NAS4Free 10.3.0.3.2898 released (FreeBSD 10.3-RELEASE-P5)

[zoon01]

The NAS4Free Team is pleased to announce the release of version 10.3.0.3.2898 series.

This build replaces 2895 directly because of its lighttpd ipv6 problem.
Sorry for this inconvenience.

Many work and efforts has been put in to make this a great release.
An new ZFS Tools page could not be included on time as it's still under rewrite, but this will be added within 3 weeks we think.
10.3.0.3 is really a huge step above the 10.2 series, we hope you like it like we do!


http://sourceforge.net/projects/nas4fre ... .0.3.2895/

Everyone can upgrade from NAS4Free version 9.3.0.2.1310 or Higher.

README & CHANGELOG

NAS4Free Upgrade from below 9.3.0.2.1310 is NOT possible!!!
=====================================================
Upgrading NAS4Free "Embedded" or "Full" from any version below 9.3.0.2.1310 by webgui or from
LiveCD/USB is problematic, due a new size of boot partition & partition layout.
Please download and save your NAS4Free config and backup all files from second
partition if you do use the boot disk as your data disk too.
INSTALL FROM SCRATCH IS THAN THE ONLY WAY!
After installation you can restore your config and continue using your server.
Sorry for this inconvenience.

Install from scratch notes:
======================
Download NAS4Free livecd or liveusb and boot from it.
The compressed LiveUSB.img.gz needs to be extracted before you can write it to usb media,
you can use it with Win32DiskImager or any other tool.
Press 9 for the install menu and perform an embedded installation.

** Embedded.img.xz is only for upgrades by WEBGUI, do not extract and write to any media for fast installs! **
It will be problematic as it doesn't make the required partitions you do need!

Upgrade note:
============
You must associate CARP with physical interface explicitly after upgrading to 10.X fom 9.3 series.
You may need modifying your NFS and AFP share settings.
You may need modifying your ftp settings, no longer SSL is supported (only TLS).
You may need modifying your ups settings.
You may need to disable virtualbox-ose on 32-bits install first as this is an 64-bits version feature.
After upgrading, you might need to re-sync ZFS configuration from Disks|ZFS|Configuration|Synchronize.
Send Buffer Size/Receive Buffer Size in CIFS/SMB is changed to 128480 since 9.3.0.2.1375.

** After the upgrade please do make a new backup of your configuration! see: System|Backup/Restore on menu **

Syncthing note:
===============
Syncthing 0.14.x versions is included but is incompatible with 0.13.x and 0.12.x versions from 10.2!
Every user that uses Syncthing service should be aware they will have to upgrade all their syncthing clients too.

[EXTENSION] Extended GUI user note:
==================================
ExtendedGUI extension version 0.5.3 or higher is needed for 10.3.0.3 series.
Below 0.5.3 is not compatible, disable than before upgrade.

Requirements:
============
Embedded: 2GB CF/USB/SSD (NAS4free "Embedded" is Recommended Install)
Full: 4GB HDD/SSD (For developers and some advanced users, Not Recommended!)
Swap less: physical memory 2GB or higher needed.
With swap: physical memory 512MB + swap 512MB (swap 1024MB recommended).

*Note: LiveCD is not supported on swap mode except installation and upgrading.

BUILD 10.3.0.3.2898
=================
Changes:
- Upgrade to FreeBSD 10.3-RELEASE-P5.
- Add search function to Diagnostics|Log.
- Add bulk delete action to snapshots and other pages.
- Add configuration option for second UPS system.
- Add configuration option for tls_certcheck.
- Add mounting (read-only) support for EXT4 drives.
- UPS monitoring username & password can be set/changed.
- Update installer now full gpt supported.
- Refactoring Webgui parts and replace deprecated php code.
- sshd Challenge-Response Authentication is now configurable.
- Upgrade exfat to 1.2.3.
- Upgrade phpvirtualbox to 5.0-5.
- Upgrade tmux to 2.2.
- Upgrade fusefs-ntfs to 2016.2.22.
- Upgrade inadyn-mt to 02.28.06.
- Upgrade smartmontools to 6.5.
- Upgrade msmtp to 1.6.5.
- Upgrade iperf3 to 3.1.3.
- Upgrade bash 4.3 to p46.
- Upgrade gzip to 1.8.
- Upgrade jquery to 3.0.0.
- Upgrade unison to 2.48.4.
- Upgrade sudo to 1.8.17p1.
- Upgrade mDNSResponder to 625.41.2.
- Upgrade dialog to 1.3-20160424.
- Upgrade virtualbox-ose to 5.0.24.
- Upgrade nano to 2.6.1.
- Upgrade noVNC to 0.6.1.
- Upgrade zoneinfo to 2016f.
- Upgrade samba to 4.3.11.
- Upgrade jQuery to 3.1.0.
- Upgrade e2fsprogs to 1.43.1.
- Upgrade syncthing to 0.14.0.
- Upgrade php to 7.0.9.
- Upgrade netatalk to 3.1.9.
- Upgrade virtualbox-ose to 5.0.26.

Fixes:
- Fix prevent deletion of mounted gconcat softraid.
- Fix broken shadow copy.
- Fix for rsync over ssh (without deamon).
- Fix dataset did not always get destroyed on webgui if a share is in usage.
- Fix missing mimes (translation files) for File Manager (translating needed).
- Fix firewall rules cannot be moved into the preset rule area.
- Fix disable fw button not working under certain conditions.
- Fix importing ZFS datasets and ZFS volumes from different ZFS pools.
- Fix code format for Swedish file manager.
- Fix gettext protection against html code injections.
- Fix issue when reformatting disks.
- Fix a problem with gpt/labels.
- Fix Some HGST drive temperatures are not displayed.
- Fix download log files did not always work with some browsers.
- Fix some code errors on System|Advanced|Swap.
- Fix broken log files downloads.
- Fix test emails could not send as in French WebGUI.

Permanent Restrictions:
- It is not possible to use virtualbox-ose on 32-bits nas4free, 64-bits only feature.
- It is not possible to format a SoftRAID disk with MSDOS FAT16/32.
- It is not possible to encrypt a disk partition, only complete disks are supported.
- AFP shares with TimeMachine support are limited to max. 4 shares.
- iperf3 is not backwards compatible with iperf2.x. so you might also upgrade your client.

Note for new users:
===================

**** The default login for NAS4Free WEBGUI ****

username: admin
password: nas4free

- Change those defaults after setup!

**** phpVitualBox's default login ****

username: admin
password: admin

- Change those default passwords after setup!

wiki virtualbox
http://wiki.nas4free.org/doku.php?id=do ... virtualbox



Regards,
The NAS4Free Team

[zoon01]

Changes after release 10.3.0.3.2870
===============================
- Add enable advancedconfig option for phpvirtualbox.
- Upgrade jQuery to 3.1.0.
- Upgrade e2fsprogs to 1.43.1.
- Upgrade syncthing to 0.14.0.
- Upgrade php to 7.0.9.
- Upgrade netatalk to 3.1.9.
- Upgrade virtualbox-ose to 5.0.26.
- Update translations.
- Update installer menus, OS/GPT now preferred.
- Add mounting (read-only) support for EXT4 drives.

Enjoy!

Regards,
zoon01

[lindsay]

Installed and looking good so far

[Andrey_BAM]

post report dont send
when you press the send occurs instead of sending preservation - "The changes have been applied successfully."

but scheduled report went fine.

[wingenieur]

Thank you!
Works nicely so far...

[zoon01]

Andrey_BAM

We are not able to reproduce your error
did you setup email in advanced setup correctly, did you press correct button?
it's a bit hard for me to understood your problem.

[zoon01]

Extended Gui users can use/upgrade to 0.5.3 on 10.3.0.3 series now too.

[carloskar]

I upgraded from 10.2.0.2.2433 and SSH stopped working.
I have added some extra options in the Services|SSH, ending it all with a "Match User fake" and I get the following error when trying to start sshd:

Code: Select all

Directive ´ChallengeResponseAuthentication' is not allowed within a Match block

In /etc/ssh/sshd_config I see that two extra lines have been added after my extra options:

Code: Select all

ChallengeResponseAuthentication no
AllowTcpForwarding no

The same two options are also above my extra options, and if I remove my extra options those two lines are in sshd_config twice where the first two occurrences follow the status on the checkboxes on the Services|SSH page.

[carloskar]

I upgraded from 10.2.0.2.2433 and SSH stopped working.
I have added some extra options in the Services|SSH, ending it all with a "Match User fake" and I get the following error when trying to start sshd:

Code: Select all

Directive ´ChallengeResponseAuthentication' is not allowed within a Match block

In /etc/ssh/sshd_config I see that two extra lines have been added after my extra options:

Code: Select all

ChallengeResponseAuthentication no
AllowTcpForwarding no

The same two options are also above my extra options, and if I remove my extra options those two lines are in sshd_config twice where the first two occurrences follow the status on the checkboxes on the Services|SSH page.

I fixed it by modifying /etc/rc.d/sshd, I moved the challengeresponseauthentication and tcpforwarding checks outside of the

Code: Select all

-m "//sshd"

block:

Code: Select all

-i "count(//sshd/challengeresponseauthentication) = 0" -o "ChallengeResponseAuthentication no" -n -b \
-i "count(//sshd/challengeresponseauthentication) > 0" -o "ChallengeResponseAuthentication yes" -n -b \
-i "count(//sshd/port) > 0" -v "concat('Port ',//sshd/port)" -n -b \
-i "count(//sshd/tcpforwarding) > 0" -o "AllowTcpForwarding yes" -n -b \
-i "count(//sshd/tcpforwarding) = 0" -o "AllowTcpForwarding no" -n -b \

I don't know if this is the correct solution but it worked, but unfortunately I'm running an embedded install...

[ChriZathens]

Last night I decided to upgrade my main NAS (was still on 9.3.0.2 v1955)
I downloaded the image file and just to be sure I also downloaded the live CD image in order to perform a clean installation if something went wrong.
Well, nothing went wrong , the img upgraded just fine and all looks good so far!
Another great job from our devs!

[ms49434]

I upgraded from 10.2.0.2.2433 and SSH stopped working.
I have added some extra options in the Services|SSH, ending it all with a "Match User fake" and I get the following error when trying to start sshd:

Code: Select all

Directive ´ChallengeResponseAuthentication' is not allowed within a Match block

In /etc/ssh/sshd_config I see that two extra lines have been added after my extra options:

Code: Select all

ChallengeResponseAuthentication no
AllowTcpForwarding no

The same two options are also above my extra options, and if I remove my extra options those two lines are in sshd_config twice where the first two occurrences follow the status on the checkboxes on the Services|SSH page.

I fixed it by modifying /etc/rc.d/sshd, I moved the challengeresponseauthentication and tcpforwarding checks outside of the

Code: Select all

-m "//sshd"

block:

Code: Select all

-i "count(//sshd/challengeresponseauthentication) = 0" -o "ChallengeResponseAuthentication no" -n -b \
-i "count(//sshd/challengeresponseauthentication) > 0" -o "ChallengeResponseAuthentication yes" -n -b \
-i "count(//sshd/port) > 0" -v "concat('Port ',//sshd/port)" -n -b \
-i "count(//sshd/tcpforwarding) > 0" -o "AllowTcpForwarding yes" -n -b \
-i "count(//sshd/tcpforwarding) = 0" -o "AllowTcpForwarding no" -n -b \

I don't know if this is the correct solution but it worked, but unfortunately I'm running an embedded install...

Hi,
according to https://www.freebsd.org/cgi/man.cgi?sshd_config(5) challengeresponseauthentication option is not allowed within a match block.
The resulting config file created by /etc/rc.d/sshd can be found in /var/etc/ssh/sshd_config.
I hope it helps you to locate the error in your configuration.

[carloskar]

Hi,
according to https://www.freebsd.org/cgi/man.cgi?sshd_config(5) challengeresponseauthentication option is not allowed within a match block.
The resulting config file created by /etc/rc.d/sshd can be found in /var/etc/ssh/sshd_config.
I hope it helps you to locate the error in your configuration.

Yes.

The problem is that the sshd script adds double entries for ChallengeResponseAuthentication and AllowTcpForwarding.
If I remove my extra options then the sshd_config looks like this (I have TCP forwarding enabled in the GUI):

Code: Select all

ChallengeResponseAuthentication no
AllowTcpForwarding yes
ChallengeResponseAuthentication no
AllowTcpForwarding no

Notice that this will work as intended since the first occurrence of a configuration parameter is always used, if the same parameter occurs several times in sshd_config then the first will be used and the rest will be ignored. So as long as you don't use a "Match" block in the extra options it will work.

If I add a commented line in the extra options then the sshd_config looks like this:

Code: Select all

ChallengeResponseAuthentication no
AllowTcpForwarding yes
# My commented line
ChallengeResponseAuthentication no
AllowTcpForwarding no

If I remove the line "-i "count(tcpforwarding) = 0" -o "AllowTcpForwarding no" -n -b \" from sshd script then the sshd_config looks like this:
If I add a commented line in the extra options then the sshd_config looks like this:

Code: Select all

ChallengeResponseAuthentication no
AllowTcpForwarding yes
# My commented line
ChallengeResponseAuthentication no

If I remove the line "-i "count(challengeresponseauthentication) > 0" -o "ChallengeResponseAuthentication yes" -n -b \" then the sshd_config looks like this:

Code: Select all

AllowTcpForwarding yes
# My commented line

So I'd say that it is definitely a problem with the sshd-script.
But what does the sshd_config look like for you others? Do you also have the duplicates?
Has the sshd script changed since 10.2.0.2?

If I move the lines to outside the "-m "//sshd"" block then I get the correct sshd_config:

Code: Select all

ChallengeResponseAuthentication no
AllowTcpForwarding yes
# My commented line

[Victek]

Hi all,
This message appeared for first time since I'm running nas4free with 10.3 versions in my server. I'm running dual network interface in LCAP and it looks that trunk stop working random, later is recovered without any aparent reason ... the switch log shows nothing... Netgear GS108T.

Code: Select all

transmission-daemon[2331]: Couldn't connect socket 54 to 212.225.xxx.xxx, port 51413 (errno 50 - Network is down) (net.c:290)
Jul 28 05:52:19	victekserver	kernel: em0: Interface stopped DISTRIBUTING, possible flapping
Jul 28 05:52:16	victekserver	devd: Executing '/etc/rc.d/dhclient quietstart re0'
Jul 28 05:52:16	victekserver	kernel: re0: link state changed to UP
Jul 28 05:51:54	victekserver	kernel: re0: link state changed to DOWN
Jul 28 05:51:41	victekserver	devd: Executing '/etc/rc.d/dhclient quietstart re0'
Jul 28 05:51:41	victekserver	kernel: re0: link state changed to UP
Jul 28 05:51:34	victekserver	kernel: re0: link state changed to DOWN

Code: Select all

$ ifconfig lagg0
lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	options=209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC>
	ether 40:8d:5c:xx:xx:xx
	inet 10.10.2.4 netmask 0xffffff00 broadcast 10.10.2.255 
	nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
	media: Ethernet autoselect
	status: active
	laggproto lacp lagghash l2,l3,l4
	laggport: re0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING>
	laggport: em0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING>

Code: Select all

$ sysctl -a | grep lacp
net.link.lagg.lacp.default_strict_mode: 1
net.link.lagg.lacp.debug: 0

Comments will be apreciated, Cheers!

[apollo567]

continuation of : viewtopic.php?f=78&t=11096
and crowi's suggestion : https://forums.freenas.org/index.php?th ... ate.27858/

I upgraded now my PC to Windows 10, the Acronis backup software to the latest version and N4F to 2898.
When I do the Backup (normal compression, 128 bit AES encryption in Acronis running at source) I get an average transfer speed of 50 MB/s , CPU usage on Source and Target is far away from full load. When the backup is finished I do a validation run of the backup and then the read speed of the Backup from the NAs (to compare it with the Backup source) the performance breaks down to around 6-7 MB/s, CPU load is on both CPUs quite low.
Whats wrong here ? BTW I use still SMB1 as I have a Mediaplayer in the Network which only can access the NAS with SMB1, until recently this worked quite well for me, but a validation run lasting around two days for the backup is not reasonable anymore.

[Jack Foobar]

Samba/CIFS only enabled server. Seeing this error repeat - didn't know NAS4Free had a printer option.

smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:37.444219, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:37.444025, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)
smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:24.229041, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:24.228957, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)

[scardig]

Samba/CIFS only enabled server. Seeing this error repeat - didn't know NAS4Free had a printer option.

smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:37.444219, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:37.444025, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)
smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:24.229041, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:24.228957, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)

Confirmed. Seems (not thoroughly tested) to be triggered when shares are being accessed by clients older than Windows 10. Also:

Code: Select all

smbd[57395]: [2016/08/01 17:04:28.550244, 1] ../source3/smbd/service.c:560(make_connection_snum)
smbd[57395]: create_connection_session_info failed: NT_STATUS_ACCESS_DENIED
smbd[57395]: [2016/08/01 17:35:07.279611, 1] ../source3/smbd/service.c:560(make_connection_snum)
smbd[57395]: create_connection_session_info failed: NT_STATUS_ACCESS_DENIED

[Jack Foobar]

Samba/CIFS only enabled server. Seeing this error repeat - didn't know NAS4Free had a printer option.

smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:37.444219, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:37.444025, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)
smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:24.229041, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:24.228957, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)

Confirmed. Seems (not thoroughly tested) to be triggered when shares are being accessed by clients older than Windows 10. Also:

Code: Select all

smbd[57395]: [2016/08/01 17:04:28.550244, 1] ../source3/smbd/service.c:560(make_connection_snum)
smbd[57395]: create_connection_session_info failed: NT_STATUS_ACCESS_DENIED
smbd[57395]: [2016/08/01 17:35:07.279611, 1] ../source3/smbd/service.c:560(make_connection_snum)
smbd[57395]: create_connection_session_info failed: NT_STATUS_ACCESS_DENIED

And let me add to that with this as well:

smbd[6865]: Oplock break failed for file Drivers/WSUS/client/w61-x64/glb/IE11-Windows6.1-x64-de-de.exe -- replying anyway
smbd[6865]: [2016/07/31 00:37:30.700345, 0] ../source3/smbd/oplock.c:701(oplock_timeout_handler)
smbd[5847]: Oplock break failed for file Drivers/WSUS/client/w61-x64/glb/IE11-Windows6.1-x64-en-us.exe -- replying anyway
smbd[5847]: [2016/07/31 00:34:42.975152, 0] ../source3/smbd/oplock.c:701(oplock_timeout_handler)

I'm running a WSUS Offline server on here and it freaks out a bit for some reason.

And in addition via Win7 clients:

smbd[2503]: receive_smb_raw_talloc failed for client ipv4:10.0.0.181:60010 read error = NT_STATUS_CONNECTION_RESET.
smbd[2503]: [2016/07/30 16:39:09.922993, 1] ../source3/smbd/process.c:554(receive_smb_talloc)
smbd[2501]: receive_smb_raw_talloc failed for client ipv4:10.0.0.181:60000 read error = NT_STATUS_CONNECTION_RESET.
smbd[2504]: receive_smb_raw_talloc failed for client ipv4:10.0.0.181:60008 read error = NT_STATUS_CONNECTION_RESET.
smbd[2504]: [2016/07/30 16:39:09.868778, 1] ../source3/smbd/process.c:554(receive_smb_talloc)
smbd[2501]: [2016/07/30 16:39:09.868784, 1] ../source3/smbd/process.c:554(receive_smb_talloc)
smbd[2496]: receive_smb_raw_talloc failed for client ipv4:10.0.0.181:59992 read error = NT_STATUS_CONNECTION_RESET.
smbd[2496]: [2016/07/30 16:39:08.894707, 1] ../source3/smbd/process.c:554(receive_smb_talloc)
smbd[2499]: receive_smb_raw_talloc failed for client ipv4:10.0.0.181:59998 read error = NT_STATUS_CONNECTION_RESET.
smbd[2499]: [2016/07/30 16:39:08.870335, 1] ../source3/smbd/process.c:554(receive_smb_talloc)

Samba is just being a miserable PITA with this release. Likely a security update that is making it crap itself.

[kenZ71]

I see the print error as well.

Samba had been difficult for quite a while. Would like to replace but no option for Windows

[Jack Foobar]

And to add to the awesome of samba in this revision, my Gig network is now topping out at 12 MB/s writes.

[sleid]

Samba/CIFS only enabled server. Seeing this error repeat - didn't know NAS4Free had a printer option.

smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:37.444219, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:37.444025, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)
smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:24.229041, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:24.228957, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)

Hello,
Did you activate the firewall of Nas4Free?

[provels]

And to add to the awesome of samba in this revision, my Gig network is now topping out at 12 MB/s writes.

FWIW, I'm getting about 85 MB/s with my Pentium 4/SATA150 5400 RPM drives, machine in sig and just a Netgear GS108. I only use SMB/CIFS and MiniDLNA and all seems to work fine. No SSH prob.

Text or ISO File - Write 85 MBs, Read 55 MBs

Client SSD <-> Realtek <-> GS108 <-> Broadcom <-> Nas4Free WD Red

Is AIO and Large Read/Write enabled in Services|CIFS/SMB|Settings?

[zoon01]

Samba/CIFS only enabled server. Seeing this error repeat - didn't know NAS4Free had a printer option.

smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:37.444219, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:37.444025, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)
smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:24.229041, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:24.228957, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)

Hello,
Did you activate the firewall of Nas4Free?

Short solution: set Samba logging to normal logging, this should be fixed in samba itself more upstream.
Not much we can do, or simply ignore this.

[Jack Foobar]

Samba/CIFS only enabled server. Seeing this error repeat - didn't know NAS4Free had a printer option.

smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:37.444219, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:37.444025, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)
smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:24.229041, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:24.228957, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)

Hello,
Did you activate the firewall of Nas4Free?

The firewall is not enabled. It's 2 routers deep on a local LAN. No need to do so.

[Jack Foobar]

And to add to the awesome of samba in this revision, my Gig network is now topping out at 12 MB/s writes.

FWIW, I'm getting about 85 MB/s with my Pentium 4/SATA150 5400 RPM drives, machine in sig and just a Netgear GS108. I only use SMB/CIFS and MiniDLNA and all seems to work fine. No SSH prob.

Text or ISO File - Write 85 MBs, Read 55 MBs

Client SSD <-> Realtek <-> GS108 <-> Broadcom <-> Nas4Free WD Red

Is AIO and Large Read/Write enabled in Services|CIFS/SMB|Settings?

I have AIO and large r/w enabled, yes. Default S/R buffer of 128480. I also saw 85-114 MB speeds on 9.x and 10.2. This one is giving me real problems though. And it's a embedded system, so I can't really troubleshoot the thing. Just have to hope for the best in the next release.

I really hate windows. Much prefer NFS, but those monkeys won't budge. They just keep making samba more complicated.

[sleid]

Samba/CIFS only enabled server. Seeing this error repeat - didn't know NAS4Free had a printer option.

smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:37.444219, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:37.444025, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)
smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:24.229041, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:24.228957, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)

Hello,
Did you activate the firewall of Nas4Free?

The firewall is not enabled. It's 2 routers deep on a local LAN. No need to do so.

Did you enable "Zeroconf/Bonjour to advertise services of this device" ? (System|Advanced Setup)

[Jack Foobar]

Samba/CIFS only enabled server. Seeing this error repeat - didn't know NAS4Free had a printer option.

smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:37.444219, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:37.444025, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)
smbd[11029]: pcap cache not loaded
smbd[11029]: [2016/07/31 20:25:24.229041, 1] ../source3/smbd/server_reload.c:69(delete_and_reload_printers)
smbd[11029]: Failed to fetch record!
smbd[11029]: [2016/07/31 20:25:24.228957, 1] ../source3/printing/printer_list.c:234(printer_list_get_last_refresh)

Hello,
Did you activate the firewall of Nas4Free?

The firewall is not enabled. It's 2 routers deep on a local LAN. No need to do so.

Did you enable "Zeroconf/Bonjour to advertise services of this device" ? (System|Advanced Setup)

Yes, it has been enabled since I started using Nas4Free. Are you thinking network/DNS flapping?

[sleid]

yes, i had enable firewall with a rule "wan deny all "on my nas, and seeing this error repeat, allow bidirectional udp mdns port rule solve the problem.

mdns
UDP ip:224.0.0.251 port:5353

[Jack Foobar]

yes, i had enable firewall with a rule "wan deny all "on my nas, and seeing this error repeat, allow bidirectional udp mdns port rule solve the problem.

mdns
UDP ip:224.0.0.251 port:5353

It maybe something along those lines. Doing an iperf3 test from a linux box:

Client to Nas4Free Server:

[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.00 sec 97.9 MBytes 821 Mbits/sec 0 409 KBytes
[ 4] 1.00-2.00 sec 96.4 MBytes 809 Mbits/sec 0 409 KBytes
[ 4] 2.00-3.00 sec 96.0 MBytes 805 Mbits/sec 0 409 KBytes
[ 4] 3.00-4.00 sec 95.6 MBytes 802 Mbits/sec 0 409 KBytes
[ 4] 4.00-5.00 sec 96.3 MBytes 807 Mbits/sec 0 409 KBytes
[ 4] 5.00-6.00 sec 95.9 MBytes 804 Mbits/sec 0 409 KBytes
[ 4] 6.00-7.00 sec 96.7 MBytes 811 Mbits/sec 0 409 KBytes
[ 4] 7.00-8.00 sec 95.7 MBytes 803 Mbits/sec 0 409 KBytes
[ 4] 8.00-9.00 sec 96.4 MBytes 809 Mbits/sec 0 409 KBytes
[ 4] 9.00-10.00 sec 95.9 MBytes 805 Mbits/sec 0 409 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.00 sec 963 MBytes 808 Mbits/sec 0 sender
[ 4] 0.00-10.00 sec 961 MBytes 806 Mbits/sec receiver

Nas4Free Server to Client:

[ 4] local 10.0.0.100 port 64051 connected to 10.0.0.181 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.00 sec 80.1 MBytes 672 Mbits/sec 77 126 MBytes
[ 4] 1.00-2.00 sec 80.4 MBytes 674 Mbits/sec 40 172 MBytes
[ 4] 2.00-3.00 sec 80.9 MBytes 679 Mbits/sec 24 482 MBytes
[ 4] 3.00-4.00 sec 80.9 MBytes 679 Mbits/sec 24 632 MBytes
[ 4] 4.00-5.00 sec 80.9 MBytes 679 Mbits/sec 24 682 MBytes
[ 4] 5.00-6.00 sec 80.9 MBytes 679 Mbits/sec 24 40.0 MBytes
[ 4] 6.00-7.00 sec 80.9 MBytes 678 Mbits/sec 25 72.0 MBytes
[ 4] 7.00-8.00 sec 80.9 MBytes 679 Mbits/sec 24 436 MBytes
[ 4] 8.00-9.00 sec 80.9 MBytes 679 Mbits/sec 25 176 MBytes
[ 4] 9.00-10.00 sec 80.9 MBytes 679 Mbits/sec 24 642 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.00 sec 808 MBytes 678 Mbits/sec 311 sender
[ 4] 0.00-10.00 sec 807 MBytes 677 Mbits/sec receiver

Both systems have SSD's and Intel server NIC's. I get the feeling I'll have to reload the config. Something in this upgrade path isn't making it happy.

[maarten]

What has happened to SAMBA?
It has become very very slow (unsuable), approx. <5% (!!) of the speed it used to be....

[Jack Foobar]

I think I'm getting closer to figuring out what's up. After going to System/Advanced, and disabling outbound Firmware update check(supposedly only updates at login), my speeds have picked up. I'm wondering if something under the Samba/udp/ip hood is confusing the WAN with the LAN. It's still not great, but it's not 12 MB/s now either. I just think this build is extremely wonky on the samba side of things. I don't see how a outbound check could affect samba though. Hard to diagnose voodoo, so take that anecdotally.