690's Report Gen:
Code: Select all
NAS4Free 10.2.0.2 (revision 2235) x64-embedded
DELL B8K Intel(R) Xeon(R) CPU E5320 @ 1.86GHz 8192MiB RAM
Intel 63XXESB USB 2.0 controller BCM5752 1000BASE-T media interface
Intel 631XESB/632XESB/3100 USB controller USB-1 Intel
631XESB/632XESB/3100 USB controller USB-2 Intel 631XESB/632XESB/3100
USB controller USB-3 Intel 63XXESB2 UDMA100 controller Intel
631XESB/632XESB/3100 USB controller USB-4 bus=4 hubaddr=1 port=7
devaddr=2 interface=0 ugen=ugen4.2
Since the computers are directly connected, I've set the NIC's up with static IP's as follows:
HP Z800:
Onboard 1GbE NIC:
IP: 192.168.1.20
Subnet mask: 255.255.255.0
Default gateway: 192.168.1.250
Mellanox 10GbE NIC:
IP: 192.168.1.30
Subnet mask: 255.255.255.0
Default Gateway: 192.168.1.251
Precision 690 - NAS4Free:
Onboard LAN (built-in 1GbE NIC):
IP: 192.168.1.250/24 (the default, of course)
Gateway: 192.168.1.20
Mellanox 10GbE NIC:
IP: 192.168.1.251/24
Gateway: 192.168.1.30
I can access the NAS4Free GUI without issue at 192.168.1.250 from the Z800, but if I set my CFIS share to "OPT Only," the mapped network drive no longer can be accessed from Windows. If I restore "All Interfaces," the shared drive can be pulled back up in the Windows box.
That said, I've run AngryIPScanner (on Windows) during every one of my tests, and 192.168.1.251 is always dead, and it won't ping from the command prompt either. On the NAS4Free box, I can ping 192.168.1.20 with success, but not 192.168.1.30.
This is my dmesg:
Code: Select all
edit690: ~# dmesg
Copyright (c) 1992-2015 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.2-RELEASE-p8 #0 r292129M: Fri Dec 11 23:47:42 CET 2015
root@dev.nas4free.org:/usr/obj/nas4free/usr/src/sys/NAS4FREE-amd64 amd64
FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
CPU: Intel(R) Xeon(R) CPU E5320 @ 1.86GHz (1861.95-MHz K8-class CPU)
Origin="GenuineIntel" Id=0x6f7 Family=0x6 Model=0xf Stepping=7
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x4e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,DCA>
AMD Features=0x20100800<SYSCALL,NX,LM>
AMD Features2=0x1<LAHF>
VT-x: HLT,PAUSE
TSC: P-state invariant, performance statistics
real memory = 8589934592 (8192 MB)
avail memory = 8244269056 (7862 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <DELL B8K >
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
FreeBSD/SMP: 2 package(s) x 4 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
cpu4 (AP): APIC ID: 4
cpu5 (AP): APIC ID: 5
cpu6 (AP): APIC ID: 6
cpu7 (AP): APIC ID: 7
WARNING: VIMAGE (virtualized network stack) is a highly experimental feature.
ACPI BIOS Warning (bug): Incorrect checksum in table [TCPA] - 0x00, should be 0x88 (20150515/tbprint-228)
ioapic0: Changing APIC ID to 8
ioapic1: Changing APIC ID to 9
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 24-47 on motherboard
kbd1 at kbdmux0
random: <Software, Yarrow> initialized
cryptosoft0: <software crypto> on motherboard
acpi0: <DELL B8K > on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
cpu4: <ACPI CPU> on acpi0
cpu5: <ACPI CPU> on acpi0
cpu6: <ACPI CPU> on acpi0
cpu7: <ACPI CPU> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x7f irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x5f irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 350
Event timer "HPET1" frequency 14318180 Hz quality 340
Event timer "HPET2" frequency 14318180 Hz quality 340
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pcib0: Length mismatch for 3 range: e000001 vs e000000
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 0.0 on pci1
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 0.0 on pci2
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci2
pci4: <ACPI PCI bus> on pcib4
mps0: <Avago Technologies (LSI) SAS2008> port 0xcc00-0xccff mem 0xfcab0000-0xfcabffff,0xfcac0000-0xfcafffff irq 17 at device 0.0 on pci4
mps0: Firmware: 20.00.04.00, Driver: 20.00.00.00-fbsd
mps0: IOCCapabilities: 1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc>
pcib5: <ACPI PCI-PCI bridge> at device 0.3 on pci1
pci5: <ACPI PCI bus> on pcib5
pcib6: <ACPI PCI-PCI bridge> at device 3.0 on pci0
pci6: <ACPI PCI bus> on pcib6
pci6: <network, ethernet> at device 0.0 (no driver attached)
pcib7: <ACPI PCI-PCI bridge> at device 4.0 on pci0
pci7: <ACPI PCI bus> on pcib7
vgapci0: <VGA-compatible display> port 0xdc00-0xdcff mem 0xf0000000-0xf7ffffff,0xfcde0000-0xfcdeffff irq 16 at device 0.0 on pci7
vgapci0: Boot video device
vgapci1: <VGA-compatible display> mem 0xfcdf0000-0xfcdfffff at device 0.1 on pci7
pcib8: <ACPI PCI-PCI bridge> at device 5.0 on pci0
pci8: <ACPI PCI bus> on pcib8
pcib9: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci9: <ACPI PCI bus> on pcib9
pcib10: <ACPI PCI-PCI bridge> at device 7.0 on pci0
pci10: <ACPI PCI bus> on pcib10
hdac0: <Intel 631x/632xESB HDA Controller> mem 0xfcffc000-0xfcffffff irq 16 at device 27.0 on pci0
pcib11: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci11: <ACPI PCI bus> on pcib11
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x006002> mem 0xfc6f0000-0xfc6fffff irq 16 at device 0.0 on pci11
bge0: CHIP ID 0x00006002; ASIC REV 0x06; CHIP REV 0x60; PCI-E
miibus0: <MII bus> on bge0
brgphy0: <BCM5752 1000BASE-T media interface> PHY 1 on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge0: Ethernet address: 00:1a:a0:c0:8c:2b
uhci0: <Intel 631XESB/632XESB/3100 USB controller USB-1> port 0xff80-0xff9f irq 21 at device 29.0 on pci0
usbus0 on uhci0
uhci1: <Intel 631XESB/632XESB/3100 USB controller USB-2> port 0xff60-0xff7f irq 22 at device 29.1 on pci0
usbus1 on uhci1
uhci2: <Intel 631XESB/632XESB/3100 USB controller USB-3> port 0xff40-0xff5f irq 18 at device 29.2 on pci0
usbus2 on uhci2
uhci3: <Intel 631XESB/632XESB/3100 USB controller USB-4> port 0xff20-0xff3f irq 23 at device 29.3 on pci0
usbus3 on uhci3
ehci0: <Intel 63XXESB USB 2.0 controller> mem 0xff980800-0xff980bff irq 21 at device 29.7 on pci0
usbus4: EHCI version 1.0
usbus4 on ehci0
pcib12: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci12: <ACPI PCI bus> on pcib12
pci12: <serial bus, FireWire> at device 10.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel 63XXESB2 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf irq 16 at device 31.1 on pci0
ata0: <ATA channel> at channel 0 on atapci0
ahci0: <Intel ESB2 AHCI SATA controller> port 0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfec0-0xfedf mem 0xff970000-0xff9703ff irq 20 at device 31.2 on pci0
ahci0: AHCI v1.10 with 6 3Gbps ports, Port Multiplier not supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich2: <AHCI channel> at channel 2 on ahci0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xccfff,0xcd000-0xce7ff,0xce800-0xd07ff,0xd0800-0xd2fff,0xd3000-0xd3fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
coretemp2: <CPU On-Die Thermal Sensors> on cpu2
est2: <Enhanced SpeedStep Frequency Control> on cpu2
p4tcc2: <CPU Frequency Thermal Control> on cpu2
coretemp3: <CPU On-Die Thermal Sensors> on cpu3
est3: <Enhanced SpeedStep Frequency Control> on cpu3
p4tcc3: <CPU Frequency Thermal Control> on cpu3
coretemp4: <CPU On-Die Thermal Sensors> on cpu4
est4: <Enhanced SpeedStep Frequency Control> on cpu4
p4tcc4: <CPU Frequency Thermal Control> on cpu4
coretemp5: <CPU On-Die Thermal Sensors> on cpu5
est5: <Enhanced SpeedStep Frequency Control> on cpu5
p4tcc5: <CPU Frequency Thermal Control> on cpu5
coretemp6: <CPU On-Die Thermal Sensors> on cpu6
est6: <Enhanced SpeedStep Frequency Control> on cpu6
p4tcc6: <CPU Frequency Thermal Control> on cpu6
coretemp7: <CPU On-Die Thermal Sensors> on cpu7
est7: <Enhanced SpeedStep Frequency Control> on cpu7
p4tcc7: <CPU Frequency Thermal Control> on cpu7
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
Timecounters tick every 1.000 msec
iSCSI boot driver version 0.2.13
xmd version 0.5 by NAS4Free Project
xmd: default blocklen 32KB, compression LZ4/LZ4HC, level 6
xmd0: Loaded preload cloop image </mfsroot.uzip> 21699072 bytes at 0xffffffff8211ac60 (128MB disk w/LZ4)
random: unblocking device.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
ugen1.1: <Intel> at usbus1
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen0.1: <Intel> at usbus0
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen4.1: <Intel> at usbus4
uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen2.1: <Intel> at usbus2
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
hdacc0: <Sigmatel STAC9220 HDA CODEC> at cad 0 on hdac0
hdaa0: <Sigmatel STAC9220 Audio Function Group> at nid 1 on hdacc0
pcm0: <Sigmatel STAC9220 (Analog 2.0+HP/2.0)> at nid 14,13 and 16,15 on hdaa0
uhub1: 2 ports with 2 removable, self powered
uhub0: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
mps0: SAS Address for SATA device = 816f9e3285d2d4c1
mps0: SAS Address from SATA device = 816f9e3285d2d4c1
mps0: SAS Address for SATA device = 4868483ee1e4ae8f
mps0: SAS Address from SATA device = 4868483ee1e4ae8f
mps0: SAS Address for SATA device = 816f9e339cdcd3c1
mps0: SAS Address from SATA device = 816f9e339cdcd3c1
mps0: SAS Address for SATA device = 4868483ee1e4d171
mps0: SAS Address from SATA device = 4868483ee1e4d171
mps0: SAS Address for SATA device = 816f9e319de7f7c1
mps0: SAS Address from SATA device = 816f9e319de7f7c1
mps0: SAS Address for SATA device = 816f9e3296defac1
mps0: SAS Address from SATA device = 816f9e3296defac1
uhub2: 8 ports with 8 removable, self powered
ugen4.2: <SanDisk> at usbus4
umass0: <SanDisk Cruzer Fit, class 0/0, rev 2.10/1.00, addr 2> on usbus4
umass0: SCSI over Bulk-Only; quirks = 0x8100
umass0:5:0:-1: Attached to scbus5
da4 at mps0 bus 0 scbus0 target 8 lun 0
da6 at umass-sim0 bus 0 scbus5 target 0 lun 0
da4: <ATA WDC WD60EFRX-68M 0A82> Fixed Direct Access SPC-4 SCSI device
da4: Serial Number WD-WX91D6535TT6
da4: 600.000MB/s transfers
da4: Command Queueing enabled
da4: 5723166MB (11721045168 512 byte sectors: 255H 63S/T 729601C)
da4: quirks=0x8<4K>
da1 at mps0 bus 0 scbus0 target 2 lun 0
da1: <ATA Hitachi HUA72202 A3EA> Fixed Direct Access SPC-4 SCSI device
da6: <SanDisk Cruzer Fit 1.00> Removable Direct Access SPC-4 SCSI device
da6: Serial Number 4C531000611108113342
da6: 40.000MB/s transfers
da6: 7632MB (15630336 512 byte sectors: 255H 63S/T 972C)
da6: quirks=0x2<NO_6_BYTE>
da5 at mps0 bus 0 scbus0 target 9 lun 0
da5: <ATA WDC WD60EFRX-68M 0A82> Fixed Direct Access SPC-4 SCSI device
da5: Serial Number WD-WX91D6535T1T
da5: 600.000MB/s transfers
da5: Command Queueing enabled
da5: 5723166MB (11721045168 512 byte sectors: 255H 63S/T 729601C)
da5: quirks=0x8<4K>
da0 at mps0 bus 0 scbus0 target 1 lun 0
da0: <ATA Hitachi HUA72202 A3EA> Fixed Direct Access SPC-4 SCSI device
da1: Serial Number JK11A1YAJ5KK0V
da1: 300.000MB/s transfers
da1: Command Queueing enabled
da1: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da3 at mps0 bus 0 scbus0 target 4 lun 0
da3: <ATA Hitachi HUA72202 A3EA> Fixed Direct Access SPC-4 SCSI device
da3: Serial Number JK11A1YAJ4EMWV
da3: 300.000MB/s transfers
da3: Command Queueing enabled
da3: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da0: Serial Number JK11A1YAJ44A1V
da0: 300.000MB/s transfers
da0: Command Queueing enabled
da0: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
da2 at mps0 bus 0 scbus0 target 3 lun 0
da2: <ATA Hitachi HUA72202 A3EA> Fixed Direct Access SPC-4 SCSI device
da2: Serial Number JK11A1YAJ3LVTV
da2: 300.000MB/s transfers
da2: Command Queueing enabled
da2: 1907729MB (3907029168 512 byte sectors: 255H 63S/T 243201C)
ada0 at ahcich0 bus 0 scbus2 target 0 lun 0
ada0: <Hitachi HUA722020ALA330 JKAOA3EA> ATA8-ACS SATA 2.x device
ada0: Serial Number JK11A1YAJ5RN5V
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada1 at ahcich1 bus 0 scbus3 target 0 lun 0
ada1: <Hitachi HUA722020ALA330 JKAOA3EA> ATA8-ACS SATA 2.x device
ada1: Serial Number JK11A1YAJ5LH0V
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
mlx4_core0: <mlx4_core> mem 0xfc700000-0xfc7fffff,0xf8000000-0xf87fffff irq 16 at device 0.0 on pci6
mlx4_core: Mellanox ConnectX core driver v2.1 (Dec 11 2015)
mlx4_en: Mellanox ConnectX HCA Ethernet driver v2.1 (Dec 11 2015)
mlxen0: Ethernet address: 00:02:c9:53:d4:e8
mlx4_en: mlx4_core0: Port 1: Using 8 TX rings
mlx4_en: mlx4_core0: Port 1: Using 8 RX rings
mlx4_en: mlxen0: Using 8 TX rings
mlx4_en: mlxen0: Using 8 RX rings
mlx4_en: mlxen0: Initializing port
SMP: AP CPU #5 Launched!
SMP: AP CPU #4 Launched!
SMP: AP CPU #7 Launched!
SMP: AP CPU #6 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
Timecounter "TSC" frequency 1861952022 Hz quality 1000
Trying to mount root from ufs:/dev/xmd0 []...
mlx4_en: mlxen0: Link Down
Code: Select all
edit690: ~# ifconfig
bge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether 00:1a:a0:c0:8c:2b
inet 192.168.1.250 netmask 0xffffff00 broadcast 192.168.1.255
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet autoselect (1000baseT <full-duplex>)
status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
inet 127.0.0.1 netmask 0xff000000
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
mlxen0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=d07bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,TSO6,LRO,VLAN_HWFILTER,VLAN_HWTSO,LINKSTATE>
ether 00:02:c9:53:d4:e8
inet 192.168.1.251 netmask 0xffffff00 broadcast 192.168.1.255
inet6 fe80::202:c9ff:fe53:d4e8%mlxen0 prefixlen 64 scopeid 0x3
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
media: Ethernet autoselect (10Gbase-SR <full-duplex,rxpause,txpause>)
status: active
However, Windows does report that the cards must be sharing very limited packets of data, as the connection for the 10GbE card on Windows reports both received packets, but very few (8,664 sent to 2,048 received).
What am I missing? I get the feeling that I'm missing something very simple here.
-Kurt
