9.2.0.1.943: Errors in Disks Management

[martin_loos]

Hello,

get some Errors in the Disks Management Tab.

New installed 9.2.0.1.943 embedded on new USB flash drive.
After "clear and import disks", some of the Drives (da0 and da4) was not detected...
Reboot again the GUI was blocked, only ssh was working. "top" shows my that smartclr was at 100% load.
I'm waiting for 4 h but nothing happened, smartclr was always at 100% Have killed smartclr and GUI works again.
My ZFS was working at that time.
http://imageshack.com/a/img809/327/ypm1.png


Using my old USB flash drive with 9.1.0.1.847 have no problems, all Drives will be detected
http://imageshack.com/a/img841/8034/op7c.png

Does anyone have a solution for that problem?

In advanced thanks

Martin

My PC:
Intel I3 3225 Proc
16 GB RAM
Areca ARC-1220 Raid-Controller in JBOD
5x Toshiba 3T Drives (4x ZFS + 1x Spare)
2x Wintec 16GB SSD ( 1x ZIL + 1x Spare)

[RedAntz]

Hi martin_loos,

http://imageshack.com/a/img841/8034/op7c.png
This screenshot is not from 9.1.0.1.847 (847 does not have 2 controller columns).

Please check your setup/settings/screenshots and re-post.

[martin_loos]

Upppppssss, muddled the pic's

Sorry for that... Here are the correct ones.

This is before "clear and import" (FW 9.2.0.1.943)
http://imageshack.com/a/img809/327/ypm1.png

After "clear and import" and reboot (FW 9.2.0.1.943)
http://imageshack.com/a/img841/8034/op7c.png

With the old one (FW 9.1.0.1.847)
http://imageshack.com/a/img31/2589/7ckp.png

[RedAntz]

Hi martin_loos,

That is weird. Can you please provide me the <disk></disk> section within your config.xml for further troubleshooting ?

[martin_loos]

Sure Here you are https://dl.dropboxusercontent.com/u/114 ... .1.943.xml

Looks like a problem with the Areca Driver. Wrote the "arcmsr_load = yes" into the loader.conf (over GUI), but it looks like ascmsr.ko didn't load during start up.

[RedAntz]

Can you try this at console :-

Code: Select all

smartctl -a -d areca,0 /dev/arcmsr0

Code: Select all

smartctl -a -d areca,5 /dev/arcmsr0

and also the output for :-

Code: Select all

camcontrol devlist -v

[martin_loos]

Code: Select all

nas4free: ~ # smartctl -a -d areca,0 /dev/arcmsr0                               
smartctl 6.2 2013-07-26 r3841 [FreeBSD 9.2-RELEASE-p3 amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

/dev/arcmsr0: Option -d areca,N/E (N=0) must have 1 <= N <= 128
=======> VALID ARGUMENTS ARE: ata, scsi, sat[,auto][,N][+TYPE], usbcypress[,X], usbjmicron[,p][,x][,N], usbsunplus, 3ware,N, hpt,L/M/N, cciss,N, areca,N/E, atacam, auto, test <=======

Use smartctl -h to get a usage summary

Code: Select all

nas4free: ~ # smartctl -a -d areca,5 /dev/arcmsr0
smartctl 6.2 2013-07-26 r3841 [FreeBSD 9.2-RELEASE-p3 amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     [No Information Found]
Serial Number:    [No Information Found]
Firmware Version: [No Information Found]
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   [No Information Found]
Local Time is:    Fri Feb 14 16:18:29 2014 CET
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 82-83 don't show if SMART supported.
SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 85-87 don't show if SMART is enabled.
A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.

Code: Select all

nas4free: ~ # camcontrol devlist -v
scbus0 on arcmsr0 bus 0:
<TOSHIBA DT01ACA300 R001>          at scbus0 target 0 lun 0 (da0,pass0)
<TOSHIBA DT01ACA300 R001>          at scbus0 target 1 lun 0 (da1,pass1)
<TOSHIBA DT01ACA300 R001>          at scbus0 target 2 lun 0 (da2,pass2)
<TOSHIBA DT01ACA300 R001>          at scbus0 target 3 lun 0 (da3,pass3)
<TOSHIBA DT01ACA300 R001>          at scbus0 target 5 lun 0 (da4,pass4)
<Areca RAID controller R001>       at scbus0 target 16 lun 0 (pass5) 
<>                                  at scbus0 target -1 lun -1 ()
scbus1 on ata2 bus 0:
<Wintec SSD 16GB 02.10104>         at scbus1 target 0 lun 0 (ada0,pass6)
<>                                 at scbus1 target -1 lun -1 ()
scbus2 on ata3 bus 0:
<Wintec SSD 16GB 02.10104>         at scbus2 target 0 lun 0 (ada1,pass7)
<>                                 at scbus2 target -1 lun -1 ()
scbus3 on ata4 bus 0:
<>                                 at scbus3 target -1 lun -1 ()
scbus4 on ata5 bus 0:
<>                                 at scbus4 target -1 lun -1 ()
scbus5 on ctl2cam0 bus 0:
<>                                 at scbus5 target -1 lun -1 ()
scbus6 on umass-sim0 bus 0:
<TDK LoR Trans-It 8.07>            at scbus6 target 0 lun 0 (pass8,da5)
scbus-1 on xpt0 bus 0:
<>                                 at scbus-1 target -1 lun -1 (xpt0)

[RedAntz]

This is interesting.

Sorry to trouble you again as I do not have Areca cards for testing. Would you mind to post the following as well ?

Code: Select all

smartctl -a -d test /dev/da4

and

Code: Select all

smartctl -a /dev/da4

and

Code: Select all

dmesg

[martin_loos]

Nevermind

Here a the new results:

Code: Select all

nas4free: ~ # smartctl -a -d test /dev/da4
smartctl 6.2 2013-07-26 r3841 [FreeBSD 9.2-RELEASE-p3 amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

/dev/da4: Device of type 'scsi' [SCSI] detected
/dev/da4: Device of type 'scsi' [SCSI] opened

Code: Select all

nas4free: ~ # smartctl -a /dev/da4
smartctl 6.2 2013-07-26 r3841 [FreeBSD 9.2-RELEASE-p3 amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               TOSHIBA
Product:              DT01ACA300
Revision:             R001
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
Rotation Rate:        10000 rpm
Logical Unit id:      0x0004d927fffff850
Serial number:        533SMYLGS
Device type:          disk
Transport protocol:   Fibre channel (FCP-2)
Local Time is:        Sat Feb 15 15:55:34 2014 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Disabled or Not Supported

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     30 C
Drive Trip Temperature:        25 C

Manufactured in week 30 of year 2002
Specified cycle count over device lifetime:  4278190080
Accumulated start-stop cycles:  256
Elements in grown defect list: 0

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0          0          0.000           0
write:         0        0         0         0          0          0.000           0

Non-medium error count:        0

Device does not support Self Test logging

Code: Select all

dmesg see attached link

https://dl.dropboxusercontent.com/u/114 ... sg_9.2.txt

[RedAntz]

Hi martin_loos,

Would you mind to PM me your email address so that I can send you the patch to test when it's ready ?

[RedAntz]

Sent you the patch for testing.

Can you please send me the following output as well :-

Code: Select all

smartctl -d test /dev/da5

and

Code: Select all

smartctl -i /dev/da5

[RedAntz]

Hi martin_loos,

Thanks for your help in troubleshooting and testing out the patch !

The fix is rolled out.