I've made quite a mess of things and can really use some help...
I'm running Nas4free 9.2.0.1 (943) embedded on a Dell core2duo system and a couple days ago moved the drives to a Atom d525 system.
My setup is a 1TB Raid 1 "Library", a 250GB Raid 1 "User", and a 1TB single drive I was using as temporary storage because the 1TB raid only has about 30gb free.
I moved the CF card with the Nas4free embedded image to the Atom d525 replacement system, booted up the new system without the drives, just to make sure everything was okay with the new hardware. Then I moved the drives over, cleared the config and imported the Raid disks and everything worked same as before.
The Library 1TB Raid was showing as degraded today, but was still accessable and I could see all the folders and files.
I've been meaning to upgrade the 1TB Library raid to 2TB, the 250GB User Raid was empty and the 1TB single drive had some data on it that is stored elsewhere so it's okay to wipe that drive.
My plan was to ditch the 250GB raid and the 1TB single drive so I went to delete the mount point of the 250GB User Raid and when I deleted it, it said that I had deleted the Library mount point! But the Library mount point was and still is listed. The only option was to save the changes and I knew I didn't want to do that so I did a quick google search and it seemed like the changes would not be written if I did a shutdown without clicking the save button, so that's what I did, shutdown with out saving the changes.
So I removed the 250GB "User" raid drives and the 1TB single drive and left the 1TB Raid 1 "Library".
After removing the above, I booted it up, cleared the config and re-imported discs and was planning to copy the data from the degraded Library raid to the 1TB drive I pulled (now in another computer), but I can no longer access the Library Raid 1.
I think that about sums it up. I hope it makes sense, I've been in a bit of a panic. Here's a link to some screenshots if they help to shed any light on the mess I made.
Link to screenshots
Can I rebuild the raid with the spare 1TB drive I have? I'm not sure how to proceed, is the data lost? I'm hoping to be able to either rebuild the raid with the spare 1TB drive I have or restore the mount point and copy the data off the raid to the spare 1TB drive.
If I can do either of those, then I'll pick up two new 2TB drives and make a new raid to store the data.
This is the old XigmaNAS forum in read only mode,
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
I can really use some help
-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: I can really use some help
post the output from Diagnostics|Log
what happened to the other drive from the 1tb array?
what happened to the other drive from the 1tb array?
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: I can really use some help
as a last resort you could also try UFS Explorer on a Windows computer to see if it can identify any files on the drive.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
-
robby6732
- NewUser
- Posts: 5
- Joined: 16 Sep 2014 02:15
- Status: Offline
Re: I can really use some help
b0ssman,
I'm not sure what you mean about what happened to the other 1TB drive in the array. I've got three 1TB drives, 2 Western Digitals as Raid 1 named Library and the third 1TB drive is a Seagate that I was using as non-raid storage. In the screen shots I posted and also in this attached diagnostic log the only drives in the Nas4free system are the two WD 1TB drives that make up the Library raid.
I connected each WD 1TB drive in a Windows 7 system one at a time and I can view all the files with the UFS Explorer software, both Standard edition as well as the Raid edition see all the files. I ran the UFS Explorer Basic Test on the WD drive with the serial number ending in 222 and it passed with no bad information.
Here's the diagnostic log text. Thanks for your help and any more suggestions you may have.
I'm not sure what you mean about what happened to the other 1TB drive in the array. I've got three 1TB drives, 2 Western Digitals as Raid 1 named Library and the third 1TB drive is a Seagate that I was using as non-raid storage. In the screen shots I posted and also in this attached diagnostic log the only drives in the Nas4free system are the two WD 1TB drives that make up the Library raid.
I connected each WD 1TB drive in a Windows 7 system one at a time and I can view all the files with the UFS Explorer software, both Standard edition as well as the Raid edition see all the files. I ran the UFS Explorer Basic Test on the WD drive with the serial number ending in 222 and it passed with no bad information.
Here's the diagnostic log text. Thanks for your help and any more suggestions you may have.
Code: Select all
Sep 16 03:42:30 mammoth lighttpd[2375]: (connections.c.137) (warning) close: 9 Connection reset by peer
Sep 16 03:41:31 mammoth nmbd[2173]: *****
Sep 16 03:41:31 mammoth nmbd[2173]:
Sep 16 03:41:31 mammoth nmbd[2173]: Samba name server MAMMOTH is now a local master browser for workgroup WORKGROUP on subnet 192.168.1.80
Sep 16 03:41:31 mammoth nmbd[2173]:
Sep 16 03:41:31 mammoth nmbd[2173]: *****
Sep 16 03:41:31 mammoth nmbd[2173]: [2014/09/16 03:41:31.721932, 0] nmbd/nmbd_become_lmb.c:397(become_local_master_stage2)
Sep 16 03:41:15 mammoth nmbd[2173]: *****
Sep 16 03:41:15 mammoth nmbd[2173]:
Sep 16 03:41:15 mammoth nmbd[2173]: Samba server MAMMOTH is now a domain master browser for workgroup WORKGROUP on subnet 192.168.1.80
Sep 16 03:41:15 mammoth nmbd[2173]:
Sep 16 03:41:15 mammoth nmbd[2173]: *****
Sep 16 03:41:15 mammoth nmbd[2173]: [2014/09/16 03:41:15.138012, 0] nmbd/nmbd_become_dmb.c:112(become_domain_master_stage2)
Sep 16 03:41:08 mammoth login: login on ttyu0 as root
Sep 16 03:41:08 mammoth login: login on ttyv0 as root
Sep 16 03:41:07 mammoth lighttpd[2375]: (log.c.166) server started
Sep 16 03:41:07 mammoth nmbd[2173]: become_domain_master_browser_bcast: querying subnet 192.168.1.80 for domain master browser on workgroup WORKGROUP
Sep 16 03:41:07 mammoth nmbd[2173]: [2014/09/16 03:41:07.014885, 0] nmbd/nmbd_become_dmb.c:307(become_domain_master_browser_bcast)
Sep 16 03:41:07 mammoth nmbd[2173]: Attempting to become domain master browser on workgroup WORKGROUP on subnet 192.168.1.80
Sep 16 03:41:07 mammoth nmbd[2173]: become_domain_master_browser_bcast:
Sep 16 03:41:07 mammoth nmbd[2173]: [2014/09/16 03:41:07.014439, 0] nmbd/nmbd_become_dmb.c:294(become_domain_master_browser_bcast)
Sep 16 03:41:06 mammoth kernel: ada1
Sep 16 03:41:05 mammoth root: /etc/rc: WARNING: failed to start tftpd
Sep 16 03:41:05 mammoth in.tftpd[1961]: /mnt/Library/TFTP/: No such file or directory
Sep 16 03:41:05 mammoth kernel: GEOM_MIRROR: Cannot add disk ada0 to Library (error=22).
Sep 16 03:41:05 mammoth kernel: GEOM_MIRROR: Component ada0 (device Library) broken, skipping.
Sep 16 03:41:05 mammoth kernel: Failed to start journal: 5
Sep 16 03:41:05 mammoth kernel: Failed to find journal. Use tunefs to create one
Sep 16 03:41:05 mammoth kernel: g_vfs_done():ufsid/50e48f97aedd2463[READ(offset=163840, length=32768)]error = 5
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Error 5, Retries exhausted
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 2f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 62 01 00 40 00 00 00 00 40 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 2f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 62 01 00 40 00 00 00 00 40 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 2f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 62 01 00 40 00 00 00 00 40 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 2f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 62 01 00 40 00 00 00 00 40 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 2f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 62 01 00 40 00 00 00 00 40 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Error 5, Retries exhausted
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 af 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 22 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 af 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 22 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 af 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 22 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 af 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 22 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 af 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 22 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Error 5, Retries exhausted
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 af 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 22 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 af 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 22 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 af 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 22 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 af 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 22 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 af 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 22 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Error 5, Retries exhausted
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 8f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 00 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 8f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 00 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 8f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 00 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 8f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 00 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 8f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 00 01 00 40 00 00 00 00 00 00
Sep 16 03:41:05 mammoth kernel: GEOM_MIRROR: Cannot add disk ada0 to Library (error=22).
Sep 16 03:41:05 mammoth kernel: GEOM_MIRROR: Component ada0 (device Library) broken, skipping.
Sep 16 03:41:05 mammoth kernel: Failed to start journal: 5
Sep 16 03:41:05 mammoth kernel: Failed to find journal. Use tunefs to create one
Sep 16 03:41:05 mammoth kernel: g_vfs_done():ufsid/50e48f97aedd2463[READ(offset=163840, length=32768)]error = 5
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Error 5, Retries exhausted
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 2f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 62 01 00 40 00 00 00 00 40 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 2f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 62 01 00 40 00 00 00 00 40 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 2f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 62 01 00 40 00 00 00 00 40 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 2f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 62 01 00 40 00 00 00 00 40 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): Retrying command
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): RES: 51 40 69 01 00 00 00 00 00 2f 00
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): ATA status: 51 (DRDY SERV ERR), error: 40 (UNC )
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): CAM status: ATA Status Error
Sep 16 03:41:05 mammoth kernel: (ada0:ata2:0:0:0): READ_DMA. ACB: c8 00 62 01 00 40 00 00 00 00 40 00
Sep 16 03:41:05 mammoth kernel: GEOM_MIRROR: Cannot add disk ada0 to Library (error=22).
Sep 16 03:41:05 mammoth kernel: GEOM_MIRROR: Component ada0 (device Library) broken, skipping.
Sep 16 03:41:05 mammoth kernel: GEOM: ada0: the secondary GPT header is not in the last LBA.
Sep 16 03:41:05 mammoth kernel: GEOM_MIRROR: Device mirror/Library launched (1/2).
Sep 16 03:41:05 mammoth kernel:
Sep 16 03:41:05 mammoth kernel: GEOM_MIRROR: cancelling unmapped because of ada1
Sep 16 03:41:05 mammoth kernel: GEOM_MIRROR: Component ada0 (device Library) broken, skipping.
Sep 16 03:41:05 mammoth kernel: Trying to mount root from ufs:/dev/md0 []...
Sep 16 03:41:05 mammoth kernel: GEOM: ada1: the secondary GPT header is not in the last LBA.
Sep 16 03:41:05 mammoth kernel: GEOM: ada0: the secondary GPT header is not in the last LBA.
Sep 16 03:41:05 mammoth kernel: uhid0: <CPS UPS OR700, class 0/0, rev 1.10/2.00, addr 2> on usbus4
Sep 16 03:41:05 mammoth kernel: ugen4.2: <CPS> at usbus4
Sep 16 03:41:05 mammoth kernel: Timecounter "TSC" frequency 1800039717 Hz quality 1000
Sep 16 03:41:05 mammoth kernel: SMP: AP CPU #2 Launched!
Sep 16 03:41:05 mammoth kernel: SMP: AP CPU #3 Launched!
Sep 16 03:41:05 mammoth kernel: SMP: AP CPU #1 Launched!
Sep 16 03:41:05 mammoth kernel: ada1: Previously was known as ad6
Sep 16 03:41:05 mammoth kernel: ada1: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
Sep 16 03:41:05 mammoth kernel: ada1: 300.000MB/s transfers (SATA 2.x, UDMA5, PIO 8192bytes)
Sep 16 03:41:05 mammoth kernel: ada1: <WDC WD10EADS-00P8B0 01.00A01> ATA-8 SATA 2.x device
Sep 16 03:41:05 mammoth kernel: ada1 at ata3 bus 0 scbus1 target 0 lun 0
Sep 16 03:41:05 mammoth kernel: ada0: Previously was known as ad4
Sep 16 03:41:05 mammoth kernel: da4: quirks=0x2<NO_6_BYTE>
Sep 16 03:41:05 mammoth kernel: da4: Attempt to query device size failed: NOT READY, Medium not present
Sep 16 03:41:05 mammoth kernel: da4: 40.000MB/s transfers
Sep 16 03:41:05 mammoth kernel: da4: <Generic SD/MMC/MS/MSPRO 0.00> Removable Direct Access SCSI-2 device
Sep 16 03:41:05 mammoth kernel: da4 at umass-sim0 bus 0 scbus5 target 0 lun 4
Sep 16 03:41:05 mammoth kernel: ada0: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
Sep 16 03:41:05 mammoth kernel: ada0: 300.000MB/s transfers (SATA 2.x, UDMA5, PIO 8192bytes)
Sep 16 03:41:05 mammoth kernel: da3: quirks=0x2<NO_6_BYTE>
Sep 16 03:41:05 mammoth kernel: da3: Attempt to query device size failed: NOT READY, Medium not present
Sep 16 03:41:05 mammoth kernel: da3: 40.000MB/s transfers
Sep 16 03:41:05 mammoth kernel: da3: <Generic MS/MS-Pro/HG 0.00> Removable Direct Access SCSI-2 device
Sep 16 03:41:05 mammoth kernel: da3 at umass-sim0 bus 0 scbus5 target 0 lun 3
Sep 16 03:41:05 mammoth kernel: ada0: <WDC WD10EADS-00P8B0 01.00A01> ATA-8 SATA 2.x device
Sep 16 03:41:05 mammoth kernel: ada0 at ata2 bus 0 scbus0 target 0 lun 0
Sep 16 03:41:05 mammoth kernel: da2: quirks=0x2<NO_6_BYTE>
Sep 16 03:41:05 mammoth kernel: da2: Attempt to query device size failed: NOT READY, Medium not present
Sep 16 03:41:05 mammoth kernel: da2: 40.000MB/s transfers
Sep 16 03:41:05 mammoth kernel: da2: <Generic SDXC/MMC 0.00> Removable Direct Access SCSI-2 device
Sep 16 03:41:05 mammoth kernel: da2 at umass-sim0 bus 0 scbus5 target 0 lun 2
Sep 16 03:41:05 mammoth kernel: da1: quirks=0x2<NO_6_BYTE>
Sep 16 03:41:05 mammoth kernel: da1: Attempt to query device size failed: NOT READY, Medium not present
Sep 16 03:41:05 mammoth kernel: da1: 40.000MB/s transfers
Sep 16 03:41:05 mammoth kernel: da1: <Generic SM/xD-Picture 0.00> Removable Direct Access SCSI-2 device
Sep 16 03:41:05 mammoth kernel: da1 at umass-sim0 bus 0 scbus5 target 0 lun 1
Sep 16 03:41:05 mammoth kernel: da0: quirks=0x2<NO_6_BYTE>
Sep 16 03:41:05 mammoth kernel: da0: 3815MB (7813120 512 byte sectors: 255H 63S/T 486C)
Sep 16 03:41:05 mammoth kernel: da0: 40.000MB/s transfers
Sep 16 03:41:05 mammoth kernel: da0: <Generic Compact Flash 0.00> Removable Direct Access SCSI-2 device
Sep 16 03:41:05 mammoth kernel: da0 at umass-sim0 bus 0 scbus5 target 0 lun 0
Sep 16 03:41:05 mammoth kernel: umass0:5:0:-1: Attached to scbus5
Sep 16 03:41:05 mammoth kernel: umass0: SCSI over Bulk-Only; quirks = 0x4000
Sep 16 03:41:05 mammoth kernel: umass0: <Generic Mass Storage Device, class 0/0, rev 2.00/1.00, addr 2> on usbus3
Sep 16 03:41:05 mammoth kernel: ugen3.2: <Generic> at usbus3
Sep 16 03:41:05 mammoth kernel: uhub7: 6 ports with 6 removable, self powered
Sep 16 03:41:05 mammoth kernel: uhub3: 6 ports with 6 removable, self powered
Sep 16 03:41:05 mammoth kernel: uhub6: 2 ports with 2 removable, self powered
Sep 16 03:41:05 mammoth kernel: uhub5: 2 ports with 2 removable, self powered
Sep 16 03:41:05 mammoth kernel: uhub4: 2 ports with 2 removable, self powered
Sep 16 03:41:05 mammoth kernel: uhub2: 2 ports with 2 removable, self powered
Sep 16 03:41:05 mammoth kernel: uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
Sep 16 03:41:05 mammoth kernel: ugen7.1: <Intel> at usbus7
Sep 16 03:41:05 mammoth kernel: uhub1: 2 ports with 2 removable, self powered
Sep 16 03:41:05 mammoth kernel: uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
Sep 16 03:41:05 mammoth kernel: ugen6.1: <Intel> at usbus6
Sep 16 03:41:05 mammoth kernel: usbus7: 480Mbps High Speed USB v2.0
Sep 16 03:41:05 mammoth kernel: usbus6: 12Mbps Full Speed USB v1.0
Sep 16 03:41:05 mammoth kernel: uhub0: 2 ports with 2 removable, self powered
Sep 16 03:41:05 mammoth kernel: uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
Sep 16 03:41:05 mammoth kernel: ugen5.1: <Intel> at usbus5
Sep 16 03:41:05 mammoth kernel: uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
Sep 16 03:41:05 mammoth kernel: ugen4.1: <Intel> at usbus4
Sep 16 03:41:05 mammoth kernel: usbus5: 12Mbps Full Speed USB v1.0
Sep 16 03:41:05 mammoth kernel: usbus4: 12Mbps Full Speed USB v1.0
Sep 16 03:41:05 mammoth kernel: uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
Sep 16 03:41:05 mammoth kernel: ugen3.1: <Intel> at usbus3
Sep 16 03:41:05 mammoth kernel: uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
Sep 16 03:41:05 mammoth kernel: ugen2.1: <Intel> at usbus2
Sep 16 03:41:05 mammoth kernel: usbus3: 480Mbps High Speed USB v2.0
Sep 16 03:41:05 mammoth kernel: usbus2: 12Mbps Full Speed USB v1.0
Sep 16 03:41:05 mammoth kernel: uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
Sep 16 03:41:05 mammoth kernel: ugen1.1: <Intel> at usbus1
Sep 16 03:41:05 mammoth kernel: uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
Sep 16 03:41:05 mammoth kernel: ugen0.1: <Intel> at usbus0
Sep 16 03:41:05 mammoth kernel: usbus1: 12Mbps Full Speed USB v1.0
Sep 16 03:41:05 mammoth kernel: usbus0: 12Mbps Full Speed USB v1.0
Sep 16 03:41:05 mammoth kernel: md0: Preloaded image </mfsroot> 250609664 bytes at 0xffffffff81d894d0
Sep 16 03:41:05 mammoth kernel: iSCSI boot driver version 0.2.6
Sep 16 03:41:05 mammoth kernel: ipfw2 (+ipv6) initialized, divert loadable, nat loadable, default to accept, logging disabled
Sep 16 03:41:05 mammoth kernel: Timecounters tick every 1.000 msec
Sep 16 03:41:05 mammoth kernel: ZFS storage pool version: features support (5000)
Sep 16 03:41:05 mammoth kernel: ZFS filesystem version: 5
Sep 16 03:41:05 mammoth kernel: to enable, add "vfs.zfs.prefetch_disable=0" to /boot/loader.conf.
Sep 16 03:41:05 mammoth kernel: ZFS NOTICE: Prefetch is disabled by default if less than 4GB of RAM is present;
Sep 16 03:41:05 mammoth kernel: p4tcc3: <CPU Frequency Thermal Control> on cpu3
Sep 16 03:41:05 mammoth kernel: coretemp3: <CPU On-Die Thermal Sensors> on cpu3
Sep 16 03:41:05 mammoth kernel: p4tcc2: <CPU Frequency Thermal Control> on cpu2
Sep 16 03:41:05 mammoth kernel: coretemp2: <CPU On-Die Thermal Sensors> on cpu2
Sep 16 03:41:05 mammoth kernel: p4tcc1: <CPU Frequency Thermal Control> on cpu1
Sep 16 03:41:05 mammoth kernel: coretemp1: <CPU On-Die Thermal Sensors> on cpu1
Sep 16 03:41:05 mammoth kernel: p4tcc0: <CPU Frequency Thermal Control> on cpu0
Sep 16 03:41:05 mammoth kernel: coretemp0: <CPU On-Die Thermal Sensors> on cpu0
Sep 16 03:41:05 mammoth kernel: ctl: CAM Target Layer loaded
Sep 16 03:41:05 mammoth kernel: ppc0: cannot reserve I/O port range
Sep 16 03:41:05 mammoth kernel: vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Sep 16 03:41:05 mammoth kernel: sc0: VGA <16 virtual consoles, flags=0x300>
Sep 16 03:41:05 mammoth kernel: sc0: <System console> at flags 0x100 on isa0
Sep 16 03:41:05 mammoth kernel: psm0: model IntelliMouse Explorer, device ID 4
Sep 16 03:41:05 mammoth kernel: psm0: [GIANT-LOCKED]
Sep 16 03:41:05 mammoth kernel: psm0: <PS/2 Mouse> irq 12 on atkbdc0
Sep 16 03:41:05 mammoth kernel: atkbd0: [GIANT-LOCKED]
Sep 16 03:41:05 mammoth kernel: kbd0 at atkbd0
Sep 16 03:41:05 mammoth kernel: atkbd0: <AT Keyboard> irq 1 on atkbdc0
Sep 16 03:41:05 mammoth kernel: atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
Sep 16 03:41:05 mammoth kernel: uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
Sep 16 03:41:05 mammoth kernel: uart0: console (9600,n,8,1)
Sep 16 03:41:05 mammoth kernel: uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
Sep 16 03:41:05 mammoth kernel: acpi_button0: <Power Button> on acpi0
Sep 16 03:41:05 mammoth kernel: ata5: <ATA channel> at channel 1 on atapci1
Sep 16 03:41:05 mammoth kernel: ata4: <ATA channel> at channel 0 on atapci1
Sep 16 03:41:05 mammoth kernel: atapci1: <Intel ICH9 SATA300 controller> port 0xac00-0xac07,0xa880-0xa883,0xa800-0xa807,0xa480-0xa483,0xa400-0xa40f,0xa080-0xa08f irq 19 at device 31.5 on pci0
Sep 16 03:41:05 mammoth kernel: pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
Sep 16 03:41:05 mammoth kernel: ata3: <ATA channel> at channel 1 on atapci0
Sep 16 03:41:05 mammoth kernel: ata2: <ATA channel> at channel 0 on atapci0
Sep 16 03:41:05 mammoth kernel: atapci0: <Intel ICH9 SATA300 controller> port 0xbc00-0xbc07,0xb880-0xb883,0xb800-0xb807,0xb480-0xb483,0xb400-0xb40f,0xb080-0xb08f irq 19 at device 31.2 on pci0
Sep 16 03:41:05 mammoth kernel: isa0: <ISA bus> on isab0
Sep 16 03:41:05 mammoth kernel: isab0: <PCI-ISA bridge> at device 31.0 on pci0
Sep 16 03:41:05 mammoth kernel: pci4: <ACPI PCI bus> on pcib4
Sep 16 03:41:05 mammoth kernel: pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0
Sep 16 03:41:05 mammoth kernel: usbus7 on ehci1
Sep 16 03:41:05 mammoth kernel: usbus7: EHCI version 1.0
Sep 16 03:41:05 mammoth kernel: ehci1: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xfe877800-0xfe877bff irq 23 at device 29.7 on pci0
Sep 16 03:41:05 mammoth kernel: usbus6 on uhci5
Sep 16 03:41:05 mammoth kernel: uhci5: LegSup = 0x2f00
Sep 16 03:41:05 mammoth kernel: uhci5: <Intel 82801I (ICH9) USB controller> port 0xc000-0xc01f irq 18 at device 29.2 on pci0
Sep 16 03:41:05 mammoth kernel: usbus5 on uhci4
Sep 16 03:41:05 mammoth kernel: uhci4: LegSup = 0x2f00
Sep 16 03:41:05 mammoth kernel: uhci4: <Intel 82801I (ICH9) USB controller> port 0xc080-0xc09f irq 19 at device 29.1 on pci0
Sep 16 03:41:05 mammoth kernel: usbus4 on uhci3
Sep 16 03:41:05 mammoth kernel: uhci3: LegSup = 0x2f00
Sep 16 03:41:05 mammoth kernel: uhci3: <Intel 82801I (ICH9) USB controller> port 0xc400-0xc41f irq 23 at device 29.0 on pci0
Sep 16 03:41:05 mammoth kernel: em1: Ethernet address: 00:25:90:31:c5:df
Sep 16 03:41:05 mammoth kernel: em1: Using MSIX interrupts with 3 vectors
Sep 16 03:41:05 mammoth kernel: em1: <Intel(R) PRO/1000 Network Connection 7.3.8> port 0xec00-0xec1f mem 0xfebe0000-0xfebfffff,0xfebdc000-0xfebdffff irq 17 at device 0.0 on pci3
Sep 16 03:41:05 mammoth kernel: pci3: <ACPI PCI bus> on pcib3
Sep 16 03:41:05 mammoth kernel: pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.5 on pci0
Sep 16 03:41:05 mammoth kernel: em0: Ethernet address: 00:25:90:31:c5:de
Sep 16 03:41:05 mammoth kernel: em0: Using MSIX interrupts with 3 vectors
Sep 16 03:41:05 mammoth kernel: em0: <Intel(R) PRO/1000 Network Connection 7.3.8> port 0xdc00-0xdc1f mem 0xfeae0000-0xfeafffff,0xfeadc000-0xfeadffff irq 16 at device 0.0 on pci2
Sep 16 03:41:05 mammoth kernel: pci2: <ACPI PCI bus> on pcib2
Sep 16 03:41:05 mammoth kernel: pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.4 on pci0
Sep 16 03:41:05 mammoth kernel: pci1: <ACPI PCI bus> on pcib1
Sep 16 03:41:05 mammoth kernel: pcib1: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
Sep 16 03:41:05 mammoth kernel: usbus3 on ehci0
Sep 16 03:41:05 mammoth kernel: usbus3: EHCI version 1.0
Sep 16 03:41:05 mammoth kernel: ehci0: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xfe877c00-0xfe877fff irq 18 at device 26.7 on pci0
Sep 16 03:41:05 mammoth kernel: usbus2 on uhci2
Sep 16 03:41:05 mammoth kernel: uhci2: LegSup = 0x2f00
Sep 16 03:41:05 mammoth kernel: uhci2: <Intel 82801I (ICH9) USB controller> port 0xc480-0xc49f irq 19 at device 26.2 on pci0
Sep 16 03:41:05 mammoth kernel: usbus1 on uhci1
Sep 16 03:41:05 mammoth kernel: uhci1: LegSup = 0x2f00
Sep 16 03:41:05 mammoth kernel: uhci1: <Intel 82801I (ICH9) USB controller> port 0xc800-0xc81f irq 21 at device 26.1 on pci0
Sep 16 03:41:05 mammoth kernel: usbus0 on uhci0
Sep 16 03:41:05 mammoth kernel: uhci0: LegSup = 0x2f00
Sep 16 03:41:05 mammoth kernel: uhci0: <Intel 82801I (ICH9) USB controller> port 0xc880-0xc89f irq 16 at device 26.0 on pci0
Sep 16 03:41:05 mammoth kernel: vgapci1: <VGA-compatible display> mem 0xfe780000-0xfe7fffff at device 2.1 on pci0
Sep 16 03:41:05 mammoth kernel: agp0: aperture size is 256M, detected 8188k stolen memory
Sep 16 03:41:05 mammoth kernel: agp0: <Intel Pineview SVGA controller> on vgapci0
Sep 16 03:41:05 mammoth kernel: vgapci0: <VGA-compatible display> port 0xcc00-0xcc07 mem 0xfe880000-0xfe8fffff,0xd0000000-0xdfffffff,0xfe900000-0xfe9fffff irq 16 at device 2.0 on pci0
Sep 16 03:41:05 mammoth kernel: pci0: <ACPI PCI bus> on pcib0
Sep 16 03:41:05 mammoth kernel: pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
Sep 16 03:41:05 mammoth kernel: acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
Sep 16 03:41:05 mammoth kernel: Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
Sep 16 03:41:05 mammoth kernel: Event timer "HPET3" frequency 14318180 Hz quality 440
Sep 16 03:41:05 mammoth kernel: Event timer "HPET2" frequency 14318180 Hz quality 440
Sep 16 03:41:05 mammoth kernel: Event timer "HPET1" frequency 14318180 Hz quality 440
Sep 16 03:41:05 mammoth kernel: Event timer "HPET" frequency 14318180 Hz quality 450
Sep 16 03:41:05 mammoth kernel: Timecounter "HPET" frequency 14318180 Hz quality 950
Sep 16 03:41:05 mammoth kernel: hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Sep 16 03:41:05 mammoth kernel: Event timer "RTC" frequency 32768 Hz quality 0
Sep 16 03:41:05 mammoth kernel: atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
Sep 16 03:41:05 mammoth kernel: Event timer "i8254" frequency 1193182 Hz quality 100
Sep 16 03:41:05 mammoth kernel: Timecounter "i8254" frequency 1193182 Hz quality 0
Sep 16 03:41:05 mammoth kernel: attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Sep 16 03:41:05 mammoth kernel: cpu3: <ACPI CPU> on acpi0
Sep 16 03:41:05 mammoth kernel: cpu2: <ACPI CPU> on acpi0
Sep 16 03:41:05 mammoth kernel: cpu1: <ACPI CPU> on acpi0
Sep 16 03:41:05 mammoth kernel: cpu0: <ACPI CPU> on acpi0
Sep 16 03:41:05 mammoth kernel: acpi0: reservation of 100000, bf600000 (3) failed
Sep 16 03:41:05 mammoth kernel: acpi0: reservation of 0, a0000 (3) failed
Sep 16 03:41:05 mammoth kernel: acpi0: reservation of fee00000, 1000 (3) failed
Sep 16 03:41:05 mammoth kernel: acpi0: Power Button (fixed)
Sep 16 03:41:05 mammoth kernel: acpi0: <SMCI > on motherboard
Sep 16 03:41:05 mammoth kernel: cryptosoft0: <software crypto> on motherboard
Sep 16 03:41:05 mammoth kernel: kbd1 at kbdmux0
Sep 16 03:41:05 mammoth kernel: ioapic0 <Version 2.0> irqs 0-23 on motherboard
Sep 16 03:41:05 mammoth kernel: ioapic0: Changing APIC ID to 4
Sep 16 03:41:05 mammoth kernel: cpu3 (AP/HT): APIC ID: 3
Sep 16 03:41:05 mammoth kernel: cpu2 (AP): APIC ID: 2
Sep 16 03:41:05 mammoth kernel: cpu1 (AP/HT): APIC ID: 1
Sep 16 03:41:05 mammoth kernel: cpu0 (BSP): APIC ID: 0
Sep 16 03:41:05 mammoth kernel: FreeBSD/SMP: 1 package(s) x 2 core(s) x 2 HTT threads
Sep 16 03:41:05 mammoth kernel: FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
Sep 16 03:41:05 mammoth kernel: ACPI APIC Table: <022112 APIC1550>
Sep 16 03:41:05 mammoth kernel: Event timer "LAPIC" quality 400
Sep 16 03:41:05 mammoth kernel: avail memory = 3816116224 (3639 MB)
Sep 16 03:41:05 mammoth kernel: real memory = 4294967296 (4096 MB)
Sep 16 03:41:05 mammoth kernel: TSC: P-state invariant, performance statistics
Sep 16 03:41:05 mammoth kernel: AMD Features2=0x1<LAHF>
Sep 16 03:41:05 mammoth kernel: AMD Features=0x20100800<SYSCALL,NX,LM>
Sep 16 03:41:05 mammoth kernel: Features2=0x40e31d<SSE3,DTES64,MON,DS_CPL,TM2,SSSE3,CX16,xTPR,PDCM,MOVBE>
Sep 16 03:41:05 mammoth kernel: Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Sep 16 03:41:05 mammoth kernel: Origin = "GenuineIntel" Id = 0x106ca Family = 0x6 Model = 0x1c Stepping = 10
Sep 16 03:41:05 mammoth kernel: CPU: Intel(R) Atom(TM) CPU D525 @ 1.80GHz (1800.04-MHz K8-class CPU)
Sep 16 03:41:05 mammoth kernel: gcc version 4.2.1 20070831 patched [FreeBSD]
Sep 16 03:41:05 mammoth kernel: root@dev.nas4free.org:/usr/obj/nas4free/usr/src/sys/NAS4FREE-amd64 amd64
Sep 16 03:41:05 mammoth kernel: FreeBSD 9.2-RELEASE-p3 #0 r260900M: Mon Jan 20 07:22:46 CET 2014
Sep 16 03:41:05 mammoth kernel: FreeBSD is a registered trademark of The FreeBSD Foundation.
Sep 16 03:41:05 mammoth kernel: The Regents of the University of California. All rights reserved.
Sep 16 03:41:05 mammoth kernel: Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
Sep 16 03:41:05 mammoth kernel: Copyright (c) 1992-2013 The FreeBSD Project.
Sep 16 03:41:05 mammoth syslogd: kernel boot file is /boot/kernel/kernel-
robby6732
- NewUser
- Posts: 5
- Joined: 16 Sep 2014 02:15
- Status: Offline
Re: I can really use some help
Quick update:
Did a little bit more reading around online. I created the /mnt/Library folder (/mnt folder present but empty). Then I tried to mount /dev/ada0p1 and got an input output error. Tried to mount /dev/ada1p1 and it mounted and I can connect to the share from my Windows box and everything appears to be intact! The mount point is listed as OK in the webgui, the RAID is listed as stopped but I'm able to access the data (at least what I tried briefly). I guess a long term read to copy the data might give different results, guess I'll find out.
I think I'm going to try to just copy the data to the spare 1TB drive I have over the lan and pickup two new 2TB drives, since I've been meaning to upgrade for a while now anyway.
I'll just shut it down for now, I don't think I'll have time to do this until the weekend anyway. B0ssman, thanks for the input, and suggestions, it certainly helped! I wish I knew what happened.
Thanks again!
Did a little bit more reading around online. I created the /mnt/Library folder (/mnt folder present but empty). Then I tried to mount /dev/ada0p1 and got an input output error. Tried to mount /dev/ada1p1 and it mounted and I can connect to the share from my Windows box and everything appears to be intact! The mount point is listed as OK in the webgui, the RAID is listed as stopped but I'm able to access the data (at least what I tried briefly). I guess a long term read to copy the data might give different results, guess I'll find out.
I think I'm going to try to just copy the data to the spare 1TB drive I have over the lan and pickup two new 2TB drives, since I've been meaning to upgrade for a while now anyway.
I'll just shut it down for now, I don't think I'll have time to do this until the weekend anyway. B0ssman, thanks for the input, and suggestions, it certainly helped! I wish I knew what happened.
Thanks again!
-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: I can really use some help
Once you are done copying the data please post smart values if your drives.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
-
robby6732
- NewUser
- Posts: 5
- Joined: 16 Sep 2014 02:15
- Status: Offline
Re: I can really use some help
Sure, will do. Probably be after this weekend, but I'll post up the smart values of the drives.
-
robby6732
- NewUser
- Posts: 5
- Joined: 16 Sep 2014 02:15
- Status: Offline
Re: I can really use some help
I had some time and copied all the data off the one good drive to another drive, now I'm just waiting for the new drives I ordered to get here, sometime next week.
Here's the SMART data, looks like the one drive has 275 errors logged.
ada0
ada1
Here's the SMART data, looks like the one drive has 275 errors logged.
ada0
Code: Select all
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green
Device Model: WDC WD10EADS-00P8B0
Serial Number: WD-WMAVU3168222
LU WWN Device Id: 5 0014ee 6aabe9efd
Firmware Version: 01.00A01
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Sep 18 07:15:26 2014 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (27480) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 315) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3037) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 181 178 021 Pre-fail Always - 5941
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 219
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 050 050 000 Old_age Always - 36674
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 210
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 113
193 Load_Cycle_Count 0x0032 148 148 000 Old_age Always - 157198
194 Temperature_Celsius 0x0022 117 103 000 Old_age Always - 33
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 1
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 1
SMART Error Log Version: 1
ATA Error Count: 275 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 275 occurred at disk power-on lifetime: 36671 hours (1527 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 40 69 01 00 e0 Error: UNC 64 sectors at LBA = 0x00000169 = 361
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 62 01 00 e0 00 00:04:15.287 READ DMA
c8 00 40 62 01 00 e0 00 00:04:12.411 READ DMA
c8 00 40 62 01 00 e0 00 00:04:09.353 READ DMA
c8 00 40 62 01 00 e0 00 00:04:06.477 READ DMA
c8 00 40 62 01 00 e0 00 00:04:03.597 READ DMA
Error 274 occurred at disk power-on lifetime: 36671 hours (1527 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 40 69 01 00 e0 Error: UNC 64 sectors at LBA = 0x00000169 = 361
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 62 01 00 e0 00 00:04:12.411 READ DMA
c8 00 40 62 01 00 e0 00 00:04:09.353 READ DMA
c8 00 40 62 01 00 e0 00 00:04:06.477 READ DMA
c8 00 40 62 01 00 e0 00 00:04:03.597 READ DMA
c8 00 30 22 9e 00 e0 00 00:04:03.597 READ DMA
Error 273 occurred at disk power-on lifetime: 36671 hours (1527 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 40 69 01 00 e0 Error: UNC 64 sectors at LBA = 0x00000169 = 361
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 62 01 00 e0 00 00:04:09.353 READ DMA
c8 00 40 62 01 00 e0 00 00:04:06.477 READ DMA
c8 00 40 62 01 00 e0 00 00:04:03.597 READ DMA
c8 00 30 22 9e 00 e0 00 00:04:03.597 READ DMA
c8 00 10 a2 00 00 e0 00 00:04:03.597 READ DMA
Error 272 occurred at disk power-on lifetime: 36671 hours (1527 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 40 69 01 00 e0 Error: UNC 64 sectors at LBA = 0x00000169 = 361
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 62 01 00 e0 00 00:04:06.477 READ DMA
c8 00 40 62 01 00 e0 00 00:04:03.597 READ DMA
c8 00 30 22 9e 00 e0 00 00:04:03.597 READ DMA
c8 00 10 a2 00 00 e0 00 00:04:03.597 READ DMA
Error 271 occurred at disk power-on lifetime: 36671 hours (1527 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 40 69 01 00 e0 Error: UNC 64 sectors at LBA = 0x00000169 = 361
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 62 01 00 e0 00 00:04:03.597 READ DMA
c8 00 30 22 9e 00 e0 00 00:04:03.597 READ DMA
c8 00 10 a2 00 00 e0 00 00:04:03.597 READ DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 12471 -
# 2 Short offline Completed without error 00% 9749 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.ada1
Code: Select all
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green
Device Model: WDC WD10EADS-00P8B0
Serial Number: WD-WMAVU3154656
LU WWN Device Id: 5 0014ee 65567cc7d
Firmware Version: 01.00A01
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Sep 18 07:15:27 2014 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (30600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 349) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3037) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 179 177 021 Pre-fail Always - 6041
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 221
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 050 050 000 Old_age Always - 36674
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 212
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 115
193 Load_Cycle_Count 0x0032 148 148 000 Old_age Always - 156322
194 Temperature_Celsius 0x0022 116 103 000 Old_age Always - 34
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 9744 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.