Samsung hd204ui cam status ata status error
Posted: 02 Mar 2015 07:55
well there isn't much to add... Can anyone tell me if this disk is good or not?
$ smartctl -a /dev/ada1
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p9 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, http://www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F4 EG (AF)
Device Model: SAMSUNG HD204UI
Serial Number: S2H7J9BB311526
LU WWN Device Id: 5 0024e9 204ba670a
Firmware Version: 1AQ10001
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sun Mar 1 15:47:41 2015 CET
==> WARNING: Using smartmontools or hdparm with this
drive may result in data loss due to a firmware bug.
****** THIS DRIVE MAY OR MAY NOT BE AFFECTED! ******
Buggy and fixed firmware report same version number!
See the following web pages for details:
http://knowledge.seagate.com/articles/e ... Q/223571en
http://www.smartmontools.org/wiki/SamsungF4EGBadBlocks
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (20640) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 344) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 901
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 066 065 025 Pre-fail Always - 10345
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 401
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 259
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 252 252 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 539
181 Program_Fail_Cnt_Total 0x0022 100 100 000 Old_age Always - 61034
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 7133
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 064 064 000 Old_age Always - 22 (Min/Max 7/39)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 7
223 Load_Retry_Count 0x0032 252 252 000 Old_age Always - 0
225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 555
SMART Error Log Version: 1
ATA Error Count: 563 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 563 occurred at disk power-on lifetime: 258 hours (10 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 28 00 28 f1 e8 Error: UNC 40 sectors at LBA = 0x08f12800 = 150022144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 e8 28 f1 e8 02 00:00:00.425 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.420 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.415 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.410 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.405 READ DMA
Error 562 occurred at disk power-on lifetime: 258 hours (10 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 28 00 28 f1 e8 Error: UNC 40 sectors at LBA = 0x08f12800 = 150022144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 e8 28 f1 e8 02 00:00:00.420 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.415 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.410 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.405 READ DMA
35 00 40 e8 0d 32 40 02 00:00:00.404 WRITE DMA EXT
Error 561 occurred at disk power-on lifetime: 258 hours (10 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 28 00 28 f1 e8 Error: UNC 40 sectors at LBA = 0x08f12800 = 150022144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 e8 28 f1 e8 02 00:00:00.415 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.410 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.405 READ DMA
35 00 40 e8 0d 32 40 02 00:00:00.404 WRITE DMA EXT
35 00 40 68 0c 32 40 02 00:00:00.404 WRITE DMA EXT
Error 560 occurred at disk power-on lifetime: 258 hours (10 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 28 00 28 f1 e8 Error: UNC 40 sectors at LBA = 0x08f12800 = 150022144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 e8 28 f1 e8 02 00:00:00.410 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.405 READ DMA
35 00 40 e8 0d 32 40 02 00:00:00.404 WRITE DMA EXT
35 00 40 68 0c 32 40 02 00:00:00.404 WRITE DMA EXT
35 00 40 28 6e 31 40 02 00:00:00.404 WRITE DMA EXT
Error 559 occurred at disk power-on lifetime: 258 hours (10 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 28 00 28 f1 e8 Error: UNC 40 sectors at LBA = 0x08f12800 = 150022144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 e8 28 f1 e8 02 00:00:00.405 READ DMA
35 00 40 e8 0d 32 40 02 00:00:00.404 WRITE DMA EXT
35 00 40 68 0c 32 40 02 00:00:00.404 WRITE DMA EXT
35 00 40 28 6e 31 40 02 00:00:00.404 WRITE DMA EXT
ca 00 00 e8 78 05 e9 02 00:00:00.404 WRITE DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 259 124820848
# 2 Extended offline Aborted by host 90% 231 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed_read_failure [90% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
$ smartctl -a /dev/ada1
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p9 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, http://www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F4 EG (AF)
Device Model: SAMSUNG HD204UI
Serial Number: S2H7J9BB311526
LU WWN Device Id: 5 0024e9 204ba670a
Firmware Version: 1AQ10001
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sun Mar 1 15:47:41 2015 CET
==> WARNING: Using smartmontools or hdparm with this
drive may result in data loss due to a firmware bug.
****** THIS DRIVE MAY OR MAY NOT BE AFFECTED! ******
Buggy and fixed firmware report same version number!
See the following web pages for details:
http://knowledge.seagate.com/articles/e ... Q/223571en
http://www.smartmontools.org/wiki/SamsungF4EGBadBlocks
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (20640) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 344) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 901
2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0
3 Spin_Up_Time 0x0023 066 065 025 Pre-fail Always - 10345
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 401
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0
8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 259
10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 252 252 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 539
181 Program_Fail_Cnt_Total 0x0022 100 100 000 Old_age Always - 61034
191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 7133
192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0
194 Temperature_Celsius 0x0002 064 064 000 Old_age Always - 22 (Min/Max 7/39)
195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0
196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 7
223 Load_Retry_Count 0x0032 252 252 000 Old_age Always - 0
225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 555
SMART Error Log Version: 1
ATA Error Count: 563 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 563 occurred at disk power-on lifetime: 258 hours (10 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 28 00 28 f1 e8 Error: UNC 40 sectors at LBA = 0x08f12800 = 150022144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 e8 28 f1 e8 02 00:00:00.425 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.420 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.415 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.410 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.405 READ DMA
Error 562 occurred at disk power-on lifetime: 258 hours (10 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 28 00 28 f1 e8 Error: UNC 40 sectors at LBA = 0x08f12800 = 150022144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 e8 28 f1 e8 02 00:00:00.420 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.415 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.410 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.405 READ DMA
35 00 40 e8 0d 32 40 02 00:00:00.404 WRITE DMA EXT
Error 561 occurred at disk power-on lifetime: 258 hours (10 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 28 00 28 f1 e8 Error: UNC 40 sectors at LBA = 0x08f12800 = 150022144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 e8 28 f1 e8 02 00:00:00.415 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.410 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.405 READ DMA
35 00 40 e8 0d 32 40 02 00:00:00.404 WRITE DMA EXT
35 00 40 68 0c 32 40 02 00:00:00.404 WRITE DMA EXT
Error 560 occurred at disk power-on lifetime: 258 hours (10 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 28 00 28 f1 e8 Error: UNC 40 sectors at LBA = 0x08f12800 = 150022144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 e8 28 f1 e8 02 00:00:00.410 READ DMA
c8 00 40 e8 28 f1 e8 02 00:00:00.405 READ DMA
35 00 40 e8 0d 32 40 02 00:00:00.404 WRITE DMA EXT
35 00 40 68 0c 32 40 02 00:00:00.404 WRITE DMA EXT
35 00 40 28 6e 31 40 02 00:00:00.404 WRITE DMA EXT
Error 559 occurred at disk power-on lifetime: 258 hours (10 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 28 00 28 f1 e8 Error: UNC 40 sectors at LBA = 0x08f12800 = 150022144
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 e8 28 f1 e8 02 00:00:00.405 READ DMA
35 00 40 e8 0d 32 40 02 00:00:00.404 WRITE DMA EXT
35 00 40 68 0c 32 40 02 00:00:00.404 WRITE DMA EXT
35 00 40 28 6e 31 40 02 00:00:00.404 WRITE DMA EXT
ca 00 00 e8 78 05 e9 02 00:00:00.404 WRITE DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 259 124820848
# 2 Extended offline Aborted by host 90% 231 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Completed_read_failure [90% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.