hi all,
I had the same problem but I didn't understand the solution.
I've a full install on a USB key and after many black outs in a few hours I saw that I've on line FTP, SMB, FUPPES, DynDNS and SSH services, but all my web gui services (Trasmission and the NAS4FREE's webguis) doesn't works. Only FUPPES's webgui works.
It says that a configuration missing and I don't see the classic menus of 8 chioces (set admin password, set LAN interfaces, reboot, shut down, etc...).
How can I fix it?
This is the old XigmaNAS forum in read only mode,
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
configuration missing
-
leo1986pc
- Starter
- Posts: 24
- Joined: 05 May 2014 13:43
- Location: Reggio Emilia, Italy
- Status: Offline
-
armandh
- Advanced User
- Posts: 398
- Joined: 23 Jun 2012 04:15
- Location: St Louis County Missouri USA
- Status: Offline
configuration missing
consumer USB flash drives are NOT suitable for a full install !!!
write wear will quickly kill the USB flash
they are OK for only the embedded OS where they just store and load the OS to RAM on boot-up.
write wear will quickly kill the USB flash
they are OK for only the embedded OS where they just store and load the OS to RAM on boot-up.
4 thread 3300 Mhz Intel i3, 1 TB ZFS mirror, available RAM 7.823 Gb, 64 bit NAS4Free 9.1.0.1 rev 573 [88 watts, 48 Mbps]
2 thread 1600 Mhz atom/ion, 1 TB ZFS mirror, available RAM 3.083 Gb, 64 bit NAS4Free-9.1.0.1 rev 573 [27 watts, 35 Mbps]
2 thread 3900 Mhz AMD A6-6400K, 2 TB ZFS Mirror, available RAM 7.557 Gb, 64 bit Nas4Free 9.3.0.2.1771 [89 watts, 68 Mbps]
2 thread 1600 Mhz atom/ion, 1 TB ZFS mirror, available RAM 3.083 Gb, 64 bit NAS4Free-9.1.0.1 rev 573 [27 watts, 35 Mbps]
2 thread 3900 Mhz AMD A6-6400K, 2 TB ZFS Mirror, available RAM 7.557 Gb, 64 bit Nas4Free 9.3.0.2.1771 [89 watts, 68 Mbps]
-
leo1986pc
- Starter
- Posts: 24
- Joined: 05 May 2014 13:43
- Location: Reggio Emilia, Italy
- Status: Offline
Re: [SOLVED] Error can't access webgui / Fix damaged system.
And how can I solve the problem without loss my data?
-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: [SOLVED] Error can't access webgui / Fix damaged system.
please do not open old threads. open your own thread for your problem. otherwise it gets confusing.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.