NAS4Free 10.2.0.2.2545 released (FreeBSD 10.2-RELEASE-P14)

[zoon01]

The NAS4Free Team is pleased to announce the release of version 10.2.0.2.2545

http://sourceforge.net/projects/nas4fre ... .0.2.2545/

Everyone can upgrade from NAS4Free version 9.3.0.2.1310 or Higher.

README & CHANGELOG

NAS4Free Upgrade from below 9.3.0.2.1310 is NOT possible!!!
=====================================================
Upgrading NAS4Free "Embedded" or "Full" from any version below 9.3.0.2.1310 by webgui or from
LiveCD/USB is problematic, due a new size of boot partition & partition layout.
Please download and save your NAS4Free config to a safe place and backup all files from second
partition if you use boot disk as data disk.
INSTALL FROM SCRATCH IS THE ONLY WAY!
After installation you can restore your config.
Sorry for inconvenience.
** ! Tools to write extracted embedded file are not supported ! **
You must use the liveusb/CD for it's first installation!!!.

Install from scratch notes
======================
** Embedded.img.xz is only for upgrades by WEBGUI, do not extract and write to any media! **

Download NAS4Free livecd or liveusb and boot from it.
The compressed LiveUSB.img.gz needs to be extracted before you can write it to usb media,
you can use it with Win32DiskImager or any other tool.
Press 9 for the install menu and perform an embedded installation.

Upgrade note:
============
You must associate CARP with physical interface explicitly after upgrading to 10.X. to 10.2.
You may need modifying your NFS and AFP share setting.
You may need modifying your ftp setting, no longer SSL is supported (only TLS).
Send Buffer Size/Receive Buffer Size in CIFS/SMB is changed to 128480 since 9.3.0.2.1375.
/var and /var/tmp size has changed.
After the upgrade please do make a new backup of your config System|Backup/Restore.

ZFS User note!
After upgrading, you must re-sync ZFS configuration from Disks|ZFS|Configuration|Synchronize.

Requirements
============
Embedded: 2GB CF/USB/SSD (NAS4free "Embedded" is Recommended Install)
Full: 4GB HDD/SSD (For developers and some advanced users, Not Recommended!)
Swap less: physical memory 2GB or higher needed.
With swap: physical memory 512MB + swap 512MB (swap 1024MB recommended).

*Note: LiveCD is not supported on swap mode except installation and upgrading.

BUILD 10.2.0.2.2545
=================
Changes:
- Upgrade to FreeBSD 10.2-RELEASE-P14.
- Add Mellanox ConnectX-2 EN driver module. (x64 only)
- Add Auxiliary parameters in Samba AD.
- Add bhyve and related files. (CLI only)
- Add hint.acpi_throttle.0.disabled="0", hint.p4tcc.0.disabled="0".
- Add dlna user and group.
- Add minidlna.
- Add VirtualBox with WebSocket VNC server. (x86 and x64 only)
- Add phpVirtualBox and noVNC(HTML5/WebSocket VNC client) for VM management.
- Add ability to mount exFAT disk.
- Add samba local group.
- Add ability to add tap device on bridge interface.
- Add console fonts and keymaps.
- Add keymap setting/restart WebGUI in console menu.
- Add quirk for Silicon Power 16GB and more.
- Add allow group when local users only mode on FTP service.
- Add RRDtool and related files.
- Add mapping DOS attributes on CIFS/SMB. (OFF by default)
- Add various daemon/utility/debug tools for future development.
- Add hosts allow on console menu.
- Add autoresize on SD image. (ARM only)
- Add sendmail_path to php.ini to use mail() function.
- Add auto start/stop VM. (virtualbox)
- Add syncthing and related user and group.
- Add a part of Xen dom0 edition.
- Add vfs.zfs.arc_max, vfs.zfs.arc_min, vfs.zfs.prefetch_disable.
- Add IPMItool needs ipmi_load enabled in System|Advanced|loader.conf.
- Add volblocksize on ZFS volume creation.
- Add volmode on ZFS volume.
- Add ability AFP compatibility per share.
- Add accept remote syslog message.
- Add disable compress same syslog message.
- Add gpart show on Diagnostics|Information|Partitions.
- Add function to enable SMART Monitoring of SMART capable & enabled devices on import.
- Add date/time format selection.
- Remove usesendfile on CIFS/SMB.
- Remove legacy disk aliases such as /dev/ad0.
- Change some WebGUI menus and update text strings.
- Change DSA private key to RSA private key on SSH service.
- Change ZFS pool info reflected from zpool list.
- Change Store DOS attributes to OFF by default.
- Change var/tmpfs size to 512MB/256MB.
- Change empty bridge is allowd.
- Change iscsi initiator. (iscontrol -> iscsictl)
- Upgrade bash 4.3 to patch 42.
- Upgrade isboot to 0.2.13.
- Upgrade mDNSResponder to 576.30.4.
- Upgrade dmidecode to 3.0.
- Upgrade dialog to 1.2-20150920.
- Upgrade xmd to 0.5.
- Upgrade tmux to 2.1.
- Upgrade lighttpd to 1.4.39.
- Upgrade e2fsprogs to 1.42.13.
- Upgrade iperf3 to 3.1.2.
- Upgrade netatalk to 3.1.8.
- Upgrade rsync to 3.1.2.
- Upgrade msmtp to 1.6.4.
- Upgrade nano to 2.5.3.
- Upgrade inadyn-mt to 02.28.04.
- Upgrade transmission to 2.92.
- Upgrade bsnmp-ucd to 0.4.2.
- Upgrade nut to 2.7.4.
- Upgrade proftpd to 1.3.5b.
- Upgrade zoneinfo to 2016c.
- Upgrade php to 5.6.20.
- Upgrade exfat to 1.2.3.
- Upgrade jQuery to 1.12.3.
- Upgrade samba to 4.2.11, this fix BadLock vulnerability (http://badlock.org).
- Upgrade syncthing to 0.12.22.

Fixes:
- Fix typo (ticket #260)
- Fix ZFS volume is not shown in filechooser.
- Fix System status pages shows wrong free space for zfs pools (ticket #271)
- Fix 5000ms page refresh. (took more time than set)
- Fix AFP compatibility don't work if you didn't enable Samaba AD.
- Fix run now on cron don't use Who field.
- Fix duplicate syncthing account when fresh install by 2067.
- Fix broken menu options livecd/liveusb.
- Fix syncthing causes Illegal instruction on old i386. (don't use SSE2)
- Fix VirtualBox cannot be connected via noVNC if using HTTPS.
- Fix bridged member cannot be set IP address.
- Fix minidlna log file location mismatch. (ticket #255)
- Fix smbclient use NT1 instead of SMB3/SMB2. (ticket #236)
- Fix cannot execute samba if time server is empty.
- Fix missing loader parameters on fresh installation. (full only)
- Fix NTFS is not detected on Import disks.
- Fix SSL certificate link. (ticket #239)
- Fix NFS share network. (ticket #238)
- Fix boot time ntpdate fail when AD DC enabled.
- Fix wrong path in Samba AD. (ticket #228, #232)
- Fix rsync does not start/restart on WebGUI.
- Fix send test email when language was changed other than english.
- Fix Undefined symbol "av_find_stream_info" in fuppes/libmetadata_libavformat.so.
- Fix AFP share is not advised.
- Fix webserver user logins.
- Fix wrong path (ticket #228).
- Fix index.php shows wrong time. (ticket 279)
- Fix loader.conf edit.

Note:
- iperf2 has been replaced for iperf3 because of inconsistent results for UDP above 2Gbps.
- iperf3 is not backwards compatible with iperf2.x.

Permanent restrictions:
- It is not possible to format a SoftRAID disk with MSDOS FAT16/32.
- It is not possible to encrypt a disk partition, only complete disks are supported.
- AFP shares with TimeMachine support are limited to max. 4 shares.

Note for new users:
===================

**** The default login for NAS4Free WEBGUI ****

username: admin
password: nas4free

- Change those defaults after setup!

**** phpVitualBox's default login ****

username: admin
password: admin

- Change those default passwords after setup!

wiki virtualbox
http://wiki.nas4free.org/doku.php?id=do ... virtualbox



Regards,
The NAS4Free Team

[zoon01]

Changes after release 10.2.0.2.2445
===================================
- Add syslog level adjustment to proftpd.
- Add webgui cosmetic changes will be default on 10.3 series.
- Cleanup www location put files in order.
- Update translations.
- Upgrade zoneinfo to 2016c.
- Upgrade php to 5.6.20.
- Upgrade exfat to 1.2.3.
- Upgrade jQuery to 1.12.3.
- Upgrade samba to 4.2.11, this fix BadLock vulnerability (http://badlock.org).
- Upgrade syncthing to 0.12.22.
- Fix edit loader.conf.
- Fix executable hast scripts.
Enjoy!

Regards,
zoon01

[zoon01]

Ok, this replaces 2533 and 2535 builds!

this does:
- Upgrade syncthing to 0.12.22.
- Fix edit loader.conf.
- Fix executable hast scripts.

[apollo567]

Btw, I am just running a backup to my NAS-Box and I have the feeling my lagg-Configuration works faster and more balanced.
Might this due to the samba upgrade ???

[provels]

Might be just me, but this blew away my entire config. Password, IPs, ZFS, disks, shares, DLNA, the lot. Will revert to 2535 for now.

[apollo567]

Might be just me, but this blew away my entire config. Password, IPs, ZFS, disks, shares, DLNA, the lot. Will revert to 2535 for now.

Do you have installed embedded Version ? If yes, perhaps a simple restore of the config might solve this

[provels]

Do you have installed embedded Version ? If yes, perhaps a simple restore of the config might solve this

Yes I do. Can I use the backup from a previous version on a newer version? I know they are pretty close.

I already got 2535 back up and can try the upgrade again.

EDIT - OK, after reverting to 2535, I found I had the Extended GUI active. Maybe that's what caused the problem. I disabled it and updated to 2545 again and everything went fine (did not need to restore the 2535 config to the 2545 update).

[apollo567]

Can I use the backup from a previous version on a newer version?

Usually this works !

[Juggler]

After upgrading to 2545 I'm noticing that rsync (local) doesn't start automatically after a reboot. I have to "kickstart" it by going into the rsync local settings then clicking the "execute now" button. Any ideas?

[Offer]

Hello.

It's a long time that the note about "Some features of H.A.S.T are not available in the GUI and requires CLI" is noted in the release notes.

Is there any time estimation for that to be done, and we'll have full High Availibility support for dumm GUI users (like me)?

Many thanks, and please keep the good work!

[ChriZathens]

I am facing a strange issue...
On my Dell Poweredge, I previously had version .2268
Today I decided to upgrade to .2545
Due to the fact that the partition was too small, I performed a clean installation using liveCD
All OK...
But as soon as I restore the configuration, the index page breaks (no bars)

Capture.PNG

Going to System-->General shows an error on the upper side:

Code: Select all

Fatal error: Call to undefined function get_datetime_locale_samples() in /usr/local/www/system.php on line 347

Ans no Save button at the bottom left side

Furthermore, and I will also double post this in the Extended GUI topic, although EGUI's latest version is supposed to work with .2545, once I install it it breaks the index even more with :

Code: Select all

Call to undefined function get_datetime_locale() in /usr/local/www/index.php on line 709

Any ideas???

[ChriZathens]

OK, Later update...
Seems that for some reason my configuration was breaking the web gui...
The same thing happened after restoring the configuration on the latest beta...
I finally ended up configuring the server from scratch (looking at the config file for some settings took me about 10 minutes..)
The disks and the pool, well - of course - imported without a hitch and I am back in business..

[provels]

I was going to suggest dumping the browser cache, but fixed is OK, too!

[ChriZathens]

Hey, thanks for the suggestion, but I had already done that and even tried to access the webui via IE for the first time with the same result.

[Jack Foobar]

This release seems to be the most error free release I've used so far. I'm almost disappointed that I don't have to do anything. It's so boring.

[crest]

Hello again Chris,

OK, Later update...
Seems that for some reason my configuration was breaking the web gui...
The same thing happened after restoring the configuration on the latest beta...
I finally ended up configuring the server from scratch (looking at the config file for some settings took me about 10 minutes..)
The disks and the pool, well - of course - imported without a hitch and I am back in business..

Late answer .... Yes older eGUI Version leads to errors you described but the actual is fully compatible with .2545 (afaik). At a time between .2332 and .2407 there were a lot of changes with impact to the eGUI ... sorry for that!

Regards
Crest

[ChriZathens]

Hey, Andreas, don't worry about it..!!!
In fact I am not even sure that EGUI had something to do with it (hence why I never posted anything in the EGUI topic),
because during my tests I tried to uninstall EGUI altogether prior to the upgrade but I still had issues..
So my final approach was the only thing I could do: Fresh install, install EGUI and RRDgraphs and check the config file in order to set everything back the way it was.
And everything is back to normal again and my RRDgraphs historical data is - of course - intact..
Only took 10-15 minutes..