I have installed Nas4free BUILD 9.1.0.1.531
From my PC (with Windows XP) I can ping Nas4Free (IP 192.168.1.40) but I can't access the WEBGUI. Firewall is disabled!
From Nas4Free I can ping my PC.
I see that from a bug "WebGUI cannot be accessed" is fixed since 9.0.0.1.228
What I can do now?
thanks
This is the old XigmaNAS forum in read only mode,
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
WebGUI cannot be accessed!
-
raulfg3
- Site Admin
- Posts: 4865
- Joined: 22 Jun 2012 22:13
- Location: Madrid (ESPAÑA)
- Contact:
- Status: Offline
Re: WebGUI cannot be accessed!
default IP is 192.168.1.250 , do you change to 192.168.1.40? , how?
if you change from shell, you need to add gateway and DNS servers too, to ping from NAS to PC.
PD: What Browser do you use?.
if you change from shell, you need to add gateway and DNS servers too, to ping from NAS to PC.
PD: What Browser do you use?.
12.1.0.4 - Ingva (revision 7743) on SUPERMICRO X8SIL-F 8GB of ECC RAM, 11x3TB disk in 1 vdev = Vpool = 32TB Raw size , so 29TB usable size (I Have other NAS as Backup)
Wiki
Last changes
HP T510
Wiki
Last changes
HP T510
-
itmanager
- NewUser
- Posts: 4
- Joined: 04 Dec 2012 13:28
- Status: Offline
Re: WebGUI cannot be accessed!
yes I change IP address, gateway and DNS from shell keyboardraulfg3 wrote:default IP is 192.168.1.250 , do you change to 192.168.1.40? , how?
if you change from shell, you need to add gateway and DNS servers too, to ping from NAS to PC.
PD: What Browser do you use?.
chrome /explorer
-
raulfg3
- Site Admin
- Posts: 4865
- Joined: 22 Jun 2012 22:13
- Location: Madrid (ESPAÑA)
- Contact:
- Status: Offline
Re: WebGUI cannot be accessed!
in some cases is needed to reboot NAS after do this changes, please confirm that you reboot your NAS, and use Firefox until problem is solved.
12.1.0.4 - Ingva (revision 7743) on SUPERMICRO X8SIL-F 8GB of ECC RAM, 11x3TB disk in 1 vdev = Vpool = 32TB Raw size , so 29TB usable size (I Have other NAS as Backup)
Wiki
Last changes
HP T510
Wiki
Last changes
HP T510
-
itmanager
- NewUser
- Posts: 4
- Joined: 04 Dec 2012 13:28
- Status: Offline
Re: WebGUI cannot be accessed!
I have reboted many times but the problem persist.raulfg3 wrote:in some cases is needed to reboot NAS after do this changes, please confirm that you reboot your NAS, and use Firefox until problem is solved.
Now I can't verify with firefox. I will do this tomorrow.
thanks
-
raulfg3
- Site Admin
- Posts: 4865
- Joined: 22 Jun 2012 22:13
- Location: Madrid (ESPAÑA)
- Contact:
- Status: Offline
Re: WebGUI cannot be accessed!
please post result of: ifconfig
12.1.0.4 - Ingva (revision 7743) on SUPERMICRO X8SIL-F 8GB of ECC RAM, 11x3TB disk in 1 vdev = Vpool = 32TB Raw size , so 29TB usable size (I Have other NAS as Backup)
Wiki
Last changes
HP T510
Wiki
Last changes
HP T510
-
itmanager
- NewUser
- Posts: 4
- Joined: 04 Dec 2012 13:28
- Status: Offline
Re: WebGUI cannot be accessed!
...raulfg3 wrote:please post result of: ifconfig
today I boot nas4free and, after all init/booting procedures, nas4free end with the root prompt?!
I have rebooted 3/4 times with same results.
So I have reinstalled Nas4Free and changes the IP address and gateway and DNS...
Now I can browse to 192.168.1.40 and access to webGUI with chrome/explorer and firefox!!!
...but if I add two HD I have problems (missing system disk). But the first disk to boot is right checked in bios!
Now I reinstall all using full installation (and not embedded)