Page 1 of 1
Hilfe was bedeutet das?
Posted: 20 Jul 2015 05:58
by seller
Hilfe was geht hier ab, das NAS ist pötzlich extrem zäh und kopieren dauert ewig.....
LOG-DATEI
Code: Select all
Datum & Zeit Benutzer Ereignis
Jul 19 16:57:23 nas4free-2 kernel: (ada2:ata3:0:1:0): Error 5, Retries exhausted
Jul 19 16:57:23 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 c8 73 4d 59 59 00 00 58 00
Jul 19 16:57:23 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:57:23 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:57:23 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 c8 73 4d 40 59 00 00 00 58 00
Jul 19 16:57:18 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:57:18 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 c8 73 4d 59 59 00 00 58 00
Jul 19 16:57:18 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:57:18 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:57:18 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 c8 73 4d 40 59 00 00 00 58 00
Jul 19 16:57:14 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:57:14 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 c8 73 4d 59 59 00 00 58 00
Jul 19 16:57:14 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:57:14 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:57:14 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 c8 73 4d 40 59 00 00 00 58 00
Jul 19 16:57:06 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:57:06 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 c8 73 4d 59 59 00 00 58 00
Jul 19 16:57:06 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:57:06 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:57:06 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 c8 73 4d 40 59 00 00 00 58 00
Jul 19 16:57:02 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:57:02 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 c8 73 4d 59 59 00 00 58 00
Jul 19 16:57:02 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:57:02 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:57:02 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 c8 73 4d 40 59 00 00 00 58 00
Jul 19 16:54:29 nas4free-2 kernel: (ada2:ata3:0:1:0): Error 5, Retries exhausted
Jul 19 16:54:29 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a8 d2 de 65 65 00 00 08 00
Jul 19 16:54:29 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:54:29 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:54:29 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a8 d2 de 40 65 00 00 00 08 00
Jul 19 16:54:25 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:54:25 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a8 d2 de 65 65 00 00 08 00
Jul 19 16:54:25 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:54:25 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:54:25 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a8 d2 de 40 65 00 00 00 08 00
Jul 19 16:54:21 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:54:21 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a8 d2 de 65 65 00 00 08 00
Jul 19 16:54:21 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:54:21 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:54:21 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a8 d2 de 40 65 00 00 00 08 00
Jul 19 16:54:18 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:54:18 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a8 d2 de 65 65 00 00 08 00
Jul 19 16:54:18 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:54:18 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:54:18 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a8 d2 de 40 65 00 00 00 08 00
Jul 19 16:54:14 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:54:14 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a8 d2 de 65 65 00 00 08 00
Jul 19 16:54:14 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:54:14 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:54:14 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a8 d2 de 40 65 00 00 00 08 00
Jul 19 16:50:50 nas4free-2 kernel: (ada2:ata3:0:1:0): Error 5, Retries exhausted
Jul 19 16:50:50 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a8 92 4c 59 59 00 00 08 00
Jul 19 16:50:50 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:50:50 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:50:50 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a8 92 4c 40 59 00 00 00 08 00
Jul 19 16:50:46 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:50:46 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a8 92 4c 59 59 00 00 08 00
Jul 19 16:50:46 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:50:46 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:50:46 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a8 92 4c 40 59 00 00 00 08 00
Jul 19 16:50:42 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:50:42 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a8 92 4c 59 59 00 00 08 00
Jul 19 16:50:42 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:50:42 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:50:42 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a8 92 4c 40 59 00 00 00 08 00
Jul 19 16:50:38 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:50:38 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a8 92 4c 59 59 00 00 08 00
Jul 19 16:50:38 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:50:38 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:50:38 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a8 92 4c 40 59 00 00 00 08 00
Jul 19 16:50:35 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:50:35 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a8 92 4c 59 59 00 00 08 00
Jul 19 16:50:35 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:50:35 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:50:35 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a8 92 4c 40 59 00 00 00 08 00
Jul 19 16:50:31 nas4free-2 kernel: (ada2:ata3:0:1:0): Error 5, Retries exhausted
Jul 19 16:50:31 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a0 92 4c 59 59 00 00 08 00
Jul 19 16:50:31 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:50:31 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:50:31 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a0 92 4c 40 59 00 00 00 08 00
Jul 19 16:50:27 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:50:27 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a0 92 4c 59 59 00 00 08 00
Jul 19 16:50:27 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:50:27 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:50:27 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a0 92 4c 40 59 00 00 00 08 00
Jul 19 16:50:23 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:50:23 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a0 92 4c 59 59 00 00 08 00
Jul 19 16:50:23 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:50:23 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:50:23 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a0 92 4c 40 59 00 00 00 08 00
Jul 19 16:50:19 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:50:19 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a0 92 4c 59 59 00 00 08 00
Jul 19 16:50:19 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:50:19 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:50:19 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a0 92 4c 40 59 00 00 00 08 00
Jul 19 16:50:15 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:50:15 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 a0 92 4c 59 59 00 00 08 00
Jul 19 16:50:15 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:50:15 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:50:15 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 a0 92 4c 40 59 00 00 00 08 00
Jul 19 16:50:11 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:50:11 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 98 92 4c 59 59 00 00 08 00
Jul 19 16:50:11 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:50:11 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:50:11 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 98 92 4c 40 59 00 00 00 08 00
Jul 19 16:49:15 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:49:15 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 68 6b e2 58 58 00 00 08 00
Jul 19 16:49:15 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:49:15 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:49:15 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 68 6b e2 40 58 00 00 00 08 00
Jul 19 16:49:11 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:49:11 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 68 6b e2 58 58 00 00 08 00
Jul 19 16:49:11 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:49:11 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:49:11 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 68 6b e2 40 58 00 00 00 08 00
Jul 19 16:49:07 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:49:07 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 68 6b e2 58 58 00 00 08 00
Jul 19 16:49:07 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:49:07 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:49:07 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 68 6b e2 40 58 00 00 00 08 00
Jul 19 16:47:41 nas4free-2 kernel: (ada2:ata3:0:1:0): Error 5, Retries exhausted
Jul 19 16:47:41 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 90 cf 20 6a 6a 00 00 08 00
Jul 19 16:47:41 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:47:41 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:47:41 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 90 cf 20 40 6a 00 00 00 08 00
Jul 19 16:47:37 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:47:37 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 90 cf 20 6a 6a 00 00 08 00
Jul 19 16:47:37 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:47:37 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:47:37 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 90 cf 20 40 6a 00 00 00 08 00
Jul 19 16:47:34 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:47:34 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 90 cf 20 6a 6a 00 00 08 00
Jul 19 16:47:34 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:47:34 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:47:34 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 90 cf 20 40 6a 00 00 00 08 00
Jul 19 16:47:30 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:47:30 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 90 cf 20 6a 6a 00 00 08 00
Jul 19 16:47:30 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:47:30 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:47:30 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 90 cf 20 40 6a 00 00 00 08 00
Jul 19 16:47:26 nas4free-2 kernel: (ada2:ata3:0:1:0): Retrying command
Jul 19 16:47:26 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 90 cf 20 6a 6a 00 00 08 00
Jul 19 16:47:26 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:47:26 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:47:26 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 90 cf 20 40 6a 00 00 00 08 00
Jul 19 16:47:22 nas4free-2 kernel: (ada2:ata3:0:1:0): Error 5, Retries exhausted
Jul 19 16:47:22 nas4free-2 kernel: (ada2:ata3:0:1:0): RES: 51 40 10 ce 20 6a 6a 00 00 08 00
Jul 19 16:47:22 nas4free-2 kernel: (ada2:ata3:0:1:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Jul 19 16:47:22 nas4free-2 kernel: (ada2:ata3:0:1:0): CAM status: ATA Status Error
Jul 19 16:47:22 nas4free-2 kernel: (ada2:ata3:0:1:0): READ_DMA48. ACB: 25 00 10 ce 20 40 6a 00 00 00 08 00
Re: Hilfe was bedeutet das?
Posted: 20 Jul 2015 06:52
by Princo
Dein System hat den ganzen Speicher genutzt,
müsste jetzt dringend swappen,
kann nicht swappen,
weil du kein Swap-Device eingerichtet hast.
Daher fängt das System an, eigenständig Prozesse zu killen,
und dazu gehört leider auch der ZFS-Prozeß.
Abhilfe: Swap-Gerät einrichten.
Mehr RAM hilft an dieser Stelle kaum.
Grüße
Princo
Re: Hilfe was bedeutet das?
Posted: 20 Jul 2015 08:30
by b0ssman
Poste auch mal deine smart Werte aller Platten.
Sent from my iPhone using Tapatalk
Re: Hilfe was bedeutet das?
Posted: 20 Jul 2015 15:20
by seller
@ bossman
meinst Du das ?
System zur Selbstüberwachung, Analyse und Statusmeldung Freigeben
Überprüfungsintervall
Setzt das Interval der Überprüfungen auf N Sekunden. Der erlaubte Minimalwert ist 10.
Expertenmodus
Nie - Das Gerät wird immer überprüft, unabhängig vom Energiesparzustand. Eine abgeschaltete Festplatte wird dann für die Überprüfung hochgefahren.
Sleep - Überprüfe das Gerät es sei denn es befindet sich im SLEEP Modus.
Bereitsschaftmodus - die Einheit überprüfen, solange diese sich nicht im Ruhe- oder Bereitschaftsmodus befindet. In diesen Modi drehen die Laufwerke nicht, wenn Sie also sicherstellen wollen, dass bei einem Mobilrechner die Festplatten bei jeden Zugriff hochdrehen, dann ist das wahrscheinlich dies, was Sie haben wollen.
Idle - Überprüfe das Gerät außer es ist im SLEEP, STANDBY, oder IDLE Modus. Im IDLE Zustand laufen viele Festplatten weiter was eventuell unerwünscht ist.
Temperaturüberwachung
Differenz °C
Benachrichtigen, falls sich die Temperatur um mindestens N Grad Celsius seit der letzen Benachrichtigung verändert hat. Auf 0 setzen zum Deaktivieren dieser Benachrichtigung.
Zur Information °C
Melden wenn die Termperatur N °C erreicht oder überschreitet. 0 unterbindet die Meldung.
Kritisch °C
Melden wenn die Termperatur N °C erreicht oder überschreitet. 0 unterbindet die Meldung.
Geplante Selbst-Tests
Geplante Selbst-Tests
Festplatte Typ Beschreibung
/dev/ada4 Short Self-Test Selbsttest bearbeiten Selbsttest löschen
/dev/ada3 Short Self-Test Selbsttest bearbeiten Selbsttest löschen
/dev/ada2 Short Self-Test Selbsttest bearbeiten Selbsttest löschen
/dev/ada1 Short Self-Test Selbsttest bearbeiten Selbsttest löschen
Selbsttest hinzufügen Alle Selbsttests löschen
Zusätzliche planmäßige Selbsttests hinzufügen.
E-Mail Bericht Aktivieren
An E-Mail-Adresse
E-Mail Adresse des Empfängers. Semikolon getrennte Liste von E-Mail Adressen.
Test E-Mail Sende eine TEST-Warnung als E-Mail nach dem Start.
Re: Hilfe was bedeutet das?
Posted: 20 Jul 2015 15:50
by b0ssman
nein ich meine die infos aus
Diagnostics|Information|S.M.A.R.T.
Re: Hilfe was bedeutet das?
Posted: 20 Jul 2015 17:52
by seller
@bossMan
hier....
Code: Select all
Gerät /dev/ada0 - SAMSUNG HD203WI 1AN10003
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F3 EG
Device Model: SAMSUNG HD203WI
Serial Number: S2ACJ1AZ800553
LU WWN Device Id: 5 0024e9 003ed6ac6
Firmware Version: 1AN10003
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Mon Jul 20 17:47:59 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (25800) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 430) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 11
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 060 058 025 Pre-fail Always - 12344
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 280
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 33041
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 252 252 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 343
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 283
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 063 057 000 Old_age Always - 37 (Min/Max 16/43)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 487
223 Load_Retry_Count 0x0032 252 252 000 Old_age Always - 0
225 Load_Cycle_Count 0x0032 086 086 000 Old_age Always - 146534
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Gerät /dev/ada1 - SAMSUNG HD203WI 1AN10003
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F3 EG
Device Model: SAMSUNG HD203WI
Serial Number: S2ACJ1AZ800550
LU WWN Device Id: 5 0024e9 003ed688e
Firmware Version: 1AN10003
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Mon Jul 20 17:48:01 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (25260) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 421) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 1
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 060 057 025 Pre-fail Always - 12374
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 290
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 33036
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 252 252 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 338
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 846
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 064 056 000 Old_age Always - 34 (Min/Max 17/44)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x002a 001 001 000 Old_age Always - 572977
223 Load_Retry_Count 0x0032 252 252 000 Old_age Always - 0
225 Load_Cycle_Count 0x0032 086 086 000 Old_age Always - 144738
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Gerät /dev/ada2 - TOSHIBA DT01ACA200 MX4OABB0
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 3.5" HDD DT01ACA...
Device Model: TOSHIBA DT01ACA200
Serial Number: 13B453MAS
LU WWN Device Id: 5 000039 ff3c1e4b1
Firmware Version: MX4OABB0
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon Jul 20 17:48:02 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (15969) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 267) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 086 086 016 Pre-fail Always - 7208960
2 Throughput_Performance 0x0005 138 138 054 Pre-fail Offline - 76
3 Spin_Up_Time 0x0007 127 127 024 Pre-fail Always - 298 (Average 298)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 224
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 1648
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 124 124 020 Pre-fail Offline - 33
9 Power_On_Hours 0x0012 098 098 000 Old_age Always - 16121
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 224
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 735
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 735
194 Temperature_Celsius 0x0002 146 146 000 Old_age Always - 41 (Min/Max 19/44)
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2947
197 Current_Pending_Sector 0x0022 001 001 000 Old_age Always - 5992
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 31
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 817 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 817 occurred at disk power-on lifetime: 16121 hours (671 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 40 a2 dc 09 Error: UNC 8 sectors at LBA = 0x09dca240 = 165454400
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 40 a2 dc 40 00 1d+07:45:46.475 READ DMA EXT
25 00 08 40 a2 dc 40 00 1d+07:45:42.956 READ DMA EXT
25 00 08 40 a2 dc 40 00 1d+07:45:39.246 READ DMA EXT
25 00 08 40 a2 dc 40 00 1d+07:45:35.553 READ DMA EXT
25 00 08 40 a2 dc 40 00 1d+07:45:32.214 READ DMA EXT
Error 816 occurred at disk power-on lifetime: 16121 hours (671 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 40 a2 dc 09 Error: UNC 8 sectors at LBA = 0x09dca240 = 165454400
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 40 a2 dc 40 00 1d+07:45:42.956 READ DMA EXT
25 00 08 40 a2 dc 40 00 1d+07:45:39.246 READ DMA EXT
25 00 08 40 a2 dc 40 00 1d+07:45:35.553 READ DMA EXT
25 00 08 40 a2 dc 40 00 1d+07:45:32.214 READ DMA EXT
ea 00 00 00 00 00 40 00 1d+07:21:28.778 FLUSH CACHE EXT
Error 815 occurred at disk power-on lifetime: 16121 hours (671 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 40 a2 dc 09 Error: UNC 8 sectors at LBA = 0x09dca240 = 165454400
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 40 a2 dc 40 00 1d+07:45:39.246 READ DMA EXT
25 00 08 40 a2 dc 40 00 1d+07:45:35.553 READ DMA EXT
25 00 08 40 a2 dc 40 00 1d+07:45:32.214 READ DMA EXT
ea 00 00 00 00 00 40 00 1d+07:21:28.778 FLUSH CACHE EXT
35 00 08 28 87 e0 40 00 1d+07:21:28.744 WRITE DMA EXT
Error 814 occurred at disk power-on lifetime: 16121 hours (671 days + 17 hours)
When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 40 a2 dc 09 Error: UNC 8 sectors at LBA = 0x09dca240 = 165454400
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 40 a2 dc 40 00 1d+07:45:35.553 READ DMA EXT
25 00 08 40 a2 dc 40 00 1d+07:45:32.214 READ DMA EXT
ea 00 00 00 00 00 40 00 1d+07:21:28.778 FLUSH CACHE EXT
35 00 08 28 87 e0 40 00 1d+07:21:28.744 WRITE DMA EXT
35 00 08 28 85 e0 40 00 1d+07:21:28.717 WRITE DMA EXT
Error 813 occurred at disk power-on lifetime: 16121 hours (671 days + 17 hours)
When the command that caused the error occurred, the device was doing SMART Offline or Self-test.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 40 a2 dc 09 Error: UNC 8 sectors at LBA = 0x09dca240 = 165454400
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 40 a2 dc 40 00 1d+07:45:32.214 READ DMA EXT
ea 00 00 00 00 00 40 00 1d+07:21:28.778 FLUSH CACHE EXT
35 00 08 28 87 e0 40 00 1d+07:21:28.744 WRITE DMA EXT
35 00 08 28 85 e0 40 00 1d+07:21:28.717 WRITE DMA EXT
ca 00 08 28 03 00 e0 00 1d+07:21:28.716 WRITE DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Gerät /dev/ada3 - TOSHIBA DT01ACA200 MX4OABB0
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 3.5" HDD DT01ACA...
Device Model: TOSHIBA DT01ACA200
Serial Number: 13B9ARBGS
LU WWN Device Id: 5 000039 ff3c43f96
Firmware Version: MX4OABB0
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon Jul 20 17:48:03 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (15300) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 139 139 054 Pre-fail Offline - 71
3 Spin_Up_Time 0x0007 131 131 024 Pre-fail Always - 290 (Average 290)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 223
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 126 126 020 Pre-fail Offline - 32
9 Power_On_Hours 0x0012 098 098 000 Old_age Always - 16123
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 223
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 741
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 741
194 Temperature_Celsius 0x0002 166 166 000 Old_age Always - 36 (Min/Max 20/43)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Gerät /dev/da0 - USB2.0 FlashDisk 0.00
/dev/da0: Unknown USB bridge [0x1307:0x0165 (0x100)]
Please specify device type with the -d option.
Use smartctl -h to get a usage summary
Gruß
Seller
Re: Hilfe was bedeutet das?
Posted: 20 Jul 2015 19:30
by b0ssman
ada ist fast tot. die platte musst du SOFORT ersetzen
Re: Hilfe was bedeutet das?
Posted: 20 Jul 2015 19:56
by seller
Hallo BossMan,
UUUIIII!!!! jetzt bin ich etwas geschockt, vor ein zwei Wochen noch nen SCrub gemacht und da war alles noch ok .
ist es die ADA0 die stirbt?
was kann ich wie tun?
klar als erstes mal ne neue Platte her,ist bestellt.
und dann wohl am besten das Nas ausschalten und ruhen lassen bis die Platte das ist oder?
Kannst Du mir sagen wie ich die Hardware identifiziere, die die Grätsche macht, Du verstehst was ich meine?
Gruß Seller
Re: Hilfe was bedeutet das?
Posted: 20 Jul 2015 20:01
by b0ssman
ada2
1 Raw_Read_Error_Rate 0x000b 086 086 016 Pre-fail Always - 7208960
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 1648
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2947
197 Current_Pending_Sector 0x0022 001 001 000 Old_age Always - 5992
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 31
Re: Hilfe was bedeutet das?
Posted: 20 Jul 2015 20:06
by seller
was meinst Du soll ich abschalten oder ?
Re: Hilfe was bedeutet das?
Posted: 20 Jul 2015 20:16
by crowi
kommt darauf an wie Du Dein System aufgesetzt (RAID / RAIDZx etc) hast und wie aktuell Deine Backups sind. Am besten abschalten, neue Platte rein und RAID oder Pool wiederherstellen.
Re: Hilfe was bedeutet das?
Posted: 20 Jul 2015 20:29
by seller
hi Bossmann
ich habe alle Daten doppelt, das Nas ist meine Datensicherung der Arbeitstiere und zweier Laptops
ist das die gewünschte Info ?
NAS_raidz1_0 raidz1 NAS /dev/ada1, /dev/ada0, /dev/ada2, /dev/ada3
Re: Hilfe was bedeutet das?
Posted: 20 Jul 2015 21:13
by b0ssman
wenn du derzeit keine platte zum wechseln hast schalte den server ab
Re: Hilfe was bedeutet das?
Posted: 20 Jul 2015 21:14
by seller
so NAS ist aus, warte auf die Festplatte, melde mich bei Eintreffen (spätesten 24.07.)wieder.
Erstmal vielen Dank für die schnelle Hilfe.
Gruß
Seller
Re: Hilfe was bedeutet das?
Posted: 21 Jul 2015 00:37
by Princo
Hallo seller,
Entschuldige bitte meine falsche Fehlerdiagnose. Ich war steif und fest der Überzeugung, daß bei deiner Log-Datei verschiedene ada's gemeldet wurden, und das brachte mich auf das typische Swap-Problem.
Zum Glück hatte b0ssman den richtigen Riecher
Grüße
Princo
Re: Hilfe was bedeutet das?
Posted: 21 Jul 2015 17:23
by seller
Hallo Princo,
kein Grund für ne Entschuldigung....
Hauptsache der Fehler ist gefunden.
Und mit eurer Hilfe schaffe ich auch den Plattentausch.
Bis die Tage
Gruß
Seller