Hello, I asked this beforeviewtopic.php?f=57&t=8994, but NAS4Free links are showing a lot of 404 errors.
I install NAS4Free from USB1. The install documentation http://www.zoonsweb.nl/wiki/doku.php?id ... n_overview says to then do an embedded install.
I try embedding to USB 1 but that doesn't boot NAS4Free after a restart.
I try embedding to USB 2 but that doesn't boot NAS4Free after a restart.
So, do I add a 2nd USB to install NAS4Free onto?
It seems I can just run NAS4Free from the original USB 1. Why and what is the embed bit for and how can I make this embed thingy work?
This is the old XigmaNAS forum in read only mode,
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
How to embed install to USB?
-
eiger3970
- NewUser
- Posts: 7
- Joined: 01 Jun 2015 10:20
- Status: Offline
-
crowi
- Forum Moderator
- Posts: 1176
- Joined: 21 Feb 2013 16:18
- Location: Munich, Germany
- Status: Offline
Re: How to embed install to USB?
you need 2 USB sticks to install the embedded.
One to install from it (containing the LiveUSB image and one to install to it, which will contain the the system after installation.
One to install from it (containing the LiveUSB image and one to install to it, which will contain the the system after installation.
NAS 1: Milchkuh: Asrock C2550D4I, Intel Avoton C2550 Quad-Core, 16GB DDR3 ECC, 5x3TB WD Red RaidZ1 +60 GB SSD for ZIL/L2ARC, APC-Back UPS 350 CS, NAS4Free 11.0.0.4.3460 embedded
NAS 2: Backup: HP N54L, 8 GB ECC RAM, 4x4 TB WD Red, RaidZ1, NAS4Free 11.0.0.4.3460 embedded
NAS 3: Office: HP N54L, 8 GB ECC RAM, 2x3 TB WD Red, ZFS Mirror, APC-Back UPS 350 CS NAS4Free 11.0.0.4.3460 embedded
NAS 2: Backup: HP N54L, 8 GB ECC RAM, 4x4 TB WD Red, RaidZ1, NAS4Free 11.0.0.4.3460 embedded
NAS 3: Office: HP N54L, 8 GB ECC RAM, 2x3 TB WD Red, ZFS Mirror, APC-Back UPS 350 CS NAS4Free 11.0.0.4.3460 embedded
-
Cramin
- Starter
- Posts: 24
- Joined: 14 Jul 2014 07:57
- Location: Myszkow (Poland)
- Contact:
- Status: Offline
Re: How to embed install to USB?
And after restart change in BIOS boot order to boot from USB2.
Lian Li NAS - 12.1.0.4 - Ingva P2C E5700 + 4GB DDR2 + 2x (Raid1 2x500GB WD) + Raid1 2x500GB Samsung - Home
HP ML110G2 - 12.1.0.4 - Ingva P4 641 + 4GB DDR2 ECC + Raid1 2x80Gb WD + Raid1 2x250Gb Seagate - Work
HP ML110G2 - 12.1.0.4 - Ingva P4 641 + 4GB DDR2 ECC + Raid1 2x80Gb WD + Raid1 2x250Gb Seagate - Work
-
armandh
- Advanced User
- Posts: 398
- Joined: 23 Jun 2012 04:15
- Location: St Louis County Missouri USA
- Status: Offline
Re: How to embed install to USB?
easier to remove the live source USB stick and move the USB stick with the embedded install to the vacated spot
4 thread 3300 Mhz Intel i3, 1 TB ZFS mirror, available RAM 7.823 Gb, 64 bit NAS4Free 9.1.0.1 rev 573 [88 watts, 48 Mbps]
2 thread 1600 Mhz atom/ion, 1 TB ZFS mirror, available RAM 3.083 Gb, 64 bit NAS4Free-9.1.0.1 rev 573 [27 watts, 35 Mbps]
2 thread 3900 Mhz AMD A6-6400K, 2 TB ZFS Mirror, available RAM 7.557 Gb, 64 bit Nas4Free 9.3.0.2.1771 [89 watts, 68 Mbps]
2 thread 1600 Mhz atom/ion, 1 TB ZFS mirror, available RAM 3.083 Gb, 64 bit NAS4Free-9.1.0.1 rev 573 [27 watts, 35 Mbps]
2 thread 3900 Mhz AMD A6-6400K, 2 TB ZFS Mirror, available RAM 7.557 Gb, 64 bit Nas4Free 9.3.0.2.1771 [89 watts, 68 Mbps]