XigmaNAS

Hi,Sorry I'm not sure how to search for this question as all the terms I can think of are too generic - the search engine ignored some of them already.
I have one mirrored raid set in my system already, and I'd like to expand by adding a second raid set. Can I do this using one controller card - assuming there's enough ports on the card - or do I need a separate controller card for each raid set?

well you dont give much addition information.
but in general you can.

You're right. In retrospect, my question wasn't fair. I wasn't thinking that maybe some cards can and some can't
The controller is a Promise PDC40718. I picked it when I set up my system based on the fact that it's one the N4F hardware list.
I have 2 2TB mirrored drives in the system right now, and I've just added 2 more. My plan was to have a second set of drives, mirrored.
I'm having a bit of trouble at the moment because I'm having trouble keeping track of the drives as I don't wish to format either of the 2 that are in use.
Under Drives-Management, the config looks like this (sorry I couldn't figure out how to get Snip-it to paste a screen shot)

Device Device model Size Serial number Controller Controller model Standby time File system Status
ada0 WDC WD20EFRX-68AX9N0 1907730MB WD-WCC300363650 ata2 Promise PDC40718 SATA300 controller 10 Unknown or unformatted ONLINE
ada1 WDC WD20EFRX-68EUZN0 1907730MB WD-WCC4M0868843 ata3 Promise PDC40718 SATA300 controller Always on ZFS storage pool device ONLINE
ada2 WDC WD20EFRX-68EUZN0 1907730MB WD-WCC4M3170388 ata4 Promise PDC40718 SATA300 controller 10 ZFS storage pool device ONLINE
ada3 WDC WD20EFRX-68AX9N0 1907730MB WD-WMC300002637 ata5 Promise PDC40718 SATA300 controller Always on ZFS storage pool device ONLINE

What I see here is device ada0 and ada2 are the 2 new drives (because I set up the standby time to 10 minutes).
I was able to format the second drive - ada2, but for some reason the first drive doesn't show in the list of available drives to format. In fact, only 2 of the 4 drives show in the list - ada2 and ada3 (and da0 but I'm ignoring that one)

Any suggestions as to how I get the other 2 drives to show in the list?

The other thing I noticed, is that when I go to Information under the Diagnostics tab, I get the following table.
What I see here is the 2 new drives are now devices ada0 and ada3 (I assume they have gone to standby and are a 0 rpm). The other thing, I think, is the device models are 2 different sets, although the model numbers in the table above are also transposed.
What would be really nice here is if the description that I typed in for the new drives when I set them up under management would show in either of the tables. I am going to go write down the serial numbers of the drives when I get a few moments.....

Device Device model Description Size Serial number Rotation rate S.M.A.R.T. Controller Controller model
ada0 WDC WD20EFRX-68AX9N0 Western Digital Red (AF) 1907730MB WD-WCC300363650 n/a Available , Enabled ata2 Promise PDC40718
ada1 WDC WD20EFRX-68EUZN0 Western Digital Red (AF) 1907730MB WD-WCC4M0868843 5400 Available , Enabled ata3 Promise PDC40718
ada2 WDC WD20EFRX-68EUZN0 Western Digital Red (AF) 1907730MB WD-WCC4M3170388 5400 Available , Enabled ata4 Promise PDC40718
ada3 WDC WD20EFRX-68AX9N0 Western Digital Red (AF) 1907730MB WD-WMC300002637 n/a Available , Enabled ata5 Promise PDC40718

sync your zfs setup

ok, I must be daft. I don't see a "sync button". Is it one of the options on the management tab? It can't be "clear config and import disks" because that reports back that the disk I just formatted as unformatted. The wiki pages doesn't have much detail for troubleshooting.
Sorry

see
http://wiki.nas4free.org/doku.php?id=do ... ynchronize

Thank You. Drives formatted.
What was throwing me off was the new drives didn't show up on this page, so I didn't think the page was related.