Hi
I shutdown my NAS for maintenance, and now, it doesn't want to boot
When I turn on my NAS, it's starting to boot and after few time, I get last line : load NOP GEOM class
and nothing more
Somebody has an idea?
What could be the problem ?
Many thanks for your help
This is the old XigmaNAS forum in read only mode,
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
NAS doesn't boot after shutdown
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
-
ernie
- Forum Moderator
- Posts: 1458
- Joined: 26 Aug 2012 19:09
- Location: France - Val d'Oise
- Status: Offline
Re: NAS doesn't boot after shutdown
Hello again 
Which type of maintenance ?
Perhaps a bad connection of Sata cable.
Which type of maintenance ?
Perhaps a bad connection of Sata cable.
NAS 1&2:
System: GA-6LXGH(BIOS: R01 04/30/2014) / 16 Go ECC
XigmaNAS 12.1.0.4 - Ingva (revision 7743) embedded
NAS1: Xeon E3 1241@3.5GHz, 2HDD@8To/mirror, 1SSD cache, Zlog on mirror, 1 UFS 300 Go
NAS2: G3220@3GHz, 2x3HDD@2To/strip+raidz1, 1SSD cache, Zlog on mirror
UPS: APC Back-UPS RS 900G
Case : Fractal Design XL R2
Extensions & services:
NAS1: OBI (Plex, BTSync, zrep, rclone, themes), nfs, smb, UPS,
NAS2: OBI (zrep (backup mode), themes)
System: GA-6LXGH(BIOS: R01 04/30/2014) / 16 Go ECC
XigmaNAS 12.1.0.4 - Ingva (revision 7743) embedded
NAS1: Xeon E3 1241@3.5GHz, 2HDD@8To/mirror, 1SSD cache, Zlog on mirror, 1 UFS 300 Go
NAS2: G3220@3GHz, 2x3HDD@2To/strip+raidz1, 1SSD cache, Zlog on mirror
UPS: APC Back-UPS RS 900G
Case : Fractal Design XL R2
Extensions & services:
NAS1: OBI (Plex, BTSync, zrep, rclone, themes), nfs, smb, UPS,
NAS2: OBI (zrep (backup mode), themes)
-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: NAS doesn't boot after shutdown
What version of nas4free? Full or embedded?
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
NAS 9.2
I will check all SATA cable
I will check all SATA cable
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
So
One disk seems defective
My nas is booting with a new HD
But this new HS came from an old ZFS pool
How can I add it to my pool?
One disk seems defective
My nas is booting with a new HD
But this new HS came from an old ZFS pool
How can I add it to my pool?
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
But, I have 6 HD 1To in my ZFS pool
Il 1 is unavailable, my files should be available again? Correct?
Her, no
I can see noting
Il 1 is unavailable, my files should be available again? Correct?
Her, no
I can see noting
-
crowi
- Forum Moderator
- Posts: 1176
- Joined: 21 Feb 2013 16:18
- Location: Munich, Germany
- Status: Offline
Re: NAS doesn't boot after shutdown
Please post the output of Disks|ZFS|Pool|Information
NAS 1: Milchkuh: Asrock C2550D4I, Intel Avoton C2550 Quad-Core, 16GB DDR3 ECC, 5x3TB WD Red RaidZ1 +60 GB SSD for ZIL/L2ARC, APC-Back UPS 350 CS, NAS4Free 11.0.0.4.3460 embedded
NAS 2: Backup: HP N54L, 8 GB ECC RAM, 4x4 TB WD Red, RaidZ1, NAS4Free 11.0.0.4.3460 embedded
NAS 3: Office: HP N54L, 8 GB ECC RAM, 2x3 TB WD Red, ZFS Mirror, APC-Back UPS 350 CS NAS4Free 11.0.0.4.3460 embedded
NAS 2: Backup: HP N54L, 8 GB ECC RAM, 4x4 TB WD Red, RaidZ1, NAS4Free 11.0.0.4.3460 embedded
NAS 3: Office: HP N54L, 8 GB ECC RAM, 2x3 TB WD Red, ZFS Mirror, APC-Back UPS 350 CS NAS4Free 11.0.0.4.3460 embedded
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
Following :
datapool is pool name of my new HD
I would like to kill it and replace defective one on pool1 (my pool) with it
Code: Select all
pool: datapool
state: ONLINE
status: The pool is formatted using a legacy on-disk format. The pool can
still be used, but some features are unavailable.
action: Upgrade the pool using 'zpool upgrade'. Once this is done, the
pool will no longer be accessible on software that does not support feature
flags.
scan: none requested
config:
NAME STATE READ WRITE CKSUM
datapool ONLINE 0 0 0
ada6s4 ONLINE 0 0 0
errors: No known data errors
pool: pool_1
state: DEGRADED
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the
entire pool from backup.
see: http://illumos.org/msg/ZFS-8000-8A
scan: resilvered 29K in 0h0m with 1 errors on Fri May 22 22:16:36 2015
config:
NAME STATE READ WRITE CKSUM
pool_1 DEGRADED 0 0 5
raidz1-0 DEGRADED 0 0 20
ada0 ONLINE 0 0 0
ada1 ONLINE 0 0 0
ada2 ONLINE 0 0 0
ada3 ONLINE 0 0 0
ada5 ONLINE 0 0 0
7525484579836908893 UNAVAIL 0 0 0 was /dev/ada6
errors: Permanent errors have been detected in the following files:
pool_1:<0x0>I would like to kill it and replace defective one on pool1 (my pool) with it
-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: NAS doesn't boot after shutdown
you used a single parity setup and run into the raid 5 problem.
see
http://www.zdnet.com/article/why-raid-5 ... g-in-2009/
see
http://www.zdnet.com/article/why-raid-5 ... g-in-2009/
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
Can you explain me where you have seen I run into RAID5 ?
I'm not very ZFS fluent and need to understand my problem
What should I do?
I'm not very ZFS fluent and need to understand my problem
What should I do?
-
raulfg3
- Site Admin
- Posts: 4865
- Joined: 22 Jun 2012 22:13
- Location: Madrid (ESPAÑA)
- Contact:
- Status: Offline
Re: NAS doesn't boot after shutdown
be sure no data in datapool
zpool destroy datapool <- https://www.freebsd.org/cgi/man.cgi?que ... .0-RELEASE
and then use wiki:
http://wiki.nas4free.org/doku.php?id=faq:0149
usefull too: http://wiki.nas4free.org/doku.php?id=documentation:faq
zpool destroy datapool <- https://www.freebsd.org/cgi/man.cgi?que ... .0-RELEASE
and then use wiki:
http://wiki.nas4free.org/doku.php?id=faq:0149
usefull too: http://wiki.nas4free.org/doku.php?id=documentation:faq
12.1.0.4 - Ingva (revision 7743) on SUPERMICRO X8SIL-F 8GB of ECC RAM, 11x3TB disk in 1 vdev = Vpool = 32TB Raw size , so 29TB usable size (I Have other NAS as Backup)
Wiki
Last changes
HP T510
Wiki
Last changes
HP T510
-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: NAS doesn't boot after shutdown
raidz1 is equivalent to raid5françois ROLAND wrote:Can you explain me where you have seen I run into RAID5 ?
I'm not very ZFS fluent and need to understand my problem
What should I do?
if one drives dies any corruption can not be repaired
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
I follow your info to remove new disk from its pool
and I selected "replace" to add in to my pool1
now, I have that :
But I'm not sure my pool is rebuildig
and I selected "replace" to add in to my pool1
now, I have that :
Code: Select all
pool: pool_1
state: DEGRADED
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
action: Restore the file in question if possible. Otherwise restore the
entire pool from backup.
see: http://illumos.org/msg/ZFS-8000-8A
scan: scrub repaired 0 in 0h0m with 1 errors on Sat May 23 13:44:26 2015
config:
NAME STATE READ WRITE CKSUM
pool_1 DEGRADED 0 0 62
raidz1-0 DEGRADED 0 0 248
ada0 ONLINE 0 0 0
ada1 ONLINE 0 0 0
ada2 ONLINE 0 0 0
ada3 ONLINE 0 0 0
ada5 ONLINE 0 0 0
replacing-5 DEGRADED 0 0 0
7525484579836908893 UNAVAIL 0 0 0 was /dev/ada6/old
ada6 ONLINE 0 0 0
errors: Permanent errors have been detected in the following files:
pool_1:<0x0>-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: NAS doesn't boot after shutdown
pls post the smart values of all your drives
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
below :
Code: Select all
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES.3
Device Model: ST1000NM0033-9ZM173
Serial Number: Z1W1NR83
LU WWN Device Id: 5 000c50 066740646
Firmware Version: SN03
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sat May 23 14:23:53 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 592) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 119) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 081 064 044 Pre-fail Always - 149036035
3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 82
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 077 060 030 Pre-fail Always - 52609780
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1105
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 82
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 062 056 045 Old_age Always - 38 (Min/Max 36/38)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 76
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 122
194 Temperature_Celsius 0x0022 038 044 000 Old_age Always - 38 (0 22 0 0 0)
195 Hardware_ECC_Recovered 0x001a 033 017 000 Old_age Always - 149036035
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Périphérique /dev/ada1 - Western Digital Caviar Green
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green
Device Model: WDC WD10EADS-00L5B1
Serial Number: WD-WCAU46904150
LU WWN Device Id: 5 0014ee 257cca11e
Firmware Version: 01.01A01
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.5, 3.0 Gb/s
Local Time is: Sat May 23 14:23:53 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (22800) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 262) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 161 159 021 Pre-fail Always - 6916
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2039
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 18586
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1813
192 Power-Off_Retract_Count 0x0032 199 199 000 Old_age Always - 835
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 2039
194 Temperature_Celsius 0x0022 112 100 000 Old_age Always - 38
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 3
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 3
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 17
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Périphérique /dev/ada2 - Seagate Constellation ES (SATA 6Gb/s)
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES (SATA 6Gb/s)
Device Model: ST1000NM0011
Serial Number: Z1N1NXAN
LU WWN Device Id: 5 000c50 04d2acb73
Firmware Version: SN02
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7202 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sat May 23 14:23:53 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 617) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 162) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x10bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 080 063 044 Pre-fail Always - 101165981
3 Spin_Up_Time 0x0003 095 093 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 822
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 4418124621
9 Power_On_Hours 0x0032 085 085 000 Old_age Always - 13961
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 139
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 061 049 045 Old_age Always - 39 (Min/Max 38/39)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 1801
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 72
193 Load_Cycle_Count 0x0032 094 094 000 Old_age Always - 13205
194 Temperature_Celsius 0x0022 039 051 000 Old_age Always - 39 (0 17 0 0 0)
195 Hardware_ECC_Recovered 0x001a 116 099 000 Old_age Always - 101165981
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Périphérique /dev/ada3 - Seagate Constellation ES (SATA 6Gb/s)
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES (SATA 6Gb/s)
Device Model: ST1000NM0011
Serial Number: Z1N1P5FQ
LU WWN Device Id: 5 000c50 04d2c5933
Firmware Version: SN02
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7202 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sat May 23 14:23:54 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 609) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 155) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x10bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 081 063 044 Pre-fail Always - 166117233
3 Spin_Up_Time 0x0003 095 094 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 832
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 118720753
9 Power_On_Hours 0x0032 085 085 000 Old_age Always - 13946
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 139
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 054 000 Old_age Always - 103080788036
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 063 050 045 Old_age Always - 37 (Min/Max 36/37)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 79
193 Load_Cycle_Count 0x0032 094 094 000 Old_age Always - 13203
194 Temperature_Celsius 0x0022 037 050 000 Old_age Always - 37 (0 16 0 0 0)
195 Hardware_ECC_Recovered 0x001a 117 099 000 Old_age Always - 166117233
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 165 000 Old_age Always - 6136
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Périphérique /dev/ada4 - Seagate U10
=== START OF INFORMATION SECTION ===
Model Family: Seagate U10
Device Model: ST310212A
Serial Number: 7EG255WP
Firmware Version: 3.02
User Capacity: 10,242,892,800 bytes [10.2 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-5 (minor revision not indicated)
Local Time is: Sat May 23 14:23:54 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 2400) seconds.
Offline data collection
capabilities: (0x1d) SMART execute Offline immediate.
No Auto Offline data collection support.
Abort Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 14) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x0008 083 064 000 Old_age Offline - 24590997
3 Spin_Up_Time 0x0006 098 098 000 Old_age Always - 0
4 Start_Stop_Count 0x0013 097 097 020 Pre-fail Always - 3477
5 Reallocated_Sector_Ct 0x0013 100 100 036 Pre-fail Always - 22
7 Seek_Error_Rate 0x0009 075 060 030 Pre-fail Offline - 12985719741
9 Power_On_Hours 0x0012 079 079 000 Old_age Always - 18960
10 Spin_Retry_Count 0x0013 100 100 090 Pre-fail Always - 0
12 Power_Cycle_Count 0x0013 097 097 000 Pre-fail Always - 3492
197 Current_Pending_Sector 0x0030 100 100 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 40 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 40 occurred at disk power-on lifetime: 8566 hours (356 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 40 72 0f e0 Error: ICRC, ABRT at LBA = 0x000f7240 = 1012288
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 10 40 72 0f e0 00 00:05:42.053 READ DMA
c8 00 10 40 72 0f e0 00 00:05:41.789 READ DMA
c8 00 10 40 72 0f e0 00 00:05:41.553 READ DMA
c8 00 10 c0 73 0f e0 00 00:05:41.548 READ DMA
c8 00 10 40 72 0f e0 00 00:05:41.519 READ DMA
Error 39 occurred at disk power-on lifetime: 8566 hours (356 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 40 72 0f e0 Error: ICRC, ABRT at LBA = 0x000f7240 = 1012288
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 10 40 72 0f e0 00 00:05:41.789 READ DMA
c8 00 10 40 72 0f e0 00 00:05:41.553 READ DMA
c8 00 10 c0 73 0f e0 00 00:05:41.548 READ DMA
c8 00 10 40 72 0f e0 00 00:05:41.519 READ DMA
c8 00 01 7f 30 31 e1 00 00:05:41.492 READ DMA
Error 38 occurred at disk power-on lifetime: 8566 hours (356 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 40 72 0f e0 Error: ICRC, ABRT at LBA = 0x000f7240 = 1012288
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 10 40 72 0f e0 00 00:05:41.553 READ DMA
c8 00 10 c0 73 0f e0 00 00:05:41.548 READ DMA
c8 00 10 40 72 0f e0 00 00:05:41.519 READ DMA
c8 00 01 7f 30 31 e1 00 00:05:41.492 READ DMA
c8 00 01 c0 71 0f e0 00 00:05:41.491 READ DMA
Error 37 occurred at disk power-on lifetime: 8566 hours (356 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 c0 72 0f e0 Error: ICRC, ABRT at LBA = 0x000f72c0 = 1012416
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 c0 72 0f e0 00 00:05:40.951 READ DMA
c8 00 40 c0 72 0f e0 00 00:05:40.692 READ DMA
c8 00 40 c0 72 0f e0 00 00:05:40.456 READ DMA
ca 00 08 c0 cf 0f e0 00 00:05:40.438 WRITE DMA
ca 00 40 c0 72 0f e0 00 00:05:40.438 WRITE DMA
Error 36 occurred at disk power-on lifetime: 8566 hours (356 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 c0 72 0f e0 Error: ICRC, ABRT at LBA = 0x000f72c0 = 1012416
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 c0 72 0f e0 00 00:05:40.692 READ DMA
c8 00 40 c0 72 0f e0 00 00:05:40.456 READ DMA
ca 00 08 c0 cf 0f e0 00 00:05:40.438 WRITE DMA
ca 00 40 c0 72 0f e0 00 00:05:40.438 WRITE DMA
c8 00 40 c0 72 0f e0 00 00:05:40.416 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Selective Self-tests/Logging not supported
Périphérique /dev/ada5 - Western Digital Caviar Green
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green
Device Model: WDC WD10EADS-00L5B1
Serial Number: WD-WCAU46890238
LU WWN Device Id: 5 0014ee 2ad22c097
Firmware Version: 01.01A01
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.5, 3.0 Gb/s
Local Time is: Sat May 23 14:23:54 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (22800) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 262) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 1
3 Spin_Up_Time 0x0027 164 160 021 Pre-fail Always - 6758
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1069
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 18776
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 562
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 229
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 1069
194 Temperature_Celsius 0x0022 113 098 000 Old_age Always - 37
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 3
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Périphérique /dev/ada6 -
=== START OF INFORMATION SECTION ===
Device Model: HITACHI H7210CA30SUN1.0T 1051AA068L
Serial Number: JPW9K0HZ0A068L
LU WWN Device Id: 5 000cca 375c48c78
Firmware Version: JP4OA3CB
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat May 23 14:23:54 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9929) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 166) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 136 136 054 Pre-fail Offline - 94
3 Spin_Up_Time 0x0007 123 123 024 Pre-fail Always - 325 (Average 291)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 92
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 132 132 020 Pre-fail Offline - 34
9 Power_On_Hours 0x0012 098 098 000 Old_age Always - 20396
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 88
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 194
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 194
194 Temperature_Celsius 0x0002 181 181 000 Old_age Always - 33 (Min/Max 17/38)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 0
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: NAS doesn't boot after shutdown
This drive is failing and has a bad sata cable
Serial Number: WD-WCAU46904150
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 3
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 3
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 17
This drive is failing
Serial Number: Z1N1NXAN
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1
This drive has a bad sata cable
Serial Number: Z1N1P5FQ
199 UDMA_CRC_Error_Count 0x003e 200 165 000 Old_age Always - 6136
This drive is failing
Serial Number: 7EG255WP
5 Reallocated_Sector_Ct 0x0013 100 100 036 Pre-fail Always - 22
This drive has a bad sata cable
Serial Number: WD-WCAU46890238
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 3
Serial Number: WD-WCAU46904150
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 3
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 3
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 17
This drive is failing
Serial Number: Z1N1NXAN
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1
This drive has a bad sata cable
Serial Number: Z1N1P5FQ
199 UDMA_CRC_Error_Count 0x003e 200 165 000 Old_age Always - 6136
This drive is failing
Serial Number: 7EG255WP
5 Reallocated_Sector_Ct 0x0013 100 100 036 Pre-fail Always - 22
This drive has a bad sata cable
Serial Number: WD-WCAU46890238
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 3
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
And do you think is the reason my new disk is not repearing pool?
My goal is to do a backup of my data
My goal is to do a backup of my data
-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: NAS doesn't boot after shutdown
yes that is the reason for the zpool status
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
status: One or more devices has experienced an error resulting in data
corruption. Applications may be affected.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
So
If I start to replace all SATA cable, do you beleive I could get my data?
If I start to replace all SATA cable, do you beleive I could get my data?
-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: NAS doesn't boot after shutdown
well the error in the file <0x0> means an error in the metadata. i.e the file system information, which is really bad.
what is the output of the mount command?
what is the output of the mount command?
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
Can you tell me more about the mount commande?
-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: NAS doesn't boot after shutdown
you go to the console and type mount.
this is to see if the zfs array is mounted.
this is to see if the zfs array is mounted.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
below, mount commande
Code: Select all
/dev/md0 on / (ufs, local)
devfs on /dev (devfs, local, multilabel)
/dev/ada4a on /cf (ufs, local, read-only)
procfs on /proc (procfs, local)
/dev/md1 on /var (ufs, local)
-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: NAS doesn't boot after shutdown
degraded and not mounted. with the metadata corruption i dont know if you can even recover any data.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
Not Time to Check today, but I will try at first to change SATA cables and see
I'll let you know
Thanks for your help
I'll let you know
Thanks for your help
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
Hi
I'm coming backe after some weeks very busy
I start to replace ALL SATA cable for my 6 hard drive
But I get same error for same Hard disk
Really crasy. Is it a cable issue?
Is a too small power supply able to do that ?
I'm coming backe after some weeks very busy
I start to replace ALL SATA cable for my 6 hard drive
But I get same error for same Hard disk
Really crasy. Is it a cable issue?
Is a too small power supply able to do that ?
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
new SMART to compare with old one
Code: Select all
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES.3
Device Model: ST1000NM0033-9ZM173
Serial Number: Z1W1NR83
LU WWN Device Id: 5 000c50 066740646
Firmware Version: SN03
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Fri Jun 12 16:16:30 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 592) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 119) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 081 064 044 Pre-fail Always - 153459297
3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 85
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 077 060 030 Pre-fail Always - 54220299
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1115
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 85
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 065 056 045 Old_age Always - 35 (Min/Max 27/35)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 76
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 125
194 Temperature_Celsius 0x0022 035 044 000 Old_age Always - 35 (0 22 0 0 0)
195 Hardware_ECC_Recovered 0x001a 033 017 000 Old_age Always - 153459297
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Périphérique /dev/ada1 - Western Digital Caviar Green
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green
Device Model: WDC WD10EADS-00L5B1
Serial Number: WD-WCAU46904150
LU WWN Device Id: 5 0014ee 257cca11e
Firmware Version: 01.01A01
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.5, 3.0 Gb/s
Local Time is: Fri Jun 12 16:16:31 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (22800) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 262) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 161 159 021 Pre-fail Always - 6916
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2042
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 18597
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1816
192 Power-Off_Retract_Count 0x0032 199 199 000 Old_age Always - 835
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 2042
194 Temperature_Celsius 0x0022 116 100 000 Old_age Always - 34
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 3
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 3
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 17
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Périphérique /dev/ada2 - Seagate Constellation ES (SATA 6Gb/s)
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES (SATA 6Gb/s)
Device Model: ST1000NM0011
Serial Number: Z1N1NXAN
LU WWN Device Id: 5 000c50 04d2acb73
Firmware Version: SN02
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7202 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Fri Jun 12 16:16:31 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 617) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 162) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x10bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 080 063 044 Pre-fail Always - 105204646
3 Spin_Up_Time 0x0003 095 093 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 825
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 4418138349
9 Power_On_Hours 0x0032 085 085 000 Old_age Always - 13971
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 142
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 066 049 045 Old_age Always - 34 (Min/Max 26/34)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 1801
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 72
193 Load_Cycle_Count 0x0032 094 094 000 Old_age Always - 13208
194 Temperature_Celsius 0x0022 034 051 000 Old_age Always - 34 (0 17 0 0 0)
195 Hardware_ECC_Recovered 0x001a 116 099 000 Old_age Always - 105204646
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Périphérique /dev/ada3 - Seagate Constellation ES (SATA 6Gb/s)
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES (SATA 6Gb/s)
Device Model: ST1000NM0011
Serial Number: Z1N1P5FQ
LU WWN Device Id: 5 000c50 04d2c5933
Firmware Version: SN02
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7202 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Fri Jun 12 16:16:31 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 609) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 155) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x10bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 082 063 044 Pre-fail Always - 170211118
3 Spin_Up_Time 0x0003 095 094 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 835
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 118734526
9 Power_On_Hours 0x0032 085 085 000 Old_age Always - 13956
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 142
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 054 000 Old_age Always - 103080788036
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 067 050 045 Old_age Always - 33 (Min/Max 26/33)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 79
193 Load_Cycle_Count 0x0032 094 094 000 Old_age Always - 13206
194 Temperature_Celsius 0x0022 033 050 000 Old_age Always - 33 (0 16 0 0 0)
195 Hardware_ECC_Recovered 0x001a 118 099 000 Old_age Always - 170211118
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 165 000 Old_age Always - 6136
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Périphérique /dev/ada4 - Seagate U10
=== START OF INFORMATION SECTION ===
Model Family: Seagate U10
Device Model: ST310212A
Serial Number: 7EG255WP
Firmware Version: 3.02
User Capacity: 10,242,892,800 bytes [10.2 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-5 (minor revision not indicated)
Local Time is: Fri Jun 12 16:16:32 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 2400) seconds.
Offline data collection
capabilities: (0x1d) SMART execute Offline immediate.
No Auto Offline data collection support.
Abort Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 14) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x0008 083 064 000 Old_age Offline - 55071005
3 Spin_Up_Time 0x0006 098 098 000 Old_age Always - 0
4 Start_Stop_Count 0x0013 097 097 020 Pre-fail Always - 3477
5 Reallocated_Sector_Ct 0x0013 100 100 036 Pre-fail Always - 22
7 Seek_Error_Rate 0x0009 075 060 030 Pre-fail Offline - 12985779799
9 Power_On_Hours 0x0012 079 079 000 Old_age Always - 18970
10 Spin_Retry_Count 0x0013 100 100 090 Pre-fail Always - 0
12 Power_Cycle_Count 0x0013 097 097 000 Pre-fail Always - 3495
197 Current_Pending_Sector 0x0030 100 100 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 40 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 40 occurred at disk power-on lifetime: 8566 hours (356 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 40 72 0f e0 Error: ICRC, ABRT at LBA = 0x000f7240 = 1012288
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 10 40 72 0f e0 00 00:05:42.053 READ DMA
c8 00 10 40 72 0f e0 00 00:05:41.789 READ DMA
c8 00 10 40 72 0f e0 00 00:05:41.553 READ DMA
c8 00 10 c0 73 0f e0 00 00:05:41.548 READ DMA
c8 00 10 40 72 0f e0 00 00:05:41.519 READ DMA
Error 39 occurred at disk power-on lifetime: 8566 hours (356 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 40 72 0f e0 Error: ICRC, ABRT at LBA = 0x000f7240 = 1012288
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 10 40 72 0f e0 00 00:05:41.789 READ DMA
c8 00 10 40 72 0f e0 00 00:05:41.553 READ DMA
c8 00 10 c0 73 0f e0 00 00:05:41.548 READ DMA
c8 00 10 40 72 0f e0 00 00:05:41.519 READ DMA
c8 00 01 7f 30 31 e1 00 00:05:41.492 READ DMA
Error 38 occurred at disk power-on lifetime: 8566 hours (356 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 40 72 0f e0 Error: ICRC, ABRT at LBA = 0x000f7240 = 1012288
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 10 40 72 0f e0 00 00:05:41.553 READ DMA
c8 00 10 c0 73 0f e0 00 00:05:41.548 READ DMA
c8 00 10 40 72 0f e0 00 00:05:41.519 READ DMA
c8 00 01 7f 30 31 e1 00 00:05:41.492 READ DMA
c8 00 01 c0 71 0f e0 00 00:05:41.491 READ DMA
Error 37 occurred at disk power-on lifetime: 8566 hours (356 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 c0 72 0f e0 Error: ICRC, ABRT at LBA = 0x000f72c0 = 1012416
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 c0 72 0f e0 00 00:05:40.951 READ DMA
c8 00 40 c0 72 0f e0 00 00:05:40.692 READ DMA
c8 00 40 c0 72 0f e0 00 00:05:40.456 READ DMA
ca 00 08 c0 cf 0f e0 00 00:05:40.438 WRITE DMA
ca 00 40 c0 72 0f e0 00 00:05:40.438 WRITE DMA
Error 36 occurred at disk power-on lifetime: 8566 hours (356 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 c0 72 0f e0 Error: ICRC, ABRT at LBA = 0x000f72c0 = 1012416
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 40 c0 72 0f e0 00 00:05:40.692 READ DMA
c8 00 40 c0 72 0f e0 00 00:05:40.456 READ DMA
ca 00 08 c0 cf 0f e0 00 00:05:40.438 WRITE DMA
ca 00 40 c0 72 0f e0 00 00:05:40.438 WRITE DMA
c8 00 40 c0 72 0f e0 00 00:05:40.416 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Selective Self-tests/Logging not supported
Périphérique /dev/ada5 - Western Digital Caviar Green
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green
Device Model: WDC WD10EADS-00L5B1
Serial Number: WD-WCAU46890238
LU WWN Device Id: 5 0014ee 2ad22c097
Firmware Version: 01.01A01
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.5, 3.0 Gb/s
Local Time is: Fri Jun 12 16:16:32 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (22800) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 262) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 1
3 Spin_Up_Time 0x0027 165 160 021 Pre-fail Always - 6725
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1072
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 075 075 000 Old_age Always - 18786
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 565
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 229
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 1072
194 Temperature_Celsius 0x0022 117 098 000 Old_age Always - 33
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 3
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Périphérique /dev/ada6 -
=== START OF INFORMATION SECTION ===
Device Model: HITACHI H7210CA30SUN1.0T 1051AA068L
Serial Number: JPW9K0HZ0A068L
LU WWN Device Id: 5 000cca 375c48c78
Firmware Version: JP4OA3CB
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Fri Jun 12 16:16:32 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 9929) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 166) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 136 136 054 Pre-fail Offline - 95
3 Spin_Up_Time 0x0007 120 120 024 Pre-fail Always - 304 (Average 325)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 95
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 132 132 020 Pre-fail Offline - 34
9 Power_On_Hours 0x0012 098 098 000 Old_age Always - 20407
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 91
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 197
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 197
194 Temperature_Celsius 0x0002 193 193 000 Old_age Always - 31 (Min/Max 17/38)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 0
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: NAS doesn't boot after shutdown
new sata cables wont make the errors on the drive disappear.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.
-
françois ROLAND
- experienced User
- Posts: 94
- Joined: 28 Aug 2013 13:50
- Status: Offline
Re: NAS doesn't boot after shutdown
So, how could I fix SATA cable problem?
-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: NAS doesn't boot after shutdown
i was talking about the state of your array.
you should change the sata cables. but those are the least of your problems.
you should change the sata cables. but those are the least of your problems.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.