I've recreated my original config. and imported previous zfs pool then I've added nev virtual device 5x3tb drives raidz2 (4kb sectors) and created a new pool.
I've rebooted it few times in the begining to test if everyting came back up and it was ok. I've been using it for about a week (tinkering with parameters for performance and testing it without disabling zil or sync) . Now after a reboot the old pool (not upgraded) is here but new pool (zfspool2) disapeared.
(i've rebooted it few times in the beggining to test if everyting came back up and it was ok)
In gui i have virtual device looking as it should (dont know how to check vdev from command line)
and zfspool 2 has every column unknown.
When i go to tools->detected i see no mention of zfspool2 the drives seem ok(at boot not sure about .nop thingStatus|Disks
I've tried to do
zpool import zfspool2
no pools
zpool import
blank and no new zpool
zpool import -D
nothing.
when i went to disks->management and did the clear config and import disks all drives involved in raidz2 for zfspool2 changed from zfspool device or something like that to unknown or unformatted.
Is there a way to recover from such situation?
I've searched the forum but didnt find any solution.
I dont think data would be corrupted as i've restared the system just after midnight and there was no usage and i think it would be pretty unlikely for it to corrupt all of the raidz2 devices all at once?zpool import zfspool2zpool import zfspool2
Is there an issue with 4k/521B sectors or something ??
I'm quite green when it comes to zfs aand i thread carefullly .... I'm experienced with GNU Linux
here are come information output on original config loaded
Code: Select all
Disks|ZFS|Configuration|Current:
zfspool2 Unknown Unknown (Unknown) Unknown Unknown -
zfspool2_raidz2_1 raidz2 zfspool2 /dev/ada2, /dev/ada3, /dev/ada4, /dev/ada6, /dev/ada7
Code: Select all
Status|Disks
Disk Size Description Device model Serial number File system I/O statistics Temperature Status
ada0 1907730MB WDC WD20EARX-00PASB0 51.0AB51 WDC WD20EARX-00PASB0 WD-WMAZA5301844 ZFS storage pool device 6.54 KiB/t, 1 tps, 0.01 MiB/s 15 °C ONLINE
ada1 1907730MB WDC WD20EARX-00PASB0 51.0AB51 WDC WD20EARX-00PASB0 WD-WMAZA5302980 ZFS storage pool device 6.66 KiB/t, 1 tps, 0.01 MiB/s 16 °C ONLINE
ada2 2861589MB ST3000DM001-1CH166 CC24 ST3000DM001-1CH166 W1F239CV ZFS storage pool device 20.77 KiB/t, 0 tps, 0.00 MiB/s 18 °C ONLINE
ada3 2861589MB ST3000DM001-1CH166 CC24 ST3000DM001-1CH166 W1F24K9C ZFS storage pool device 20.77 KiB/t, 0 tps, 0.00 MiB/s 18 °C ONLINE
ada4 2861589MB ST3000DM001-1CH166 CC24 ST3000DM001-1CH166 W1F24V1J ZFS storage pool device 20.77 KiB/t, 0 tps, 0.00 MiB/s 18 °C ONLINE
ada5 1907730MB WDC WD20EARX-00PASB0 51.0AB51 WDC WD20EARX-00PASB0 WD-WCAZAC159360 ZFS storage pool device 6.77 KiB/t, 1 tps, 0.01 MiB/s 15 °C ONLINE
ada6 2861589MB ST3000DM001-1CH166 CC24 ST3000DM001-1CH166 W1F24T7T ZFS storage pool device 20.77 KiB/t, 0 tps, 0.00 MiB/s 18 °C ONLINE
ada7 2861589MB ST3000DM001-1CH166 CC24 ST3000DM001-1CH166 W1F24PAG ZFS storage pool device 20.77 KiB/t, 0 tps, 0.00 MiB/s 18 °C ONLINE
da0 3701MB pqi IntelligentStick PMAP pqi IntelligentStick PMAP 13AA070D2784A26B5916 UFS 15.05 KiB/t, 0 tps, 0.00 MiB/s n/a ONLINE
Code: Select all
Device /dev/ada0 - WDC WD20EARX-00PASB0 51.0AB51
******* Working on device /dev/ada0 *******
parameters extracted from in-core disklabel are:
cylinders=3876021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=3876021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 3907029105 (1907729 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 180/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/ada1 - WDC WD20EARX-00PASB0 51.0AB51
******* Working on device /dev/ada1 *******
parameters extracted from in-core disklabel are:
cylinders=3876021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=3876021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 3907029105 (1907729 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 180/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/ada2 - ST3000DM001-1CH166 CC24
******* Working on device /dev/ada2 *******
parameters extracted from in-core disklabel are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 1565565057 (764436 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 755/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/ada3 - ST3000DM001-1CH166 CC24
******* Working on device /dev/ada3 *******
parameters extracted from in-core disklabel are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 1565565057 (764436 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 755/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/ada4 - ST3000DM001-1CH166 CC24
******* Working on device /dev/ada4 *******
parameters extracted from in-core disklabel are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 1565565057 (764436 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 755/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/ada5 - WDC WD20EARX-00PASB0 51.0AB51
******* Working on device /dev/ada5 *******
parameters extracted from in-core disklabel are:
cylinders=3876021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=3876021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 3907029105 (1907729 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 180/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/ada6 - ST3000DM001-1CH166 CC24
******* Working on device /dev/ada6 *******
parameters extracted from in-core disklabel are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 1565565057 (764436 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 755/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/ada7 - ST3000DM001-1CH166 CC24
******* Working on device /dev/ada7 *******
parameters extracted from in-core disklabel are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 1565565057 (764436 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 755/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/da0 - pqi IntelligentStick PMAP
******* Working on device /dev/da0 *******
parameters extracted from in-core disklabel are:
cylinders=471 heads=255 sectors/track=63 (16065 blks/cyl)
parameters to be used for BIOS calculations are:
cylinders=471 heads=255 sectors/track=63 (16065 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
<UNUSED>
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 0, size 50000 (24 Meg), flag 80 (active)
beg: cyl 0/ head 0/ sector 1;
end: cyl 1023/ head 254/ sector 63Device /dev/ada0 - WDC WD20EARX-00PASB0 51.0AB51
******* Working on device /dev/ada0 *******
parameters extracted from in-core disklabel are:
cylinders=3876021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=3876021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 3907029105 (1907729 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 180/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/ada1 - WDC WD20EARX-00PASB0 51.0AB51
******* Working on device /dev/ada1 *******
parameters extracted from in-core disklabel are:
cylinders=3876021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=3876021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 3907029105 (1907729 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 180/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/ada2 - ST3000DM001-1CH166 CC24
******* Working on device /dev/ada2 *******
parameters extracted from in-core disklabel are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 1565565057 (764436 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 755/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/ada3 - ST3000DM001-1CH166 CC24
******* Working on device /dev/ada3 *******
parameters extracted from in-core disklabel are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 1565565057 (764436 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 755/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/ada4 - ST3000DM001-1CH166 CC24
******* Working on device /dev/ada4 *******
parameters extracted from in-core disklabel are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 1565565057 (764436 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 755/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/ada5 - WDC WD20EARX-00PASB0 51.0AB51
******* Working on device /dev/ada5 *******
parameters extracted from in-core disklabel are:
cylinders=3876021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=3876021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 3907029105 (1907729 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 180/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/ada6 - ST3000DM001-1CH166 CC24
******* Working on device /dev/ada6 *******
parameters extracted from in-core disklabel are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 1565565057 (764436 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 755/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/ada7 - ST3000DM001-1CH166 CC24
******* Working on device /dev/ada7 *******
parameters extracted from in-core disklabel are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Figures below won't work with BIOS for partitions not in cyl 1
parameters to be used for BIOS calculations are:
cylinders=5814021 heads=16 sectors/track=63 (1008 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 63, size 1565565057 (764436 Meg), flag 80 (active)
beg: cyl 0/ head 1/ sector 1;
end: cyl 755/ head 15/ sector 63
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
<UNUSED>
Device /dev/da0 - pqi IntelligentStick PMAP
******* Working on device /dev/da0 *******
parameters extracted from in-core disklabel are:
cylinders=471 heads=255 sectors/track=63 (16065 blks/cyl)
parameters to be used for BIOS calculations are:
cylinders=471 heads=255 sectors/track=63 (16065 blks/cyl)
Media sector size is 512
Warning: BIOS sector numbering starts with sector 1
Information from DOS bootblock is:
The data for partition 1 is:
<UNUSED>
The data for partition 2 is:
<UNUSED>
The data for partition 3 is:
<UNUSED>
The data for partition 4 is:
sysid 165 (0xa5),(FreeBSD/NetBSD/386BSD)
start 0, size 50000 (24 Meg), flag 80 (active)
beg: cyl 0/ head 0/ sector 1;
end: cyl 1023/ head 254/ sector 63Code: Select all
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.1-RELEASE #0 r246186M: Fri Feb 1 00:21:40 CET 2013
root@dev.nas4free.org:/usr/obj/nas4free/usr/src/sys/NAS4FREE-amd64 amd64
CPU: Intel(R) Core(TM)2 Duo CPU E7400 @ 2.80GHz (2807.02-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x1067a Family = 6 Model = 17 Stepping = 10
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xc08e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,XSAVE,OSXSAVE>
AMD Features=0x20100800<SYSCALL,NX,LM>
AMD Features2=0x1<LAHF>
TSC: P-state invariant, performance statistics
real memory = 4294967296 (4096 MB)
avail memory = 3849969664 (3671 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <7514MS A7514200>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
cryptosoft0: <software crypto> on motherboard
acpi0: <7514MS A7514200> on motherboard
acpi0: Power Button (fixed)
acpi0: reservation of ffc00000, 300000 (3) failed
acpi0: reservation of fee00000, 1000 (3) failed
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, bff00000 (3) failed
cpu0: <ACPI CPU> on acpi0
ACPI Warning: Incorrect checksum in table [OEMB] - 0x85, should be 0x84 (20110527/tbutils-282)
cpu1: <ACPI CPU> on acpi0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 450
Event timer "HPET1" frequency 14318180 Hz quality 440
Event timer "HPET2" frequency 14318180 Hz quality 440
Event timer "HPET3" frequency 14318180 Hz quality 440
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xb000-0xb0ff mem 0xd0000000-0xdfffffff,0xfe8f0000-0xfe8fffff irq 16 at device 0.0 on pci1
vgapci1: <VGA-compatible display> mem 0xfe8e0000-0xfe8effff at device 0.1 on pci1
uhci0: <Intel 82801JI (ICH10) USB controller USB-D> port 0xac00-0xac1f irq 16 at device 26.0 on pci0
uhci0: LegSup = 0x2f00
usbus0 on uhci0
uhci1: <Intel 82801JI (ICH10) USB controller USB-E> port 0xa880-0xa89f irq 21 at device 26.1 on pci0
uhci1: LegSup = 0x2f00
usbus1 on uhci1
uhci2: <Intel 82801JI (ICH10) USB controller USB-F> port 0xa800-0xa81f irq 19 at device 26.2 on pci0
uhci2: LegSup = 0x2f00
usbus2 on uhci2
ehci0: <Intel 82801JI (ICH10) USB 2.0 controller USB-B> mem 0xfe7ffc00-0xfe7fffff irq 18 at device 26.7 on pci0
usbus3: EHCI version 1.0
usbus3 on ehci0
hdac0: <Intel 82801JI HDA Controller> mem 0xfe7f8000-0xfe7fbfff irq 22 at device 27.0 on pci0
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
atapci0: <JMicron JMB363 UDMA133 controller> port 0xcc00-0xcc07,0xc880-0xc883,0xc800-0xc807,0xc480-0xc483,0xc400-0xc40f mem 0xfe9fe000-0xfe9fffff irq 16 at device 0.0 on pci2
ahci0: <JMicron JMB363 AHCI SATA controller> at channel -1 on atapci0
ahci0: AHCI v1.00 with 2 3Gbps ports, Port Multiplier supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ata2: <ATA channel> at channel 0 on atapci0
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 28.5 on pci0
pci4: <ACPI PCI bus> on pcib4
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port 0xd800-0xd8ff mem 0xfdfff000-0xfdffffff,0xfdfe0000-0xfdfeffff irq 17 at device 0.0 on pci4
re0: Using 1 MSI-X message
re0: Chip rev. 0x3c000000
re0: MAC rev. 0x00400000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re0: Ethernet address: 00:24:21:1e:ed:6b
uhci3: <Intel 82801JI (ICH10) USB controller USB-A> port 0xa480-0xa49f irq 23 at device 29.0 on pci0
uhci3: LegSup = 0x2f00
usbus4 on uhci3
uhci4: <Intel 82801JI (ICH10) USB controller USB-B> port 0xa400-0xa41f irq 19 at device 29.1 on pci0
uhci4: LegSup = 0x2f00
usbus5 on uhci4
uhci5: <Intel 82801JI (ICH10) USB controller USB-C> port 0xa080-0xa09f irq 18 at device 29.2 on pci0
uhci5: LegSup = 0x2f00
usbus6 on uhci5
ehci1: <Intel 82801JI (ICH10) USB 2.0 controller USB-A> mem 0xfe7ff800-0xfe7ffbff irq 23 at device 29.7 on pci0
usbus7: EHCI version 1.0
usbus7 on ehci1
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci5: <ACPI PCI bus> on pcib5
re1: <RealTek 8169/8169S/8169SB(L)/8110S/8110SB(L) Gigabit Ethernet> port 0xe800-0xe8ff mem 0xfebffc00-0xfebffcff irq 16 at device 0.0 on pci5
re1: Chip rev. 0x04000000
re1: MAC rev. 0x00000000
miibus1: <MII bus> on re1
rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus1
rgephy1: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re1: Ethernet address: 00:22:3f:f0:19:85
atapci1: <SiI 3114 SATA150 controller> port 0xec00-0xec07,0xe480-0xe483,0xe400-0xe407,0xe080-0xe083,0xe000-0xe00f mem 0xfebff800-0xfebffbff irq 22 at device 3.0 on pci5
ata3: <ATA channel> at channel 0 on atapci1
ata4: <ATA channel> at channel 1 on atapci1
ata5: <ATA channel> at channel 2 on atapci1
ata6: <ATA channel> at channel 3 on atapci1
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
ahci1: <Intel ICH10 AHCI SATA controller> port 0xa000-0xa007,0x9c00-0x9c03,0x9880-0x9887,0x9800-0x9803,0x9480-0x949f mem 0xfe7ff000-0xfe7ff7ff irq 19 at device 31.2 on pci0
ahci1: AHCI v1.20 with 6 3Gbps ports, Port Multiplier not supported
ahcich2: <AHCI channel> at channel 0 on ahci1
ahcich3: <AHCI channel> at channel 1 on ahci1
ahcich4: <AHCI channel> at channel 2 on ahci1
ahcich5: <AHCI channel> at channel 3 on ahci1
ahcich6: <AHCI channel> at channel 4 on ahci1
ahcich7: <AHCI channel> at channel 5 on ahci1
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ppc0: cannot reserve I/O port range
ctl: CAM Target Layer loaded
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
ZFS filesystem version 5
ZFS storage pool version 28
Timecounters tick every 1.000 msec
ipfw2 (+ipv6) initialized, divert loadable, nat loadable, rule-based forwarding disabled, default to accept, logging disabled
iSCSI boot driver version 0.2.6
hdacc0: <Realtek ALC888 HDA CODEC> at cad 0 on hdac0
hdaa0: <Realtek ALC888 Audio Function Group> at nid 1 on hdacc0
pcm0: <Realtek ALC888 (Rear Analog 7.1/2.0)> at nid 20,22,21,23 and 24,26 on hdaa0
pcm1: <Realtek ALC888 (Front Analog)> at nid 27 and 25 on hdaa0
pcm2: <Realtek ALC888 (Rear Digital)> at nid 30 on hdaa0
md0: Preloaded image </mfsroot> 230686720 bytes at 0xffffffff819a3c58
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <Intel> at usbus6
uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
ugen7.1: <Intel> at usbus7
uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub6: 2 ports with 2 removable, self powered
uhub3: 6 ports with 6 removable, self powered
uhub7: 6 ports with 6 removable, self powered
ugen3.2: <vendor 0x3538> at usbus3
umass0: <vendor 0x3538 product 0x0901, class 0/0, rev 2.00/1.00, addr 2> on usbus3
umass0: SCSI over Bulk-Only; quirks = 0x4100
umass0:14:0:-1: Attached to scbus14
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
da0 at umass-sim0 bus 0 scbus14 target 0 lun 0
da0: <pqi IntelligentStick PMAP> Removable Direct Access SCSI-4 device
da0: 40.000MB/s transfers
da0: 3700MB (7579008 512 byte sectors: 255H 63S/T 471C)
ada0: <WDC WD20EARX-00PASB0 51.0AB51> ATA-8 SATA 3.x device
ada0: 150.000MB/s transfers (SATA 1.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad4
ada1 at ahcich1 bus 0 scbus1 target 0 lun 0
ada1: <WDC WD20EARX-00PASB0 51.0AB51> ATA-8 SATA 3.x device
ada1: 150.000MB/s transfers (SATA 1.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada1: Previously was known as ad6
ada2 at ahcich2 bus 0 scbus7 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC24> ATA-8 SATA 3.x device
ada2: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: Previously was known as ad18
ada3 at ahcich3 bus 0 scbus8 target 0 lun 0
ada3: <ST3000DM001-1CH166 CC24> ATA-8 SATA 3.x device
ada3: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada3: Command Queueing enabled
ada3: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada3: Previously was known as ad20
ada4 at ahcich4 bus 0 scbus9 target 0 lun 0
ada4: <ST3000DM001-1CH166 CC24> ATA-8 SATA 3.x device
ada4: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada4: Command Queueing enabled
ada4: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada4: Previously was known as ad22
ada5 at ahcich5 bus 0 scbus10 target 0 lun 0
ada5: <WDC WD20EARX-00PASB0 51.0AB51> ATA-8 SATA 3.x device
ada5: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada5: Command Queueing enabled
ada5: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada5: Previously was known as ad24
ada6 at ahcich6 bus 0 scbus11 target 0 lun 0
ada6: <ST3000DM001-1CH166 CC24> ATA-8 SATA 3.x device
ada6: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada6: Command Queueing enabled
ada6: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada6: Previously was known as ad26
ada7 at ahcich7 bus 0 scbus12 target 0 lun 0
ada7: <ST3000DM001-1CH166 CC24> ATA-8 SATA 3.x device
ada7: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada7: Command Queueing enabled
ada7: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada7: Previously was known as ad28
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 10964924 Hz quality 1000
GEOM: da0: geometry does not match label (16h,63s != 255h,63s).
GEOM: da0: media size does not match label.
Trying to mount root from ufs:/dev/md0 []...
Loading configuration files.
Booting platform: embedded
Looking for configuration file: ada7 ada6 ada5 ada4 ada3 ada2 ada1 ada0 da0
Found configuration on device=/dev/da0a fstype=ufs.
Updating rc.conf:.....................................
Generating user database(s).
Starting GEOM devices.
Entropy harvesting: interrupts ethernet point_to_point kickstart.
Starting file system checks:
kern.coredump: 1 -> 0
net.inet.tcp.delayed_ack: 1 -> 0
net.inet.tcp.sendspace: 32768 -> 262144
net.inet.tcp.recvspace: 65536 -> 262144
net.inet.tcp.sendbuf_max: 2097152 -> 4194304
net.inet.tcp.sendbuf_inc: 8192 -> 262144
net.inet.tcp.recvbuf_max: 2097152 -> 4194304
net.inet.tcp.recvbuf_inc: 16384 -> 262144
net.inet.udp.recvspace: 42080 -> 65536
net.inet.udp.maxdgram: 9216 -> 57344
net.local.stream.recvspace: 8192 -> 65536
net.local.stream.sendspace: 8192 -> 65536
kern.ipc.maxsockbuf: 2097152 -> 16777216
kern.ipc.somaxconn: 128 -> 8192
kern.ipc.nmbclusters: 25600 -> 262144
kern.ipc.nmbjumbop: 12800 -> 262144
kern.ipc.nmbjumbo9: 6400 -> 131072
kern.ipc.nmbjumbo16: 3200 -> 65536
kern.maxfilesperproc: 58982 -> 50000
net.inet.icmp.icmplim: 200 -> 300
net.inet.tcp.path_mtu_discovery: 1 -> 0
hw.intr_storm_threshold: 1000 -> 9000
Mounting local file systems:.
Load NOP GEOM class
GEOM_NOP: Device ada2.nop created.
GEOM_NOP: Device ada3.nop created.
GEOM_NOP: Device ada4.nop created.
GEOM_NOP: Device ada6.nop created.
GEOM_NOP: Device ada7.nop created.
Setting hostname: nas.local.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0xc
inet 127.0.0.1 netmask 0xff000000
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether 00:24:21:1e:ed:6b
inet 192.168.0.5 netmask 0xffffff00 broadcast 192.168.0.255
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet autoselect (none)
status: no carrier
Starting devd.
Updating hosts.
Generating host.conf.
Updating resolv.conf.
add net default: gateway 192.168.0.254
Additional routing options:.
Waiting for re0 to have link.
Waiting for 192.168.0.254 to respond to ICMP.
Creating clog files.
Starting syslogd.
Generating .websrv_htpasswd.
Preparing web-based file-management.
Initializing Acoustic/Standby/APM/UDMA on ATA disks: ada0 ada1 ada2 ada3 ada4 ada5 ada6 ada7
Generating message of the day.
Removing stale Samba tdb files: done
Load AIO module
Updating passdb.
Starting nmbd.
Starting smbd.
Configuring syscons: blanktime.
Starting sshd.
Generating local rsyncd cron scripts.
Starting cron.
Starting rsyncd.
Starting mdnsresponder.
Generating .htpasswd.
Starting lighttpd.
Setting hostuuid: 00000000-0000-0000-0000-0024211eed6b.
Setting hostid: 0x867b9c8f.
Starting background file system checks in 60 seconds.
Thu Mar 21 00:46:49 CET 2013
Stopping lighttpd.
Waiting for PIDS: 2610.
Stopping rsyncd.
Waiting for PIDS: 2529.
Stopping cron.
Waiting for PIDS: 2482.
Stopping smbd.
Waiting for PIDS: 2363.
Stopping nmbd.
Waiting for PIDS: 2360, 2360.
Stopping devd.
Waiting for PIDS: 1964.
Writing entropy file:.
Stopping GEOM devices.
Terminated
.
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...0 done
All buffers synced.
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.1-RELEASE #0 r246186M: Fri Feb 1 00:21:40 CET 2013
root@dev.nas4free.org:/usr/obj/nas4free/usr/src/sys/NAS4FREE-amd64 amd64
CPU: Intel(R) Core(TM)2 Duo CPU E7400 @ 2.80GHz (2807.02-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x1067a Family = 6 Model = 17 Stepping = 10
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xc08e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,XSAVE,OSXSAVE>
AMD Features=0x20100800<SYSCALL,NX,LM>
AMD Features2=0x1<LAHF>
TSC: P-state invariant, performance statistics
real memory = 4294967296 (4096 MB)
avail memory = 3849969664 (3671 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <7514MS A7514200>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
cryptosoft0: <software crypto> on motherboard
acpi0: <7514MS A7514200> on motherboard
acpi0: Power Button (fixed)
acpi0: reservation of ffc00000, 300000 (3) failed
acpi0: reservation of fee00000, 1000 (3) failed
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, bff00000 (3) failed
cpu0: <ACPI CPU> on acpi0
ACPI Warning: Incorrect checksum in table [OEMB] - 0x85, should be 0x84 (20110527/tbutils-282)
cpu1: <ACPI CPU> on acpi0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 450
Event timer "HPET1" frequency 14318180 Hz quality 440
Event timer "HPET2" frequency 14318180 Hz quality 440
Event timer "HPET3" frequency 14318180 Hz quality 440
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xb000-0xb0ff mem 0xd0000000-0xdfffffff,0xfe8f0000-0xfe8fffff irq 16 at device 0.0 on pci1
vgapci1: <VGA-compatible display> mem 0xfe8e0000-0xfe8effff at device 0.1 on pci1
uhci0: <Intel 82801JI (ICH10) USB controller USB-D> port 0xac00-0xac1f irq 16 at device 26.0 on pci0
uhci0: LegSup = 0x2f00
usbus0 on uhci0
uhci1: <Intel 82801JI (ICH10) USB controller USB-E> port 0xa880-0xa89f irq 21 at device 26.1 on pci0
uhci1: LegSup = 0x2f00
usbus1 on uhci1
uhci2: <Intel 82801JI (ICH10) USB controller USB-F> port 0xa800-0xa81f irq 19 at device 26.2 on pci0
uhci2: LegSup = 0x2f00
usbus2 on uhci2
ehci0: <Intel 82801JI (ICH10) USB 2.0 controller USB-B> mem 0xfe7ffc00-0xfe7fffff irq 18 at device 26.7 on pci0
usbus3: EHCI version 1.0
usbus3 on ehci0
hdac0: <Intel 82801JI HDA Controller> mem 0xfe7f8000-0xfe7fbfff irq 22 at device 27.0 on pci0
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
atapci0: <JMicron JMB363 UDMA133 controller> port 0xcc00-0xcc07,0xc880-0xc883,0xc800-0xc807,0xc480-0xc483,0xc400-0xc40f mem 0xfe9fe000-0xfe9fffff irq 16 at device 0.0 on pci2
ahci0: <JMicron JMB363 AHCI SATA controller> at channel -1 on atapci0
ahci0: AHCI v1.00 with 2 3Gbps ports, Port Multiplier supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ata2: <ATA channel> at channel 0 on atapci0
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 28.5 on pci0
pci4: <ACPI PCI bus> on pcib4
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port 0xd800-0xd8ff mem 0xfdfff000-0xfdffffff,0xfdfe0000-0xfdfeffff irq 17 at device 0.0 on pci4
re0: Using 1 MSI-X message
re0: Chip rev. 0x3c000000
re0: MAC rev. 0x00400000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re0: Ethernet address: 00:24:21:1e:ed:6b
uhci3: <Intel 82801JI (ICH10) USB controller USB-A> port 0xa480-0xa49f irq 23 at device 29.0 on pci0
uhci3: LegSup = 0x2f00
usbus4 on uhci3
uhci4: <Intel 82801JI (ICH10) USB controller USB-B> port 0xa400-0xa41f irq 19 at device 29.1 on pci0
uhci4: LegSup = 0x2f00
usbus5 on uhci4
uhci5: <Intel 82801JI (ICH10) USB controller USB-C> port 0xa080-0xa09f irq 18 at device 29.2 on pci0
uhci5: LegSup = 0x2f00
usbus6 on uhci5
ehci1: <Intel 82801JI (ICH10) USB 2.0 controller USB-A> mem 0xfe7ff800-0xfe7ffbff irq 23 at device 29.7 on pci0
usbus7: EHCI version 1.0
usbus7 on ehci1
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci5: <ACPI PCI bus> on pcib5
re1: <RealTek 8169/8169S/8169SB(L)/8110S/8110SB(L) Gigabit Ethernet> port 0xe800-0xe8ff mem 0xfebffc00-0xfebffcff irq 16 at device 0.0 on pci5
re1: Chip rev. 0x04000000
re1: MAC rev. 0x00000000
miibus1: <MII bus> on re1
rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus1
rgephy1: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re1: Ethernet address: 00:22:3f:f0:19:85
atapci1: <SiI 3114 SATA150 controller> port 0xec00-0xec07,0xe480-0xe483,0xe400-0xe407,0xe080-0xe083,0xe000-0xe00f mem 0xfebff800-0xfebffbff irq 22 at device 3.0 on pci5
ata3: <ATA channel> at channel 0 on atapci1
ata4: <ATA channel> at channel 1 on atapci1
ata5: <ATA channel> at channel 2 on atapci1
ata6: <ATA channel> at channel 3 on atapci1
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
ahci1: <Intel ICH10 AHCI SATA controller> port 0xa000-0xa007,0x9c00-0x9c03,0x9880-0x9887,0x9800-0x9803,0x9480-0x949f mem 0xfe7ff000-0xfe7ff7ff irq 19 at device 31.2 on pci0
ahci1: AHCI v1.20 with 6 3Gbps ports, Port Multiplier not supported
ahcich2: <AHCI channel> at channel 0 on ahci1
ahcich3: <AHCI channel> at channel 1 on ahci1
ahcich4: <AHCI channel> at channel 2 on ahci1
ahcich5: <AHCI channel> at channel 3 on ahci1
ahcich6: <AHCI channel> at channel 4 on ahci1
ahcich7: <AHCI channel> at channel 5 on ahci1
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <Power Button> on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ppc0: cannot reserve I/O port range
ctl: CAM Target Layer loaded
coretemp0: <CPU On-Die Thermal Sensors> on cpu0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
coretemp1: <CPU On-Die Thermal Sensors> on cpu1
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
ZFS filesystem version 5
ZFS storage pool version 28
Timecounters tick every 1.000 msec
ipfw2 (+ipv6) initialized, divert loadable, nat loadable, rule-based forwarding disabled, default to accept, logging disabled
iSCSI boot driver version 0.2.6
hdacc0: <Realtek ALC888 HDA CODEC> at cad 0 on hdac0
hdaa0: <Realtek ALC888 Audio Function Group> at nid 1 on hdacc0
pcm0: <Realtek ALC888 (Rear Analog 7.1/2.0)> at nid 20,22,21,23 and 24,26 on hdaa0
pcm1: <Realtek ALC888 (Front Analog)> at nid 27 and 25 on hdaa0
pcm2: <Realtek ALC888 (Rear Digital)> at nid 30 on hdaa0
md0: Preloaded image </mfsroot> 230686720 bytes at 0xffffffff819a3c58
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <Intel> at usbus6
uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
ugen7.1: <Intel> at usbus7
uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub6: 2 ports with 2 removable, self powered
uhub3: 6 ports with 6 removable, self powered
uhub7: 6 ports with 6 removable, self powered
ugen3.2: <vendor 0x3538> at usbus3
umass0: <vendor 0x3538 product 0x0901, class 0/0, rev 2.00/1.00, addr 2> on usbus3
umass0: SCSI over Bulk-Only; quirks = 0x4100
umass0:14:0:-1: Attached to scbus14
ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
da0 at umass-sim0 bus 0 scbus14 target 0 lun 0
da0: <pqi IntelligentStick PMAP> Removable Direct Access SCSI-4 device
da0: 40.000MB/s transfers
da0: 3700MB (7579008 512 byte sectors: 255H 63S/T 471C)
ada0: <WDC WD20EARX-00PASB0 51.0AB51> ATA-8 SATA 3.x device
ada0: 150.000MB/s transfers (SATA 1.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada0: Previously was known as ad4
ada1 at ahcich1 bus 0 scbus1 target 0 lun 0
ada1: <WDC WD20EARX-00PASB0 51.0AB51> ATA-8 SATA 3.x device
ada1: 150.000MB/s transfers (SATA 1.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada1: Previously was known as ad6
ada2 at ahcich2 bus 0 scbus7 target 0 lun 0
ada2: <ST3000DM001-1CH166 CC24> ATA-8 SATA 3.x device
ada2: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada2: Command Queueing enabled
ada2: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada2: Previously was known as ad18
ada3 at ahcich3 bus 0 scbus8 target 0 lun 0
ada3: <ST3000DM001-1CH166 CC24> ATA-8 SATA 3.x device
ada3: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada3: Command Queueing enabled
ada3: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada3: Previously was known as ad20
ada4 at ahcich4 bus 0 scbus9 target 0 lun 0
ada4: <ST3000DM001-1CH166 CC24> ATA-8 SATA 3.x device
ada4: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada4: Command Queueing enabled
ada4: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada4: Previously was known as ad22
ada5 at ahcich5 bus 0 scbus10 target 0 lun 0
ada5: <WDC WD20EARX-00PASB0 51.0AB51> ATA-8 SATA 3.x device
ada5: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada5: Command Queueing enabled
ada5: 1907729MB (3907029168 512 byte sectors: 16H 63S/T 16383C)
ada5: Previously was known as ad24
ada6 at ahcich6 bus 0 scbus11 target 0 lun 0
ada6: <ST3000DM001-1CH166 CC24> ATA-8 SATA 3.x device
ada6: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada6: Command Queueing enabled
ada6: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada6: Previously was known as ad26
ada7 at ahcich7 bus 0 scbus12 target 0 lun 0
ada7: <ST3000DM001-1CH166 CC24> ATA-8 SATA 3.x device
ada7: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada7: Command Queueing enabled
ada7: 2861588MB (5860533168 512 byte sectors: 16H 63S/T 16383C)
ada7: Previously was known as ad28
SMP: AP CPU #1 Launched!
Timecounter "TSC-low" frequency 10964920 Hz quality 1000
GEOM: da0: geometry does not match label (16h,63s != 255h,63s).
GEOM: da0: media size does not match label.
Trying to mount root from ufs:/dev/md0 []...
Loading configuration files.
Booting platform: embedded
Looking for configuration file: ada7 ada6 ada5 ada4 ada3 ada2 ada1 ada0 da0
Found configuration on device=/dev/da0a fstype=ufs.
Updating rc.conf:.....................................
Generating user database(s).
Starting GEOM devices.
Entropy harvesting: interrupts ethernet point_to_point kickstart.
Starting file system checks:
kern.coredump: 1 -> 0
net.inet.tcp.delayed_ack: 1 -> 0
net.inet.tcp.sendspace: 32768 -> 262144
net.inet.tcp.recvspace: 65536 -> 262144
net.inet.tcp.sendbuf_max: 2097152 -> 4194304
net.inet.tcp.sendbuf_inc: 8192 -> 262144
net.inet.tcp.recvbuf_max: 2097152 -> 4194304
net.inet.tcp.recvbuf_inc: 16384 -> 262144
net.inet.udp.recvspace: 42080 -> 65536
net.inet.udp.maxdgram: 9216 -> 57344
net.local.stream.recvspace: 8192 -> 65536
net.local.stream.sendspace: 8192 -> 65536
kern.ipc.maxsockbuf: 2097152 -> 16777216
kern.ipc.somaxconn: 128 -> 8192
kern.ipc.nmbclusters: 25600 -> 262144
kern.ipc.nmbjumbop: 12800 -> 262144
kern.ipc.nmbjumbo9: 6400 -> 131072
kern.ipc.nmbjumbo16: 3200 -> 65536
kern.maxfilesperproc: 58982 -> 50000
net.inet.icmp.icmplim: 200 -> 300
net.inet.tcp.path_mtu_discovery: 1 -> 0
hw.intr_storm_threshold: 1000 -> 9000
Mounting local file systems:.
Load NOP GEOM class
GEOM_NOP: Device ada2.nop created.
GEOM_NOP: Device ada3.nop created.
GEOM_NOP: Device ada4.nop created.
GEOM_NOP: Device ada6.nop created.
GEOM_NOP: Device ada7.nop created.
Setting hostname: nas.local.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0xc
inet 127.0.0.1 netmask 0xff000000
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether 00:24:21:1e:ed:6b
inet 192.168.0.5 netmask 0xffffff00 broadcast 192.168.0.255
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: Ethernet autoselect (none)
status: no carrier
Starting devd.
Updating hosts.
Generating host.conf.
Updating resolv.conf.
add net default: gateway 192.168.0.254
Additional routing options:.
Waiting for re0 to have link.
Waiting for 192.168.0.254 to respond to ICMP.
Creating clog files.
Starting syslogd.
Generating .websrv_htpasswd.
Preparing web-based file-management.
Initializing Acoustic/Standby/APM/UDMA on ATA disks: ada0 ada1 ada2 ada3 ada4 ada5 ada6 ada7
Generating message of the day.
Removing stale Samba tdb files: done
Load AIO module
Updating passdb.
Starting nmbd.
Starting smbd.
Configuring syscons: blanktime.
Starting sshd.
Generating local rsyncd cron scripts.
Starting cron.
Starting rsyncd.
Starting mdnsresponder.
Generating .htpasswd.
Starting lighttpd.
Setting hostuuid: 00000000-0000-0000-0000-0024211eed6b.
Setting hostid: 0x867b9c8f.
Starting background file system checks in 60 seconds.
Thu Mar 21 01:45:03 CET 2013
Code: Select all
gnop status
Name Status Components
ada2.nop N/A ada2
ada3.nop N/A ada3
ada4.nop N/A ada4
ada6.nop N/A ada6
ada7.nop N/A ada7
Code: Select all
zdb -l -u /dev/ada4
--------------------------------------------
LABEL 0
--------------------------------------------
failed to unpack label 0
Uberblock[0]
magic = 0000000000bab10c
version = 28
txg = 199744
guid_sum = 6806289962340922720
timestamp = 1363791862 UTC = Wed Mar 20 16:04:22 2013
Uberblock[4]
magic = 0000000000bab10c
version = 28
txg = 199777
guid_sum = 6806289962340922720
timestamp = 1363791905 UTC = Wed Mar 20 16:05:05 2013
Uberblock[8]
magic = 0000000000bab10c
version = 28
txg = 202050
guid_sum = 6806289962340922720
timestamp = 1363803059 UTC = Wed Mar 20 19:10:59 2013
Uberblock[12]
magic = 0000000000bab10c
version = 28
txg = 199715
guid_sum = 6806289962340922720
timestamp = 1363791829 UTC = Wed Mar 20 16:03:49 2013
Uberblock[16]
magic = 0000000000bab10c
version = 28
txg = 202052
guid_sum = 6806289962340922720
timestamp = 1363803069 UTC = Wed Mar 20 19:11:09 2013
Uberblock[20]
magic = 0000000000bab10c
version = 28
txg = 202053
guid_sum = 6806289962340922720
timestamp = 1363803074 UTC = Wed Mar 20 19:11:14 2013
Uberblock[24]
magic = 0000000000bab10c
version = 28
txg = 202054
guid_sum = 6806289962340922720
timestamp = 1363803079 UTC = Wed Mar 20 19:11:19 2013
Uberblock[28]
magic = 0000000000bab10c
version = 28
txg = 202055
guid_sum = 6806289962340922720
timestamp = 1363803085 UTC = Wed Mar 20 19:11:25 2013
Uberblock[32]
magic = 0000000000bab10c
version = 28
txg = 199816
guid_sum = 6806289962340922720
timestamp = 1363791932 UTC = Wed Mar 20 16:05:32 2013
Uberblock[36]
magic = 0000000000bab10c
version = 28
txg = 199753
guid_sum = 6806289962340922720
timestamp = 1363791888 UTC = Wed Mar 20 16:04:48 2013
Uberblock[40]
magic = 0000000000bab10c
version = 28
txg = 199786
guid_sum = 6806289962340922720
timestamp = 1363791911 UTC = Wed Mar 20 16:05:11 2013
Uberblock[44]
magic = 0000000000bab10c
version = 28
txg = 199819
guid_sum = 6806289962340922720
timestamp = 1363791934 UTC = Wed Mar 20 16:05:34 2013
Uberblock[48]
magic = 0000000000bab10c
version = 28
txg = 199756
guid_sum = 6806289962340922720
timestamp = 1363791893 UTC = Wed Mar 20 16:04:53 2013
Uberblock[52]
magic = 0000000000bab10c
version = 28
txg = 205613
guid_sum = 6806289962340922720
timestamp = 1363820871 UTC = Thu Mar 21 00:07:51 2013
Uberblock[56]
magic = 0000000000bab10c
version = 28
txg = 205614
guid_sum = 6806289962340922720
timestamp = 1363820871 UTC = Thu Mar 21 00:07:51 2013
Uberblock[60]
magic = 0000000000bab10c
version = 28
txg = 205615
guid_sum = 6806289962340922720
timestamp = 1363820871 UTC = Thu Mar 21 00:07:51 2013
Uberblock[64]
magic = 0000000000bab10c
version = 28
txg = 205616
guid_sum = 6806289962340922720
timestamp = 1363820872 UTC = Thu Mar 21 00:07:52 2013
Uberblock[68]
magic = 0000000000bab10c
version = 28
txg = 205617
guid_sum = 6806289962340922720
timestamp = 1363820872 UTC = Thu Mar 21 00:07:52 2013
Uberblock[72]
magic = 0000000000bab10c
version = 28
txg = 205618
guid_sum = 6806289962340922720
timestamp = 1363820872 UTC = Thu Mar 21 00:07:52 2013
Uberblock[76]
magic = 0000000000bab10c
version = 28
txg = 199827
guid_sum = 6806289962340922720
timestamp = 1363791954 UTC = Wed Mar 20 16:05:54 2013
Uberblock[80]
magic = 0000000000bab10c
version = 28
txg = 199828
guid_sum = 6806289962340922720
timestamp = 1363791959 UTC = Wed Mar 20 16:05:59 2013
Uberblock[84]
magic = 0000000000bab10c
version = 28
txg = 199829
guid_sum = 6806289962340922720
timestamp = 1363791964 UTC = Wed Mar 20 16:06:04 2013
Uberblock[88]
magic = 0000000000bab10c
version = 28
txg = 199830
guid_sum = 6806289962340922720
timestamp = 1363791969 UTC = Wed Mar 20 16:06:09 2013
Uberblock[92]
magic = 0000000000bab10c
version = 28
txg = 199831
guid_sum = 6806289962340922720
timestamp = 1363791974 UTC = Wed Mar 20 16:06:14 2013
Uberblock[96]
magic = 0000000000bab10c
version = 28
txg = 199832
guid_sum = 6806289962340922720
timestamp = 1363791979 UTC = Wed Mar 20 16:06:19 2013
Uberblock[100]
magic = 0000000000bab10c
version = 28
txg = 199801
guid_sum = 6806289962340922720
timestamp = 1363791921 UTC = Wed Mar 20 16:05:21 2013
Uberblock[104]
magic = 0000000000bab10c
version = 28
txg = 199706
guid_sum = 6806289962340922720
timestamp = 1363791824 UTC = Wed Mar 20 16:03:44 2013
Uberblock[108]
magic = 0000000000bab10c
version = 28
txg = 199835
guid_sum = 6806289962340922720
timestamp = 1363791984 UTC = Wed Mar 20 16:06:24 2013
Uberblock[112]
magic = 0000000000bab10c
version = 28
txg = 199836
guid_sum = 6806289962340922720
timestamp = 1363791989 UTC = Wed Mar 20 16:06:29 2013
Uberblock[116]
magic = 0000000000bab10c
version = 28
txg = 199741
guid_sum = 6806289962340922720
timestamp = 1363791857 UTC = Wed Mar 20 16:04:17 2013
Uberblock[120]
magic = 0000000000bab10c
version = 28
txg = 199774
guid_sum = 6806289962340922720
timestamp = 1363791903 UTC = Wed Mar 20 16:05:03 2013
Uberblock[124]
magic = 0000000000bab10c
version = 28
txg = 199807
guid_sum = 6806289962340922720
timestamp = 1363791925 UTC = Wed Mar 20 16:05:25 2013
--------------------------------------------
LABEL 1
--------------------------------------------
failed to unpack label 1
......
......
LABEL 2
--------------------------------------------
failed to unpack label 2
......
......
