S.M.A.R.T Reports

[paveld]

Hi All i have configure SMART Scanning and reports and got the following report,
I didnt find some guide how to read this report so i would like to get some help.
Thanks




S.M.A.R.T. [/dev/da0]:
----------------------
smartctl 6.2 2013-07-26 r3841 [FreeBSD 9.2-RELEASE-p4 amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda ES
Device Model: ST3750640NS
Serial Number: 3QD0KMX4
Firmware Version: 3.AEG
User Capacity: 750,156,374,016 bytes [750 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Sun Nov 16 10:15:00 2014 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART STATUS RETURN: incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 202) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 105 092 006 Pre-fail Always - 62764984
3 Spin_Up_Time 0x0003 094 093 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 69
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 088 060 030 Pre-fail Always - 692849870
9 Power_On_Hours 0x0032 080 080 000 Old_age Always - 17536
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 180
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 058 052 045 Old_age Always - 42 (Min/Max 42/45)
194 Temperature_Celsius 0x0022 042 048 000 Old_age Always - 42 (0 19 0 0 0)
195 Hardware_ECC_Recovered 0x001a 060 057 000 Old_age Always - 6827634
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended captive Completed without error 00% 1469 -
# 2 Short captive Completed without error 00% 1465 -
# 3 Extended captive Completed without error 00% 34 -
# 4 Short captive Completed without error 00% 32 -
# 5 Extended captive Completed without error 00% 30 -
# 6 Short captive Completed without error 00% 26 -
# 7 Extended captive Completed without error 00% 24 -
# 8 Short captive Completed without error 00% 22 -
# 9 Short captive Interrupted (host reset) 90% 21 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

[crowi]

some good explanation here:
http://en.wikipedia.org/wiki/S.M.A.R.T. ... attributes

[paveld]

some good explanation here:
http://en.wikipedia.org/wiki/S.M.A.R.T. ... attributes

Thanks i saw this, but there is no number they saing the as low it is or as hight it is is better, but how can i know based on my report if i have some problems with the drive?

[paveld]

OK,
I think i got it (FINALY)
The value is between 100 and 200, so seems that my HDDs are OK
Thanks a lot.