Page 1 of 1
Importing ZFS Pool doesn't work (from FreeNAS 7)
Posted: 13 May 2013 21:36
by firefist235
Hi all,
i used FreeNAS 7 with ZFS (5 HDDs in Raid-Z1) so far. Because i want to upgrade my NAS i decided to change to NAS4Free. But i can't import my ZFS Pool...
I exported the ZFS Pool in FreeNAS, Installed NAS4Free (9.1.0.1.690) on the USB Drive (i made an Image of the FreeNAS installation, just for sure) and everytime I type
i get the following error message:
Code: Select all
cannot get GEOM tree: Unknown error: -1
zpool list says that there are no pools available.
I added all the neccessary drives through the Management Page (Chose ZFS as Filesystem)
i hope you can help me, i couldn't find any solution
Re: Importing ZFS Pool doesn't work (from FreeNAS 7)
Posted: 13 May 2013 22:10
by raulfg3
try zpool impot -f (force import), but I do not remember to see cannot get GEOM in this forum (for a zpool import).
Better if boot from old FreeNAs 7 and do zpool history and zpool info to know how you create first time your pool.
Re: Importing ZFS Pool doesn't work (from FreeNAS 7)
Posted: 13 May 2013 22:16
by firefist235
force doesnt make a difference
gimme a sec
Re: Importing ZFS Pool doesn't work (from FreeNAS 7)
Posted: 13 May 2013 22:25
by firefist235
zpool info is an unrecognized command
this is zpool history
Code: Select all
History for 'BFR':
2010-09-17.17:57:10 zpool create -m /mnt/BFR BFR raidz1 /dev/ad2 /dev/ad4 /dev/ad6 /dev/ad8 /dev/ad10
2010-09-18.15:24:58 zpool import -f -a
2010-09-19.01:30:09 zpool import -f -a
2010-09-19.01:42:23 zpool import -f -a
2010-09-21.15:47:46 zpool import -f -a
2010-09-21.18:43:22 zpool import -f -a
2010-09-21.18:54:56 zpool import -f -a
2010-09-23.22:10:29 zpool import -f -a
2010-09-25.09:41:13 zpool import -f -a
2010-09-25.12:27:14 zpool import -f -a
2010-10-04.15:13:23 zpool import -f -a
2010-10-04.15:26:51 zpool import -f -a
2010-10-04.21:37:57 zpool scrub BFR
2010-10-06.20:00:52 zpool import -f -a
2010-10-19.22:45:03 zpool import -f -a
2010-10-21.22:01:21 zpool import -f -a
2010-10-21.22:10:39 zpool import -f -a
2010-10-21.22:21:06 zpool import -f -a
2010-10-21.22:31:09 zpool import -f -a
2010-10-21.22:54:06 zpool import -f -a
2010-10-25.13:16:30 zpool import -f -a
2010-10-25.13:21:51 zpool import -f -a
2010-10-25.14:02:45 zpool import -f -a
2010-10-25.14:18:48 zpool import -f -a
2010-10-26.00:51:43 zpool import -f -a
2010-11-04.22:54:20 zpool scrub BFR
2010-11-15.15:28:06 zpool import -f -a
2010-12-22.21:45:45 zpool import -f -a
2010-12-22.23:08:53 zpool import -f -a
2011-01-06.01:54:40 zpool import -f -a
2011-01-08.01:48:50 zpool import -f -a
2011-01-11.17:40:32 zpool scrub BFR
2011-01-14.15:14:42 zpool import -f -a
2011-02-05.20:16:48 zpool import -f -a
2011-03-15.15:27:09 zpool import -f -a
2011-05-20.15:41:36 zpool import -f -a
2011-06-03.20:37:01 zpool import -f -a
2011-08-02.19:33:25 zpool import -f -a
2011-08-02.20:36:25 zpool import -f -a
2011-08-02.22:40:50 zpool scrub BFR
2011-09-20.01:24:13 zpool scrub BFR
2011-11-05.10:52:44 zpool import -f -a
2011-12-27.17:17:59 zpool import -f -a
2012-01-04.18:37:28 zpool import -f -a
2012-01-04.18:52:17 zpool scrub BFR
2012-02-11.09:31:00 zpool import -f -a
2012-02-11.09:39:19 zpool scrub BFR
2012-03-30.16:37:26 zpool import -f -a
2012-06-26.21:14:11 zpool import -f -a
2012-07-04.19:48:44 zpool import -f -a
2012-07-05.19:02:04 zpool import -f -a
2012-07-07.12:55:06 zpool import -f -a
2012-07-07.18:34:23 zpool import -f -a
2012-07-08.09:58:07 zpool import -f -a
2012-07-12.19:50:33 zpool import -f -a
2012-07-21.19:14:43 zpool import -f -a
2012-07-29.18:26:06 zpool import -f -a
2012-07-31.19:05:21 zpool import -f -a
2012-08-01.20:26:51 zpool import -f -a
2012-08-03.21:34:32 zpool import -f -a
2012-08-14.13:47:30 zpool import -f -a
2012-08-14.13:55:55 zpool scrub BFR
2012-08-20.19:13:55 zpool import -f -a
2012-09-25.18:20:54 zpool import -f -a
2012-09-25.20:12:19 zpool import -f -a
2012-10-10.19:35:07 zpool import -f -a
2012-10-10.21:53:53 zpool import -f -a
2013-02-04.21:03:19 zpool import -f -a
2013-03-10.17:17:47 zpool import -f -a
2013-04-01.15:27:31 zpool import -f -a
2013-05-09.18:55:41 zpool import -f -a
2013-05-13.19:59:37 zpool import -f -a
2013-05-13.20:03:39 zpool export BFR
2013-05-13.22:20:31 zpool import -f -a
Re: Importing ZFS Pool doesn't work (from FreeNAS 7)
Posted: 13 May 2013 23:23
by raulfg3
try one more time, this time use:
if still have errors, you need help from gurus of the forums.
Re: Importing ZFS Pool doesn't work (from FreeNAS 7)
Posted: 15 May 2013 14:18
by sleid
I fear the worst, if you chose (Choose as ZFS Filesystem)
you had to choose "Unformatted" to leave the data in place.
Re: Importing ZFS Pool doesn't work (from FreeNAS 7)
Posted: 15 May 2013 14:26
by raulfg3
sleid wrote:I fear the worst, if you chose (Choose as ZFS Filesystem)
you had to choose "Unformatted" to leave the data in place.
no, you can choose ZFS too , to have it untouched ( I mean it when select disk, not if you format disk)
Re: Importing ZFS Pool doesn't work (from FreeNAS 7)
Posted: 15 May 2013 20:10
by firefist235
i tried the command you suggested but i get the same error message.
When i set up the ZFS Pool on FreeNAS 7 there were 5 x 1,5TB HDDs installed. Now i have 8 x 3 TB drives (new drives) on a LSI MegaRaid SAS Controller (Flashed with IT Mode Firmware) and the 5 1,5 TB drives connected to the mainbaord as i did before.
I have the following idea, to get my data from the old pool to the new one:
1) Take out 2 3 TB HDDs
2) Boot Server with working pool on FreeNAS
3) Install those 2 Drives in my PC
4) Copy the files through the network (FreeNAS cant recognize the SAS Controller) on the two 3 TB Drives
5) After that, destroy the "old" pool, and make seperate disks out of it
6) Copy the files from the 3 TB drives on the 1,5 TB Drives.
7) When finished install the two 3 TB drives back into the Server and make a raid-z1 pool out of them
8) Copy the files from the 1,5 TB Drives onto the pool.
9) When finished open up a beer and destroy something
Re: Importing ZFS Pool doesn't work (from FreeNAS 7)
Posted: 25 May 2013 20:42
by firefist235
Hi all,
sadly i stuck at step 7: i put the 3TB Drives back into my NAS and wanted to create a raid-z1 pool out of them. When i create a pool, it only lasts until the next reboot. After a reboot the pool is lost, an cannot be reimported, i get this error again, if i try
Code: Select all
cannot get GEOM tree: Unknown error: -1
my Harddrive-Info-page looks a bit strange too:
Code: Select all
Gerät /dev/da0 - ATA Hitachi HDS5C303 AAB0
Festplatte: da0
Firmware Rev:
ATA revision: unknown/pre ATA-2
LBA 48: no
Geometry: 0 cyls, 0 heads, 0 spt
Capacity: 0MB
SMART Supported: no
Write Cache Supported: no
APM Supported: no
AAM Supported: no
Gerät /dev/da1 - ATA Hitachi HDS5C303 AAB0
Festplatte: da1
Firmware Rev:
ATA revision: unknown/pre ATA-2
LBA 48: no
Geometry: 0 cyls, 0 heads, 0 spt
Capacity: 0MB
SMART Supported: no
Write Cache Supported: no
APM Supported: no
AAM Supported: no
Gerät /dev/da2 - ATA Hitachi HDS5C303 AAB0
Festplatte: da2
Firmware Rev:
ATA revision: unknown/pre ATA-2
LBA 48: no
Geometry: 0 cyls, 0 heads, 0 spt
Capacity: 0MB
SMART Supported: no
Write Cache Supported: no
APM Supported: no
AAM Supported: no
Gerät /dev/da3 - ATA Hitachi HDS5C303 AAB0
Festplatte: da3
Firmware Rev:
ATA revision: unknown/pre ATA-2
LBA 48: no
Geometry: 0 cyls, 0 heads, 0 spt
Capacity: 0MB
SMART Supported: no
Write Cache Supported: no
APM Supported: no
AAM Supported: no
Gerät /dev/da4 - ATA Hitachi HDS5C303 AAB0
Festplatte: da4
Firmware Rev:
ATA revision: unknown/pre ATA-2
LBA 48: no
Geometry: 0 cyls, 0 heads, 0 spt
Capacity: 0MB
SMART Supported: no
Write Cache Supported: no
APM Supported: no
AAM Supported: no
Gerät /dev/da5 - ATA Hitachi HDS5C303 AAB0
Festplatte: da5
Firmware Rev:
ATA revision: unknown/pre ATA-2
LBA 48: no
Geometry: 0 cyls, 0 heads, 0 spt
Capacity: 0MB
SMART Supported: no
Write Cache Supported: no
APM Supported: no
AAM Supported: no
Gerät /dev/da6 - ATA Hitachi HDS5C303 AAB0
Festplatte: da6
Firmware Rev:
ATA revision: unknown/pre ATA-2
LBA 48: no
Geometry: 0 cyls, 0 heads, 0 spt
Capacity: 0MB
SMART Supported: no
Write Cache Supported: no
APM Supported: no
AAM Supported: no
Gerät /dev/da7 - ATA Hitachi HDS5C303 AAB0
Festplatte: da7
Firmware Rev:
ATA revision: unknown/pre ATA-2
LBA 48: no
Geometry: 0 cyls, 0 heads, 0 spt
Capacity: 0MB
SMART Supported: no
Write Cache Supported: no
APM Supported: no
AAM Supported: no
Gerät /dev/da8 - G & T USB Flash Drive 5.00
Festplatte: da8
Firmware Rev:
ATA revision: unknown/pre ATA-2
LBA 48: no
Geometry: 0 cyls, 0 heads, 0 spt
Capacity: 0MB
SMART Supported: no
Write Cache Supported: no
APM Supported: no
AAM Supported: no
i hope you can help me out...
Re: Importing ZFS Pool doesn't work (from FreeNAS 7)
Posted: 26 May 2013 18:26
by firefist235
in the configuration utility of the controller card, i can choose between "Disabled", "OS Enabled", "BIOS Enabled" and "OS & BIOS Enabled" for "Boot configuration" or something like that (i am currently not at the server)
does this make any difference?
Re: Importing ZFS Pool doesn't work (from FreeNAS 7)
Posted: 01 Jun 2013 18:24
by firefist235
i flashed a firmware wihtout an configuration interface. so all HDDs are passed through automatically.
the same here, after reboot of NAS4Free the pool is dead
Re: Importing ZFS Pool doesn't work (from FreeNAS 7)
Posted: 03 Jun 2013 17:34
by fsbruva
I think a larger issue is the fact that your disk info shows max capacity of 0 MB for every drive!!!!