after upgrade : The device(s) in config are different to actual device(s)

[jmw]

Hi,

I just upgraded from 9.1 to 10.2.0.2 2268 by installing v10.2 on a new usb key, imported my config. Everything seems fine except that under 'Disks|Management|HDD management' I have the following message : The device(s) in config are different to actual device(s). Please remove the device(s) and re-add it or use 'Clear config and Import disks'.

I attache also a screen capture. But ZFS pool seems OK except that model and temperature are missing compared to the screen shot I made with version 9.1. The zfs pool is 1/3 full.

What should I do so that my disks are recognizzed.
Thanks for your help

[b0ssman]

press 'Clear config and Import disks'

[jmw]

thanks for your help

[RSS]

I have the same problem, and tracked this back from not being able to see video files through the Philips player I use, I'd selected clear config and import disks only for the disk size to come back wrong.

ada0 1718299MB D-D-C4C4ZEZEF4F4 ata2 nVidia nForce MCP51 SATA300 controller Always On Unknown or unformatted CHANGED (Device Serial : 'D-D-C4C4ZEZEF4F4' to 'WD-WCC4E4ZE16F4')

The disk is a 4TB (has been for a while now so since upgrading) and the error message is still there
The device(s) in config are different to actual device(s). Please remove the device(s) and re-add it or use 'Clear config and Import disks'.

So did the clear & import again, and this time it is correct.
ada0 WDC WD40EFRX-68WT0N0 3815448MB WD-WCC4E4ZE16F4 ata2 nVidia nForce MCP51 SATA300 controller Always On UFS ONLINE

Rebooted and everything up and running OK, but I've had this problem a few times now. I thought it might be an issue with the USB I boot from so bought a new 4GB Sandisk, loaded through a clean boot and restored the saved config (Win32 Diskmanager makes the USB readonly BTW so you can't reload a saved config) only to have the same problem the very next day.

What causes the problem? more importantly what do I need to do to fix this happening again, I've looked in the log and no error messages

The SMART data reported a checksum error but then passed, with an error about the USB bridge that I've not seen before, is this the root of the problem? if so it might have been with the other USB as well but they appear to behave in the same way.

Warning! SMART Attribute Data Structure error: invalid SMART checksum.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x01) Offline data collection activity
is in a Reserved state.
Auto Offline Data Collection: Disabled.
Total time to complete Offline
data collection: ( 3) seconds.
Offline data collection
capabilities: (0x00) Offline data collection not supported.
SMART capabilities: (0xff02) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x05) Error logging supported.
General Purpose Logging supported.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 176 172 021 Pre-fail Always - 8166
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 105
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 393
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 104
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 15
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 118
194 Temperature_Celsius 0x0022 114 109 000 Old_age Always - 38
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 000 000 000 Old_age Offline - 0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

Selective Self-tests/Logging not supported
Device /dev/da0 - SanDisk Cruzer Blade 2.01
/dev/da0: Unknown USB bridge [0x0781:0x5567 (0x201)]
Please specify device type with the -d option.

Use smartctl -h to get a usage summary
ID ATTRIBUTE NAME RAW VALUE DESCRIPTION
no data
/dev/da0: Unknown USB bridge [0x0781:0x5567 (0x201)]
Please specify device type with the -d option.

Use smartctl -h to get a usage summary