, 68 Mbps]
-
Pilsener
- NewUser
- Posts: 2
- Joined: 11 May 2014 23:22
- Status: Offline
Re: Cannot select disks
It suddenly worked....dunno how.
Now I only need to figure out how to setup software RAID 0.
This thing could really need some wizards.
Now I only need to figure out how to setup software RAID 0.
This thing could really need some wizards.
-
crowi
- Forum Moderator
- Posts: 1176
- Joined: 21 Feb 2013 16:18
- Location: Munich, Germany
- Status: Offline
Re: Cannot select disks
go to Disks|Software RAID|RAID0|Management and hit the '+' button
NAS 1: Milchkuh: Asrock C2550D4I, Intel Avoton C2550 Quad-Core, 16GB DDR3 ECC, 5x3TB WD Red RaidZ1 +60 GB SSD for ZIL/L2ARC, APC-Back UPS 350 CS, NAS4Free 11.0.0.4.3460 embedded
NAS 2: Backup: HP N54L, 8 GB ECC RAM, 4x4 TB WD Red, RaidZ1, NAS4Free 11.0.0.4.3460 embedded
NAS 3: Office: HP N54L, 8 GB ECC RAM, 2x3 TB WD Red, ZFS Mirror, APC-Back UPS 350 CS NAS4Free 11.0.0.4.3460 embedded
NAS 2: Backup: HP N54L, 8 GB ECC RAM, 4x4 TB WD Red, RaidZ1, NAS4Free 11.0.0.4.3460 embedded
NAS 3: Office: HP N54L, 8 GB ECC RAM, 2x3 TB WD Red, ZFS Mirror, APC-Back UPS 350 CS NAS4Free 11.0.0.4.3460 embedded