This is the old XigmaNAS forum in read only mode,
it will taken offline by the end of march 2021!


I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!

Identify Failing Disk in ZFS Pool?

Forum rules
• Set-Up Guide • FAQs • Forum Rules
Post Reply
molbert
Starter
Starter
Posts: 16
Joined: 21 Oct 2014 18:58
Status: Offline

Identify Failing Disk in ZFS Pool?

Post by molbert »

I'm getting failures of backups which use my NAS4Free ZFS pool as a backup medium. The messages from the backup software imply a disk fault of some kind.

I'm currently running scrub on the pool. But I'm wondering if there are other ways of detecting a bad or failing disk that's part of a ZFS pool.

FWIW, the drives in questions are Seagates. I've had a number of problems with similar drives in the last couple of years. So it wouldn't surprise me if one of drives is failing.
Top
User avatar
b0ssman
Forum Moderator
Forum Moderator
Posts: 2438
Joined: 14 Feb 2013 08:34
Location: Munich, Germany
Status: Offline

Re: Identify Failing Disk in ZFS Pool?

Post by b0ssman »

first post the smart values of your drives.

then setup email and smart monitoring

Disks|Management|S.M.A.R.T.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
Top
molbert
Starter
Starter
Posts: 16
Joined: 21 Oct 2014 18:58
Status: Offline

Re: Identify Failing Disk in ZFS Pool?

Post by molbert »

Here are the SMART values for one of the four drives. The other drives show similar results.

ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 102 099 006 Pre-fail Always - 3882552
3 Spin_Up_Time 0x0003 094 094 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 096 096 020 Old_age Always - 4346
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 069 060 030 Pre-fail Always - 4304884865
9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 3159
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 992
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 0 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 065 052 045 Old_age Always - 35 (Min/Max 22/42)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 43
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 5624
194 Temperature_Celsius 0x0022 035 048 000 Old_age Always - 35 (0 16 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 1597h+22m+16.760s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 107299943385
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 6621125620

If I'm reading this correctly, all of the drives are borderline (i.e., pre-fail).
Top
User avatar
crowi
Forum Moderator
Forum Moderator
Posts: 1176
Joined: 21 Feb 2013 16:18
Location: Munich, Germany
Status: Offline

Re: Identify Failing Disk in ZFS Pool?

Post by crowi »

If I'm reading this correctly, all of the drives are borderline (i.e., pre-fail).
How do you get to this assumption?
I don't see anything to worry about, but maybe I missed it. ;)

http://en.wikipedia.org/wiki/S.M.A.R.T.


Of course you should post the values of all drives...
NAS 1: Milchkuh: Asrock C2550D4I, Intel Avoton C2550 Quad-Core, 16GB DDR3 ECC, 5x3TB WD Red RaidZ1 +60 GB SSD for ZIL/L2ARC, APC-Back UPS 350 CS, NAS4Free 11.0.0.4.3460 embedded
NAS 2: Backup: HP N54L, 8 GB ECC RAM, 4x4 TB WD Red, RaidZ1, NAS4Free 11.0.0.4.3460 embedded
NAS 3: Office: HP N54L, 8 GB ECC RAM, 2x3 TB WD Red, ZFS Mirror, APC-Back UPS 350 CS NAS4Free 11.0.0.4.3460 embedded
Top
molbert
Starter
Starter
Posts: 16
Joined: 21 Oct 2014 18:58
Status: Offline

Re: Identify Failing Disk in ZFS Pool?

Post by molbert »

Perhaps I'm reading the results wrong. I thought all of the "pre-fail" entries in the "type" column meant the drives were borderline.
Top
molbert
Starter
Starter
Posts: 16
Joined: 21 Oct 2014 18:58
Status: Offline

Re: Identify Failing Disk in ZFS Pool?

Post by molbert »

Code: Select all

Here is the complete report.


Device /dev/ada0 - Seagate Barracuda 7200.14 (AF)
=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.14 (AF)
Device Model:     ST3000DM001-1CH166
Serial Number:    Z1F2YR57
LU WWN Device Id: 5 000c50 0507c9618
Firmware Version: CC26
User Capacity:    3,000,592,982,016 bytes [3.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Mon Feb 23 08:16:07 2015 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever
					been run.
Total time to complete Offline
data collection: 		(  592) seconds.
Offline data collection
capabilities: 			 (0x73) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 338) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x3085)	SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   102   099   006    Pre-fail  Always       -       3882552
  3 Spin_Up_Time            0x0003   094   094   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   096   096   020    Old_age   Always       -       4346
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   069   060   030    Pre-fail  Always       -       4304884865
  9 Power_On_Hours          0x0032   097   097   000    Old_age   Always       -       3159
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       992
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0 0 0
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   065   052   045    Old_age   Always       -       35 (Min/Max 22/42)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       43
193 Load_Cycle_Count        0x0032   098   098   000    Old_age   Always       -       5624
194 Temperature_Celsius     0x0022   035   048   000    Old_age   Always       -       35 (0 16 0 0 0)
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       1597h+22m+16.760s
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       107299943385
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       6621125620

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%      3158         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Device /dev/ada1 - Seagate Barracuda 7200.14 (AF)
=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.14 (AF)
Device Model:     ST3000DM001-1CH166
Serial Number:    Z1F2YFSB
LU WWN Device Id: 5 000c50 05081075c
Firmware Version: CC26
User Capacity:    3,000,592,982,016 bytes [3.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Mon Feb 23 08:16:08 2015 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever
					been run.
Total time to complete Offline
data collection: 		(  584) seconds.
Offline data collection
capabilities: 			 (0x73) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 353) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x3085)	SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   114   099   006    Pre-fail  Always       -       64545808
  3 Spin_Up_Time            0x0003   093   093   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   096   096   020    Old_age   Always       -       4331
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   069   060   030    Pre-fail  Always       -       9895104
  9 Power_On_Hours          0x0032   097   097   000    Old_age   Always       -       3161
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       994
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0 0 0
189 High_Fly_Writes         0x003a   094   094   000    Old_age   Always       -       6
190 Airflow_Temperature_Cel 0x0022   064   054   045    Old_age   Always       -       36 (Min/Max 22/40)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       29
193 Load_Cycle_Count        0x0032   098   098   000    Old_age   Always       -       5578
194 Temperature_Celsius     0x0022   036   046   000    Old_age   Always       -       36 (0 15 0 0 0)
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       1595h+24m+08.316s
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       107286019169
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       6616512724

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%      3161         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Device /dev/ada2 - Seagate Barracuda 7200.14 (AF)
=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.14 (AF)
Device Model:     ST3000DM001-1CH166
Serial Number:    W1F2SLPN
LU WWN Device Id: 5 000c50 0606d2492
Firmware Version: CC26
User Capacity:    3,000,592,982,016 bytes [3.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Mon Feb 23 08:16:08 2015 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever
					been run.
Total time to complete Offline
data collection: 		(  584) seconds.
Offline data collection
capabilities: 			 (0x73) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 332) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x3085)	SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   109   099   006    Pre-fail  Always       -       22436720
  3 Spin_Up_Time            0x0003   094   094   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   096   096   020    Old_age   Always       -       4337
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   069   060   030    Pre-fail  Always       -       4304747604
  9 Power_On_Hours          0x0032   097   097   000    Old_age   Always       -       3161
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       992
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0 0 0
189 High_Fly_Writes         0x003a   091   091   000    Old_age   Always       -       9
190 Airflow_Temperature_Cel 0x0022   068   052   045    Old_age   Always       -       32 (Min/Max 22/38)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       26
193 Load_Cycle_Count        0x0032   098   098   000    Old_age   Always       -       5599
194 Temperature_Celsius     0x0022   032   048   000    Old_age   Always       -       32 (0 16 0 0 0)
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       1598h+30m+13.422s
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       107299077705
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       6621184609

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%      3161         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Device /dev/ada3 - Seagate Barracuda 7200.14 (AF)
=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.14 (AF)
Device Model:     ST3000DM001-1CH166
Serial Number:    Z1F2YENB
LU WWN Device Id: 5 000c50 050812206
Firmware Version: CC26
User Capacity:    3,000,592,982,016 bytes [3.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Mon Feb 23 08:16:08 2015 PST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever
					been run.
Total time to complete Offline
data collection: 		(  584) seconds.
Offline data collection
capabilities: 			 (0x73) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 338) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x3085)	SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   117   099   006    Pre-fail  Always       -       160835752
  3 Spin_Up_Time            0x0003   093   093   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   096   096   020    Old_age   Always       -       4331
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   069   060   030    Pre-fail  Always       -       9929705
  9 Power_On_Hours          0x0032   097   097   000    Old_age   Always       -       3161
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       994
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -       0
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0 0 0
189 High_Fly_Writes         0x003a   095   095   000    Old_age   Always       -       5
190 Airflow_Temperature_Cel 0x0022   069   053   045    Old_age   Always       -       31 (Min/Max 22/36)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       28
193 Load_Cycle_Count        0x0032   098   098   000    Old_age   Always       -       5584
194 Temperature_Celsius     0x0022   031   047   000    Old_age   Always       -       31 (0 16 0 0 0)
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       1595h+35m+29.262s
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       107298786985
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       6618375406

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%      3161         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Top
molbert
Starter
Starter
Posts: 16
Joined: 21 Oct 2014 18:58
Status: Offline

Re: Identify Failing Disk in ZFS Pool?

Post by molbert »

Okay, did some more research and see why you say there's nothing to worry about. The "type" column simply indicates how important that particular attribute is to determining the health of the drive. "Pre-fail" doesn't mean the current value means the drive is about to fail. It means that if the value drops below the threshold the drive should be considered about to fail (and that the SMART test should result in FAILED rather than PASSED).

So I wonder why I was getting what appeared to be access problems on the drive array...
Top
User avatar
b0ssman
Forum Moderator
Forum Moderator
Posts: 2438
Joined: 14 Feb 2013 08:34
Location: Munich, Germany
Status: Offline

Re: Identify Failing Disk in ZFS Pool?

Post by b0ssman »

the smart values look fine.

some drives have high fly values bigger than 0 that could indicate problems with vibration in the case but nothing serious.

please post the output of zpool status.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
Top
molbert
Starter
Starter
Posts: 16
Joined: 21 Oct 2014 18:58
Status: Offline

Re: Identify Failing Disk in ZFS Pool?

Post by molbert »

Thanx. Here's the zpool status report. FYI, I did a scrub on the pool (there's only one) yesterday and it reported no errors and had nothing to repair.

Code: Select all

 pool: Pool0
 state: ONLINE
status: The pool is formatted using a legacy on-disk format.  The pool can
	still be used, but some features are unavailable.
action: Upgrade the pool using 'zpool upgrade'.  Once this is done, the
	pool will no longer be accessible on software that does not support feature
	flags.
  scan: scrub repaired 0 in 4h42m with 0 errors on Sun Feb 22 23:20:27 2015
config:

	NAME          STATE     READ WRITE CKSUM
	Pool0         ONLINE       0     0     0
	  mirror-0    ONLINE       0     0     0
	    ada0.nop  ONLINE       0     0     0
	    ada1.nop  ONLINE       0     0     0
	  mirror-1    ONLINE       0     0     0
	    ada2.nop  ONLINE       0     0     0
	    ada3.nop  ONLINE       0     0     0

errors: No known data errors
Top
User avatar
b0ssman
Forum Moderator
Forum Moderator
Posts: 2438
Joined: 14 Feb 2013 08:34
Location: Munich, Germany
Status: Offline

Re: Identify Failing Disk in ZFS Pool?

Post by b0ssman »

so everything looks fine.
the fault might be in the backup tool.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
Top
molbert
Starter
Starter
Posts: 16
Joined: 21 Oct 2014 18:58
Status: Offline

Re: Identify Failing Disk in ZFS Pool?

Post by molbert »

That's looking more likely. Thanx for your help!
Top
Post Reply

Return to “ZFS (only!)”