This is the old XigmaNAS forum in read only mode, I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
tynolol
Starter
Posts: 36Joined: 13 May 2013 23:38
Status:
Offline
Post
by tynolol 18 Jun 2014 14:50
Hello everyone,
I created two RAIDZ2 called "Time_Machine" and "NAS RAIDZ2" and I would like to delete one of them called "NAS RAIDZ2" but I don't know how to delete it. When I go in menu Disk-->ZFS-->pool-->virtual device there is only one of the both which appear (called Time Machine), but the other one doesn't appear. Furthermore when I go in menu Disk-->ZFS-->configuration-->detected the both are listed.
What does it means? Is the RAIDZ2 already deleted or is it still present?
Thank you
b0ssman
Forum Moderator
Posts: 2438Joined: 14 Feb 2013 08:34Location: Munich, Germany
Status:
Offline
Post
by b0ssman 18 Jun 2014 15:15
give us some more information.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
tynolol
Starter
Posts: 36Joined: 13 May 2013 23:38
Status:
Offline
Post
by tynolol 18 Jun 2014 15:45
I have a full install (the last one).
I reinstall nas4free recently because of these problem without restore a backup config (I restarted from a clean system) :
viewtopic.php?f=65&t=6730&p=38615#p38615
I restarted system several times and to delete the pool I tryed to format the HDDs of these pool (but the pool was already not listed in pool menu, that's why I tryed to delete it)
b0ssman
Forum Moderator
Posts: 2438Joined: 14 Feb 2013 08:34Location: Munich, Germany
Status:
Offline
Post
by b0ssman 18 Jun 2014 15:58
zpool destroy NAS
from the command line
i would advise you to use the embedded install rather than the full.
on an embedded install you would not have had the problem.
see
http://wiki.nas4free.org/doku.php?id=faq:0073 Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
tynolol
Starter
Posts: 36Joined: 13 May 2013 23:38
Status:
Offline
Post
by tynolol 18 Jun 2014 16:08
I don't know some people advice to use full others to use embedded... I'm lost^^
Last edited by
tynolol on 18 Jun 2014 16:19, edited 1 time in total.
b0ssman
Forum Moderator
Posts: 2438Joined: 14 Feb 2013 08:34Location: Munich, Germany
Status:
Offline
Post
by b0ssman 18 Jun 2014 16:12
there is no question that you should use the embedded install.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
tynolol
Starter
Posts: 36Joined: 13 May 2013 23:38
Status:
Offline
Post
by tynolol 18 Jun 2014 16:33
so what should I reinstall my system??
b0ssman
Forum Moderator
Posts: 2438Joined: 14 Feb 2013 08:34Location: Munich, Germany
Status:
Offline
Post
by b0ssman 18 Jun 2014 16:48
save the config.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
kenZ71
Advanced User
Posts: 379Joined: 27 Jun 2012 20:18Location: Northeast, USA
Status:
Offline
Post
by kenZ71 19 Jun 2014 03:30
b0ssman wrote: save the config.
Yes, it is that easy. You can unplug your data drives while reinstalling as an added safety.
11.2-RELEASE-p3 | ZFS Mirror - 2 x 8TB WD Red | 28GB ECC Ram
