Like me on Supermicro X10SL7-F with onboard 2308 chipset we can upgrade the firmware to latest 20.00.07.00. version.
See
ftp://ftp.supermicro.com/driver/SAS/LSI ... rmware/IT/
This is the old XigmaNAS forum in read only mode,
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
Supermicro SAS 2308 firmware 20.00.07.00
-
zoon01
- Developer
- Posts: 724
- Joined: 20 Jun 2012 21:06
- Location: Netherlands
- Contact:
- Status: Offline
Supermicro SAS 2308 firmware 20.00.07.00
System specs: XigmaNAS 11.2.0.4 -embedded on Samsung 860 EVO 256GB and Supermicro X10SL7-F w / Bios v3.2, IPMI v.03.86 / CPU E3-1241 v3 @ 3.50GHz - 32GB Crucial DDR3L 1600mhz ECC 1.35v , LSI 2308 on PH20.00.07.00 IT mode, Storage: 5x Western Digital Red (WD30EFRX) raidz
Development system is same system in virtualbox.
Development system is same system in virtualbox.
-
zoon01
- Developer
- Posts: 724
- Joined: 20 Jun 2012 21:06
- Location: Netherlands
- Contact:
- Status: Offline
Re: Supermicro SAS 2308 firmware 20.00.07.00
Some asked me how i did flash it. below are the steps.
Prepare usb key:
Copy content of extracted PH20.00.07.00-IT\IT\UEFI folder to usb key.
(I use IPMI remote console on desktop).
1. Boot with the usb key inserted and press F11
2. Now select: UEFI: Built-in EFI Shell
3. enter: fs0:
4. enter dir for the usb file list
now you should see the files you did copy to the usb key if correctly done. if not try: enter fs1:
5. enter: sas2flash.efi -listall and/or sas2flash.efi -list and note down last 9 digest of the sas address.
6. now enter SMC2308T.NSH , this will erase the rome and program it after, when done enter the last 9 digest you noted down.
thats all
Prepare usb key:
Copy content of extracted PH20.00.07.00-IT\IT\UEFI folder to usb key.
(I use IPMI remote console on desktop).
1. Boot with the usb key inserted and press F11
2. Now select: UEFI: Built-in EFI Shell
3. enter: fs0:
4. enter dir for the usb file list
now you should see the files you did copy to the usb key if correctly done. if not try: enter fs1:
5. enter: sas2flash.efi -listall and/or sas2flash.efi -list and note down last 9 digest of the sas address.
6. now enter SMC2308T.NSH , this will erase the rome and program it after, when done enter the last 9 digest you noted down.
thats all
System specs: XigmaNAS 11.2.0.4 -embedded on Samsung 860 EVO 256GB and Supermicro X10SL7-F w / Bios v3.2, IPMI v.03.86 / CPU E3-1241 v3 @ 3.50GHz - 32GB Crucial DDR3L 1600mhz ECC 1.35v , LSI 2308 on PH20.00.07.00 IT mode, Storage: 5x Western Digital Red (WD30EFRX) raidz
Development system is same system in virtualbox.
Development system is same system in virtualbox.