This is the old XigmaNAS forum in read only mode,
it will taken offline by the end of march 2021!


I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!

"no pools available" <- will donate you your favorite charity!

Problems, solutions, software
Forum rules
• Set-Up Guide • FAQs • Forum Rules
Post Reply
Bster13
NewUser
NewUser
Posts: 7
Joined: 11 Mar 2013 01:04
Status: Offline

"no pools available" <- will donate you your favorite charity!

Post by Bster13 »

{Yes, I will donate $50 to your favorite charity if I can get my data back, I'm in over my head and would gladly give for assistance}

I haven't booted up my single nas4free RAIDZ server in a while and while configuring a second server to back it up to, I powered on my primary to transfer files and saw something similar to this picture from another thread except it displayed this error message for ada02, ada03, and da0:
Image

I did clear configs and import disks and there was no more red on the screen, but I noticed this:

Image

I then clicked on the URL for "unknown" and it states: "no pools available."

In the dmesg output below you'll see ada02 is having trouble, and sometimes zpool import shows all drives are online and working and other times it shows this:

Code: Select all

$ zpool import
   pool: ZPool1
     id: 13178619544119044110
  state: DEGRADED
 status: One or more devices are missing from the system.
 action: The pool can be imported despite missing or damaged devices.  The
	fault tolerance of the pool may be compromised if imported.
   see: http://illumos.org/msg/ZFS-8000-2Q
 config:

	ZPool1                   DEGRADED
	  raidz1-0               DEGRADED
	    ada0                 ONLINE
	    ada1                 ONLINE
	    3357018873082393895  UNAVAIL  cannot open
	    ada3                 ONLINE
***I have not rebooted, and I'm unsure what to do at this point. Any help would be appreciated. Thx.
dmesg output:

Code: Select all

$ dmesg
Copyright (c) 1992-2015 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.2-RELEASE-p7 #0 r291009M: Wed Nov 18 05:50:00 CET 2015
    root@dev.nas4free.org:/usr/obj/nas4free/usr/src/sys/NAS4FREE-amd64 amd64
FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
CPU: AMD A6-6400K APU with Radeon(tm) HD Graphics    (3892.80-MHz K8-class CPU)
  Origin="AuthenticAMD"  Id=0x610f31  Family=0x15  Model=0x13  Stepping=1
  Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
  Features2=0x3e98320b<SSE3,PCLMULQDQ,MON,SSSE3,FMA,CX16,SSE4.1,SSE4.2,POPCNT,AESNI,XSAVE,OSXSAVE,AVX,F16C>
  AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM>
  AMD Features2=0x1ebbfff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,XOP,SKINIT,WDT,LWP,FMA4,TCE,NodeId,TBM,Topology,PCXC,PNXC>
  Structured Extended Features=0x8<BMI1>
  SVM: NP,NRIP,VClean,AFlush,DAssist,NAsids=65536
  TSC: P-state invariant, performance statistics
real memory  = 8589934592 (8192 MB)
avail memory = 7382069248 (7040 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <ALASKA A M I>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
 cpu0 (BSP): APIC ID: 16
 cpu1 (AP): APIC ID: 17
WARNING: VIMAGE (virtualized network stack) is a highly experimental feature.
ACPI BIOS Warning (bug): Optional FADT field Pm2ControlBlock has zero address or length: 0x0000000000000000/0x1 (20150515/tbfadt-673)
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
random: <Software, Yarrow> initialized
cryptosoft0: <software crypto> on motherboard
acpi0: <ALASKA A M I> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <base peripheral, IOMMU> at device 0.2 (no driver attached)
vgapci0: <VGA-compatible display> port 0xf000-0xf0ff mem 0xc0000000-0xcfffffff,0xfef00000-0xfef3ffff irq 17 at device 1.0 on pci0
vgapci0: Boot video device
hdac0: <ATI (0x9902) HDA Controller> mem 0xfef44000-0xfef47fff irq 18 at device 1.1 on pci0
hdac0: hdac_get_capabilities: Invalid corb size (0)
device_attach: hdac0 attach returned 6
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0
pci1: <ACPI PCI bus> on pcib1
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0xd0004000-0xd0004fff,0xd0000000-0xd0003fff irq 16 at device 0.0 on pci1
re0: Using 1 MSI-X message
re0: turning off MSI enable bit.
re0: Chip rev. 0x2c800000
re0: MAC rev. 0x00100000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy0:  none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re0: Using defaults for TSO: 65518/35/2048
re0: Ethernet address: d4:3d:7e:be:f6:33
xhci0: <XHCI (generic) USB 3.0 controller> mem 0xfef4a000-0xfef4bfff irq 18 at device 16.0 on pci0
xhci0: 32 bytes context size, 64-bit DMA
usbus0 on xhci0
xhci1: <XHCI (generic) USB 3.0 controller> mem 0xfef48000-0xfef49fff irq 17 at device 16.1 on pci0
xhci1: 32 bytes context size, 64-bit DMA
usbus1 on xhci1
ahci0: <AMD Hudson-2 AHCI SATA controller> port 0xf190-0xf197,0xf180-0xf183,0xf170-0xf177,0xf160-0xf163,0xf150-0xf15f mem 0xfef51000-0xfef517ff irq 19 at device 17.0 on pci0
ahci0: AHCI v1.30 with 4 6Gbps ports, Port Multiplier supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich3: <AHCI channel> at channel 3 on ahci0
ohci0: <OHCI (generic) USB controller> mem 0xfef50000-0xfef50fff irq 18 at device 18.0 on pci0
usbus2 on ohci0
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfef4f000-0xfef4f0ff irq 17 at device 18.2 on pci0
usbus3: EHCI version 1.0
usbus3 on ehci0
ohci1: <OHCI (generic) USB controller> mem 0xfef4e000-0xfef4efff irq 18 at device 19.0 on pci0
usbus4 on ohci1
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfef4d000-0xfef4d0ff irq 17 at device 19.2 on pci0
usbus5: EHCI version 1.0
usbus5 on ehci1
atapci0: <AMD Hudson-2 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf100-0xf10f irq 17 at device 20.1 on pci0
ata0: <ATA channel> at channel 0 on atapci0
ata1: <ATA channel> at channel 1 on atapci0
hdac0: <Generic (0x780d1022) HDA Controller> mem 0xfef40000-0xfef43fff irq 16 at device 20.2 on pci0
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib2: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci2: <ACPI PCI bus> on pcib2
ohci2: <OHCI (generic) USB controller> mem 0xfef4c000-0xfef4cfff irq 18 at device 20.5 on pci0
usbus6 on ohci2
amdtemp0: <AMD CPU On-Die Thermal Sensors> on hostb4
acpi_button0: <Power Button> on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
ppc1: <Parallel port> port 0x378-0x37f irq 5 drq 3 on acpi0
ppc1: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc1
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: cannot reserve I/O port range
acpi_throttle0: <ACPI CPU Throttling> on cpu0
hwpstate0: <Cool`n'Quiet 2.0> on cpu0
acpi_throttle1: <ACPI CPU Throttling> on cpu1
acpi_throttle1: failed to attach P_CNT
device_attach: acpi_throttle1 attach returned 6
xmd version 0.4.4 by NAS4Free Project (experimental)
xmd: default blocklen 32KB, compression LZ4/LZ4HC, level 6
xmd0: Loaded preload cloop image </mfsroot.uzip> 21661184 bytes at 0xffffffff8211ac60 (128MB disk w/LZ4)
random: unblocking device.
usbus0: 5.0Gbps Super Speed USB v3.0
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
Timecounters tick every 1.000 msec
iSCSI boot driver version 0.2.13
hdacc0: <Realtek ALC887 HDA CODEC> at cad 0 on hdac0
hdaa0: <Realtek ALC887 Audio Function Group> at nid 1 on hdacc0
pcm0: <Realtek ALC887 (Rear Analog)> at nid 20 and 24,26 on hdaa0
pcm1: <Realtek ALC887 (Front Analog)> at nid 27 and 25 on hdaa0
usbus1: 5.0Gbps Super Speed USB v3.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 480Mbps High Speed USB v2.0
usbus6: 12Mbps Full Speed USB v1.0
ugen2.1: <AMD> at usbus2
uhub0: <AMD OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen1.1: <0x1022> at usbus1
uhub1: <0x1022 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus1
ugen0.1: <0x1022> at usbus0
uhub2: <0x1022 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
ugen6.1: <AMD> at usbus6
uhub3: <AMD OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
ugen5.1: <AMD> at usbus5
uhub4: <AMD EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus5
ugen4.1: <AMD> at usbus4
uhub5: <AMD OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen3.1: <AMD> at usbus3
uhub6: <AMD EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
uhub3: 2 ports with 2 removable, self powered
uhub0: 5 ports with 5 removable, self powered
uhub5: 5 ports with 5 removable, self powered
uhub1: 4 ports with 4 removable, self powered
uhub2: 4 ports with 4 removable, self powered
(noperiph:ahcich2:0:-1:ffffffff): rescan already queued
(noperiph:ahcich2:0:-1:ffffffff): rescan already queued
(noperiph:ahcich2:0:-1:ffffffff): rescan already queued
uhub4: 5 ports with 5 removable, self powered
uhub6: 5 ports with 5 removable, self powered
(noperiph:ahcich2:0:-1:ffffffff): rescan already queued
(noperiph:ahcich2:0:-1:ffffffff): rescan already queued
(noperiph:ahcich2:0:-1:ffffffff): rescan already queued
(noperiph:ahcich2:0:-1:ffffffff): rescan already queued
(noperiph:ahcich3:0:-1:ffffffff): rescan already queued
ugen3.2: <JetFlash> at usbus3
umass0: <JetFlash Mass Storage Device, class 0/0, rev 2.00/11.00, addr 2> on usbus3
umass0:  SCSI over Bulk-Only; quirks = 0x8100
umass0:6:0:-1: Attached to scbus6
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
ada0: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada0: Serial Number W1F3J71C
ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytesda0 at umass-sim0 bus 0 scbus6 target 0 lun 0
da0: <JetFlash Transcend 4GB 1100> Removable Direct Access SPC-2 SCSI device
da0: Serial Number 19FJ0GQGEPOR05R5
da0: 40.000MB/s transfers
da0: 3864MB (7913472 512 byte sectors: 255H 63S/T 492C)
da0: quirks=0x12<NO_6_BYTE,NO_RC16>
)
ada0: Command Queueing enabled
ada0: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada0: quirks=0x1<4K>
ada1 at ahcich1 bus 0 scbus1 target 0 lun 0
ada1: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada1: Serial Number W1F3J737
ada1: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada1: quirks=0x1<4K>
hdac1: <ATI (0x9902) HDA Controller> mem 0xfef44000-0xfef47fff irq 18 at device 1.1 on pci0
hdac1: hdac_get_capabilities: Invalid corb size (0)
device_attach: hdac1 attach returned 6
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 1946400128 Hz quality 1000
Trying to mount root from ufs:/dev/xmd0 []...
ada2 at ahcich3 bus 0 scbus3 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J6ZS
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich3 bus 0 scbus3 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J6ZS detached
(ada2:ahcich3:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada3 at ahcich3 bus 0 scbus3 target 0 lun 0
ada3: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada3: Serial Number W1F3J6ZS
ada3: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada3: Command Queueing enabled
ada3: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada3: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
fuse-freebsd: version 0.4.4, FUSE ABI 7.8
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> ACS-2 ATA SATA 3.x device
ada2: Serial Number W1F3J724
ada2: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: quirks=0x1<4K>
ada2 at ahcich2 bus 0 scbus2 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC29> s/n W1F3J724 detached
(ada2:ahcich2:0:0:0): Periph destroyed
Report generator:

Code: Select all

NAS4Free 10.2.0.2 (revision 2067) x64-embedded
ALASKA A M I AMD A6-6400K APU with Radeon(tm) HD Graphics 8192MiB RAM

OHCI (generic) USB controller XHCI (generic) USB 3.0 controller AMD
Hudson-2 UDMA133 controller bus=3 hubaddr=1 port=5 devaddr=2
interface=0 ugen=ugen3.2 RTL8169S/8110S/8211 1000BASE-T media
interface EHCI (generic) USB 2.0 controller
Top
User avatar
ms49434
Developer
Developer
Posts: 828
Joined: 03 Sep 2015 18:49
Location: Neuenkirchen-Vörden, Germany - GMT+1
Contact:
Contact ms49434
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by ms49434 »

you can try to force import the pool: zpool import -f ZPool1
then
replace failed/missing disk: zpool replace ZPool1 3357018873082393895 ada2 (but check if ada2 is correct after the import)
then
sync webgui
1) XigmaNAS 12.1.0.4 amd64-embedded on a Dell T20 running in a VM on ESXi 6.7U3, 22GB out of 32GB ECC RAM, LSI 9300-8i IT mode in passthrough mode. Pool 1: 2x HGST 10TB, mirrored, L2ARC: Samsung 850 Pro; Pool 2: 1x Samsung 860 EVO 1TB, SLOG: Samsung SM883, services: Samba AD, CIFS/SMB, ftp, ctld, rsync, syncthing, zfs snapshots.
2) XigmaNAS 12.1.0.4 amd64-embedded on a Dell T20 running in a VM on ESXi 6.7U3, 8GB out of 32GB ECC RAM, IBM M1215 crossflashed, IT mode, passthrough mode, 2x HGST 10TB , services: rsync.
Top
User avatar
apollo567
Site Admin
Site Admin
Posts: 675
Joined: 23 Jun 2012 06:37
Location: Ludwigshafen, Germany
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by apollo567 »

maybe I'd like to mention, good idea for wanting to devote money to a charity for help, but bear in mind the project is runned by volunteers and the project itself also might need some support ! (see zoons post)
my NAS and its development until today: viewtopic.php?f=63&t=39&sid=039fed830cf ... 4d0abe4a04
Top
Bster13
NewUser
NewUser
Posts: 7
Joined: 11 Mar 2013 01:04
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by Bster13 »

Understood, in my time of panic didn't notice that, but see that now. No problem giving there instead. When I get home from work, I'll give the suggestions a shot. thx.
apollo567 wrote:maybe I'd like to mention, good idea for wanting to devote money to a charity for help, but bear in mind the projects is runed by volunteers and the project itself also might need some support ! (see zoons post)
Top
Bster13
NewUser
NewUser
Posts: 7
Joined: 11 Mar 2013 01:04
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by Bster13 »

Hrmm..the force did not seem to do anything, still reporting no pool.

I did notice this about the disks though, not it appears ada03 is having trouble:

Image

Image

And when I look at the disks just now, I see this:

Image
ms49434 wrote:you can try to force import the pool: zpool import -f ZPool1
then
replace failed/missing disk: zpool replace ZPool1 3357018873082393895 ada2 (but check if ada2 is correct after the import)
then
sync webgui
Top
kenZ71
Advanced User
Advanced User
Posts: 379
Joined: 27 Jun 2012 20:18
Location: Northeast, USA
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by kenZ71 »

Seeing the drives in red under Disks | Management is usually resolved by clicking "Clear config & import disks" followed by Apply.

Then try the zpool import -f ZPool1
11.2-RELEASE-p3 | ZFS Mirror - 2 x 8TB WD Red | 28GB ECC Ram
HP ML10v2 x64-embedded on Intel(R) Core(TM) i3-4150 CPU @ 3.50GHz

Extra memory so I can host a couple VMs
1) Unifi Controller on Ubuntu
2) Librenms on Ubuntu
Top
User avatar
apollo567
Site Admin
Site Admin
Posts: 675
Joined: 23 Jun 2012 06:37
Location: Ludwigshafen, Germany
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by apollo567 »

Doesn't look too bad, seems the missing disk is there.
BTW a RAIDZ Pool which is degraded by only one disk, should still be accessible to backup the data.
I once had also such a problem when I used SATA Cables without a metal latch. Did you move the NAS Box recently ?
my NAS and its development until today: viewtopic.php?f=63&t=39&sid=039fed830cf ... 4d0abe4a04
Top
User avatar
Parkcomm
Advanced User
Advanced User
Posts: 384
Joined: 21 Sep 2012 12:58
Location: Australia
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by Parkcomm »

Hey Bster,

lets go back to basic principles. Command line message showed one disk faulted in which case your data is fine - if two disks are faulted you might be int trouble.

please provide the output of

Code: Select all

zpool status
and

Code: Select all

zpool import -f Zpool1
make sure you include the pool name
NAS4Free Embedded 10.2.0.2 - Prester (revision 2003), HP N40L Microserver (AMD Turion) with modified BIOS, ZFS Mirror 4 x WD Red + L2ARC 128M Apple SSD, 10G ECC Ram, Intel 1G CT NIC + inbuilt broadcom
Top
Bster13
NewUser
NewUser
Posts: 7
Joined: 11 Mar 2013 01:04
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by Bster13 »

Code: Select all

$ zpool status
  pool: ZPool1
 state: DEGRADED
status: One or more devices has been removed by the administrator.
	Sufficient replicas exist for the pool to continue functioning in a
	degraded state.
action: Online the device using 'zpool online' or replace the device with
	'zpool replace'.
  scan: scrub repaired 0 in 0h0m with 0 errors on Mon Aug 15 01:08:57 2016
config:

	NAME                     STATE     READ WRITE CKSUM
	ZPool1                   DEGRADED     0     0     0
	  raidz1-0               DEGRADED     0     0     0
	    ada0                 ONLINE       0     0     0
	    ada1                 ONLINE       0     0     0
	    3357018873082393895  REMOVED      0     0     0  was /dev/ada2
	    ada3                 ONLINE       0     0     0

errors: No known data errors
Then I ran "zpool import -f Zpool1"

Here is what my disks look like after I ran the statys and import commands:
Image

Then I ran:
Image
Top
User avatar
crowi
Forum Moderator
Forum Moderator
Posts: 1176
Joined: 21 Feb 2013 16:18
Location: Munich, Germany
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by crowi »

Check the cables and connections to your drives
NAS 1: Milchkuh: Asrock C2550D4I, Intel Avoton C2550 Quad-Core, 16GB DDR3 ECC, 5x3TB WD Red RaidZ1 +60 GB SSD for ZIL/L2ARC, APC-Back UPS 350 CS, NAS4Free 11.0.0.4.3460 embedded
NAS 2: Backup: HP N54L, 8 GB ECC RAM, 4x4 TB WD Red, RaidZ1, NAS4Free 11.0.0.4.3460 embedded
NAS 3: Office: HP N54L, 8 GB ECC RAM, 2x3 TB WD Red, ZFS Mirror, APC-Back UPS 350 CS NAS4Free 11.0.0.4.3460 embedded
Top
User avatar
apollo567
Site Admin
Site Admin
Posts: 675
Joined: 23 Jun 2012 06:37
Location: Ludwigshafen, Germany
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by apollo567 »

crowi wrote:Check the cables and connections to your drives
+1 !
my NAS and its development until today: viewtopic.php?f=63&t=39&sid=039fed830cf ... 4d0abe4a04
Top
User avatar
raulfg3
Site Admin
Site Admin
Posts: 4865
Joined: 22 Jun 2012 22:13
Location: Madrid (ESPAÑA)
Contact:
Contact raulfg3
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by raulfg3 »

Do You use sata cages?
If yes, use direct sata connection to your hd.
12.1.0.4 - Ingva (revision 7743) on SUPERMICRO X8SIL-F 8GB of ECC RAM, 11x3TB disk in 1 vdev = Vpool = 32TB Raw size , so 29TB usable size (I Have other NAS as Backup)

Wiki
Last changes

HP T510
Top
Bster13
NewUser
NewUser
Posts: 7
Joined: 11 Mar 2013 01:04
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by Bster13 »

Damn, SATA cables cost me $50. :p I reseated them and they came up...I always read SATA cables are junk, etc. but these were all brand new cables and I hadn't messed around inside the case, I don't understand. Anyway, I am going to start the process of copying my data to my backup server pronto and then I will donate $50 to Nas4free. Many thanks for the help, and apologies for not responding sooner as I was away for work. Thanks!
Top
Bster13
NewUser
NewUser
Posts: 7
Joined: 11 Mar 2013 01:04
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by Bster13 »

Ok, maybe I've lost my mind and totally forgot where my data was way back when I set things up, but the server I thought had the data on it, that I've been posted screenshots about (ZPool1), appears to be wiped clean:

Image

And the server I intended to copy data ~to~ with a new config appears to have data hidden somewhere:

Image

I don't recall what the shares were or how anything was mapped in CIFS/WIndows prior. If I don't know the path, how can I access any of the data that may be on either server?
Top
kenZ71
Advanced User
Advanced User
Posts: 379
Joined: 27 Jun 2012 20:18
Location: Northeast, USA
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by kenZ71 »

From a command prompt on the NAS type df -kh which will show space used by mounts, find the largest and start poking around for your data.
11.2-RELEASE-p3 | ZFS Mirror - 2 x 8TB WD Red | 28GB ECC Ram
HP ML10v2 x64-embedded on Intel(R) Core(TM) i3-4150 CPU @ 3.50GHz

Extra memory so I can host a couple VMs
1) Unifi Controller on Ubuntu
2) Librenms on Ubuntu
Top
Bster13
NewUser
NewUser
Posts: 7
Joined: 11 Mar 2013 01:04
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by Bster13 »

Hrmm...not a whole lot there:
$ df -kh
Filesystem Size Used Avail Capacity Mounted on
/dev/xmd0 120M 69M 51M 58% /
devfs 1.0K 1.0K 0B 100% /dev
/dev/xmd1 719M 261M 458M 36% /usr/local
/dev/da0s1a 743M 152M 592M 20% /cf
procfs 4.0K 4.0K 0B 100% /proc
Zpool1 7.7T 140K 7.7T 0% /mnt/Zpool1
/dev/xmd2 248M 3.7M 224M 2% /var
tmpfs 128M 44K 128M 0% /var/tmp
And yet I'm missing a large chunk of my storage:

Image
Top
User avatar
b0ssman
Forum Moderator
Forum Moderator
Posts: 2438
Joined: 14 Feb 2013 08:34
Location: Munich, Germany
Status: Offline

Re: "no pools available" <- will donate you your favorite charity!

Post by b0ssman »

you are not missing storage 1/4 of the storage is used for parity.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
Top
Post Reply

Return to “Data recovery and backups”