Hi,
I just downloaded the alcatraz version of The Brig and installed it, but when I add jails the IP is empty and if I run jls on the command line I get an empty list.
On the GUI the jails are showing as started (but no IP)
Any ideas?? anyone got it working with 10.2.0.2 Prester?
Storms
This is the old XigmaNAS forum in read only mode,
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
The BRIG with 10.2.0.2 - Prester (revision 2223) No Ip's showing for jails
-
Storms
- NewUser
- Posts: 4
- Joined: 06 Nov 2014 21:18
- Location: Bradford, UK
- Status: Offline
The BRIG with 10.2.0.2 - Prester (revision 2223) No Ip's showing for jails
Motherboard: Gigabyte GA-78LMT-USB3
CPU: AMD FX-6100 Six-Core Processor
Storage: 6 x 2TB Western Digital 3.5 hard drives
RAM: 32GB DDR3
Boot device: KINGSTON 120GB SSD (connected via PCI Card)
Redundancy: raidz2
Installation type: RootOnZfs
CPU: AMD FX-6100 Six-Core Processor
Storage: 6 x 2TB Western Digital 3.5 hard drives
RAM: 32GB DDR3
Boot device: KINGSTON 120GB SSD (connected via PCI Card)
Redundancy: raidz2
Installation type: RootOnZfs
-
spy0r
- Advanced User
- Posts: 160
- Joined: 18 Jun 2015 12:24
- Location: Munich, Germany
- Status: Offline
Re: The BRIG with 10.2.0.2 - Prester (revision 2223) No Ip's showing for jails
Please read this one: viewtopic.php?f=79&t=9319&p=59043&hilit ... ing#p59043
NAS4Free 11.0.0.4 x64-embedded - Lian Li Q25b - AsRock Rack C2550D4I - 4x8Gb ECC Ram - 128Gb SSD Swap/Log/Extensions - RaidZ1: 3x3Tb Western Digital Red (WD30EFRX) - Backup: 1x8Tb Seagate Archive (ST8000AS0002) - APC Back UPS PRO (550VA)
-
Storms
- NewUser
- Posts: 4
- Joined: 06 Nov 2014 21:18
- Location: Bradford, UK
- Status: Offline
Re: The BRIG with 10.2.0.2 - Prester (revision 2223) No Ip's showing for jails
The problem was that I wasn't setting up networking correctly when creating the jail.
In the 'Networking' section I chose 're0' and 192.168.1.200/24 then it worked
In the 'Networking' section I chose 're0' and 192.168.1.200/24 then it worked
Motherboard: Gigabyte GA-78LMT-USB3
CPU: AMD FX-6100 Six-Core Processor
Storage: 6 x 2TB Western Digital 3.5 hard drives
RAM: 32GB DDR3
Boot device: KINGSTON 120GB SSD (connected via PCI Card)
Redundancy: raidz2
Installation type: RootOnZfs
CPU: AMD FX-6100 Six-Core Processor
Storage: 6 x 2TB Western Digital 3.5 hard drives
RAM: 32GB DDR3
Boot device: KINGSTON 120GB SSD (connected via PCI Card)
Redundancy: raidz2
Installation type: RootOnZfs