Hello
Today nas4free gives smart report in the diagnostic/information menu.
But it is with technical code.
Based on the experience of extended gui and rrdgraph, is it possible to optimise the interface as the following example ?
http://www.mesoutils.com/ordi/smart.php
Sorry it is in French , but the principle is a table with color code if there is issue.
I am not expert of SMART and it will be helpful.
BR
This is the old XigmaNAS forum in read only mode,
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
it will taken offline by the end of march 2021!
I like to aks Users and Admins to rewrite/take over important post from here into the new fresh main forum!
Its not possible for us to export from here and import it to the main forum!
[Solved] SMART interpretation
-
ernie
- Forum Moderator
- Posts: 1458
- Joined: 26 Aug 2012 19:09
- Location: France - Val d'Oise
- Status: Offline
[Solved] SMART interpretation
Last edited by ernie on 01 Aug 2016 13:54, edited 1 time in total.
NAS 1&2:
System: GA-6LXGH(BIOS: R01 04/30/2014) / 16 Go ECC
XigmaNAS 12.1.0.4 - Ingva (revision 7743) embedded
NAS1: Xeon E3 1241@3.5GHz, 2HDD@8To/mirror, 1SSD cache, Zlog on mirror, 1 UFS 300 Go
NAS2: G3220@3GHz, 2x3HDD@2To/strip+raidz1, 1SSD cache, Zlog on mirror
UPS: APC Back-UPS RS 900G
Case : Fractal Design XL R2
Extensions & services:
NAS1: OBI (Plex, BTSync, zrep, rclone, themes), nfs, smb, UPS,
NAS2: OBI (zrep (backup mode), themes)
System: GA-6LXGH(BIOS: R01 04/30/2014) / 16 Go ECC
XigmaNAS 12.1.0.4 - Ingva (revision 7743) embedded
NAS1: Xeon E3 1241@3.5GHz, 2HDD@8To/mirror, 1SSD cache, Zlog on mirror, 1 UFS 300 Go
NAS2: G3220@3GHz, 2x3HDD@2To/strip+raidz1, 1SSD cache, Zlog on mirror
UPS: APC Back-UPS RS 900G
Case : Fractal Design XL R2
Extensions & services:
NAS1: OBI (Plex, BTSync, zrep, rclone, themes), nfs, smb, UPS,
NAS2: OBI (zrep (backup mode), themes)
-
b0ssman
- Forum Moderator
- Posts: 2438
- Joined: 14 Feb 2013 08:34
- Location: Munich, Germany
- Status: Offline
Re: SMART interpretation
to be honest i never liked that representation and the raw values are much more helpful.
a good read is here
https://www.backblaze.com/blog/hard-drive-smart-stats/
basically if any of those values goes above 0 start thinking about replacing that drive.
a good read is here
https://www.backblaze.com/blog/hard-drive-smart-stats/
basically if any of those values goes above 0 start thinking about replacing that drive.
Nas4Free 11.1.0.4.4517. Supermicro X10SLL-F, 16gb ECC, i3 4130, IBM M1015 with IT firmware. 4x 3tb WD Red, 4x 2TB Samsung F4, both GEOM AES 256 encrypted.